Zanussi ZGH62414XS manual

Zanussi ZGH62414XS
7.2 · 1
PDF manual
 · 20 pages
English
manualZanussi ZGH62414XS
Do not install the appliance adjacent to a door
or under a window. This prevents hot cookware
falling from the appliance when the door or the
window is opened.
If the appliance is installed above drawers make
sure that the space, between the bottom of the
appliance and the upper drawer, is sufficient for
air circulation.
The underside of the appliance can get hot
when in use. If an oven has not been fitted
underneath the hob and underside of the
appliance is accessible and could allow a user
or items stored beneath the hob to come in
direct contact with the underside of the hob, an
intermediate protection panel must be fitted.
Plywood or kitchen carcass material is
acceptable for the panel.
The panel must be removable for servicing.
Screws used to fix the panel must be accessible
after installation.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
All electrical connections should be made by a
qualified electrician.
The appliance must be earthed.
Before carrying out any operation make sure
that the appliance is disconnected from the
power supply.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Make sure the appliance is installed correctly.
Loose and incorrect electricity mains cable or
plug (if applicable) can make the terminal
become too hot.
Use the correct electricity mains cable.
Do not let the electricity mains cable tangle.
Make sure that a shock protection is installed.
Use the strain relief clamp on the cable.
Make sure the mains cable or plug (if
applicable) does not touch the hot appliance or
hot cookware, when you connect the appliance
to the near sockets.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug (if applicable) or to the mains cable.
Contact our Authorised Service Centre or an
electrician to change a damaged mains cable.
The shock protection of live and insulated parts
must be fastened in such a way that it cannot be
removed without tools.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
If the mains socket is loose, do not connect the
mains plug.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), earth leakage trips
and contactors.
The electrical installation must have an isolation
device which lets you disconnect the appliance
from the mains at all poles. The isolation device
must have a contact opening width of minimum
3 mm.
GAS CONNECTION
WARNING! These instructions are
only valid if the country symbol
appears on the appliance. If the
symbol does not appear on the
appliance, it is necessary to refer to
the technical instructions which will
provide the necessary instructions
concerning modification of the
appliance to the conditions of use of
the country.
All gas connections should be made by a
qualified person.
Before installation, make sure that the local
distribution conditions (nature of the gas and
gas pressure) and the adjustment of the
appliance are compatible.
Make sure that there is air circulation around the
appliance.
The information about the gas supply is on the
rating plate.
This appliance is not connected to a device,
which evacuates the products of combustion.
Make sure to connect the appliance according
to current installation regulations. Pay attention
to requirements regarding adequate ventilation.
USE
WARNING! Risk of injury, burns and
electric shock.
Remove all the packaging, labelling and
protective film (if applicable) before first use.
Use this appliance in a household environment.
Do not change the specification of this
appliance.
Make sure that the ventilation openings are not
blocked.
4

Manual

View the manual for the Zanussi ZGH62414XS here, for free. This manual comes under the category stoves and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Zanussi ZGH62414XS or do you need help? Ask your question here

Need help?

Do you have a question about the Zanussi and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Zanussi ZGH62414XS specifications

Below you will find the product specifications and the manual specifications of the Zanussi ZGH62414XS.

The Zanussi ZGH62414XS stove is a gas hob with four cooking zones, all of which are gas-powered. This stove does not have any electric cooking zones. The simmer cooking zone is round in shape, as are the regular and large cooking zones. It is designed for easy cleaning, making maintenance hassle-free. The stove has a width of 594 millimeters, a depth of 510 millimeters, and requires an installation compartment height of 43 millimeters. The Zanussi ZGH62414XS stove offers users the flexibility of four gas cooking zones in various sizes and shapes to accommodate different cooking needs. With its compact design and easy-to-clean features, this gas stove is a practical addition to any kitchen.

General
BrandZanussi
ModelZGH62414XS | ZGH62414XS
Productstove
EAN7332543587384
LanguageEnglish
FiletypeUser manual (PDF), Datasheet (PDF)
Design
Hob typeGas
Number of cooking zones4 zone(s)
Number of gas cooking zones4 zone(s)
Number of electric cooking zones0 zone(s)
Simmer cooking zone shapeRound
Regular cooking zone shapeRound
Large cooking zone shapeRound
Appliance placementBuilt-in
Product colorStainless steel
Pan support materialEnameled
Simmer cooking zone diameter54 mm
Regular cooking zone diameter70 mm
Large cooking zone diameter100 mm
Hob width size60 cm
Top surface type-
Number of simultaneously used cooking zones4
Cooking zone 4 typeSimmer
Cooking zone 1 shapeRound
Cooking zone 3 typeRegular
Cooking zone 1 power2000 W
Cooking zone 3 power sourceGas
Cooking zone 2 positionLeft front
Cooking zone 3 power2000 W
Cooking zone 4 shapeRound
Cooking zone 3 positionRight rear
Cooking zone 4 diameter54 mm
Cooking zone 2 shapeRound
Cooking zone 3 diameter70 mm
Cooking zone 4 power1000 W
Cooking zone 4 positionRight front
Cooking zone 1 diameter70 mm
Cooking zone 1 typeRegular
Cooking zone 4 power sourceGas
Cooking zone 3 shapeRound
Cooking zone 2 typeLarge
Cooking zone 1 positionLeft rear
Cooking zone 2 power sourceGas
Cooking zone 2 power3000 W
Cooking zone 1 power sourceGas
Cooking zone 2 diameter100 mm
Ergonomics
Easy to cleanYes
Control typeRotary
Built-in displayNo
Control positionTop right
Electronic ignitionYes
Child lock-
Weight & dimensions
Width594 mm
Depth510 mm
Height- mm
Installation compartment height43 mm
Installation compartment width550 mm
Installation compartment depth470 mm
Cord length1.1 m
Performance
Number of power levels-
Thermocouple protectionYes
Regular cooking zone2000 W
Simmer cooking zone1000 W
Large cooking zone3000 W
Power
Connected load (gas)8000 W
AC input voltage220 - 240 V
AC input frequency50 - 60 Hz
Connected load (electric)- W
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Zanussi ZGH62414XS below.

Can I use my pans on induction?

Nowadays almost all pans are suitable for induction. You can easily test whether your old pans can also be used on induction by holding a magnet against the bottom of the pan. If the magnet stays on the pan, your old pan is suitable for induction.

How do I reset my induction hob?

Most induction hobs can be reset by disconnecting the hob from power by unplugging it from the power outlet. You will then have to wait at least 60 minutes.

What is a Perilex connection?

A Perilex connection is a special connection that can handle more power than a normal connection. This connection has five holes instead of two and is often used for induction hobs.

Is cooking on induction dangerous?

No, cooking on induction is not dangerous.

What is the height of the Zanussi ZGH62414XS?

The Zanussi ZGH62414XS has a height of - mm.

What is the width of the Zanussi ZGH62414XS?

The Zanussi ZGH62414XS has a width of 594 mm.

What is the depth of the Zanussi ZGH62414XS?

The Zanussi ZGH62414XS has a depth of 510 mm.

Does the Zanussi ZGH62414XS have a gas hob?

Yes, the Zanussi ZGH62414XS has a gas hob. This means that it uses gas as a fuel source for cooking.

How many cooking zones does the Zanussi ZGH62414XS have?

The Zanussi ZGH62414XS has 4 cooking zones. This provides the user with multiple options for cooking different dishes at the same time.

Does the Zanussi ZGH62414XS have any electric cooking zones?

No, the Zanussi ZGH62414XS does not have any electric cooking zones. This means that all the cooking zones are powered by gas.

Is the Zanussi ZGH62414XS easy to clean?

Yes, the Zanussi ZGH62414XS is easy to clean. This feature makes maintenance and cleaning of the stove hassle-free for the user.

What is the control type of the Zanussi ZGH62414XS?

The control type of the Zanussi ZGH62414XS is rotary. This type of control allows for easy adjustment of the heat levels during cooking.

How do I adjust the power of the gas burners on the Zanussi ZGH62414XS stove?

To adjust the power of the gas burners on the Zanussi ZGH62414XS stove, follow these steps: 1. Remove the knob and the gasket from the burner you want to adjust. 2. Use a thin screwdriver to locate and adjust the bypass screw position (marked as "A" in the manual). 3. If you want to change from natural gas (G20 20 mbar) to liquid gas, fully tighten the bypass screw in. 4. If you want to change from liquid gas to natural gas (G20 20 mbar), undo the bypass screw approximately 1/4 of a turn. 5. Reassemble the gasket and the knob onto the burner. It's important to note that when adjusting the power of the gas burners, you should ensure that the flame does not go out when quickly turning the knob from the maximum position to the minimum position. Please refer to the manual for any additional safety precautions or specific instructions related to adjusting the power of the gas burners on the Zanussi ZGH62414XS stove.

What should I do if the gas burners on the Zanussi ZGH62414XS stove are not igniting?

If the gas burners on the Zanussi ZGH62414XS stove are not igniting, you can follow these steps to troubleshoot the issue: 1. Check if the hob is correctly connected to the electrical supply. Ensure that it is properly plugged in and that the fuse is not blown. 2. Make sure that the burner cap and crown are placed correctly. If they are not aligned properly, it can prevent the flame from igniting. 3. Keep the control knob pushed for equal or less than 10 seconds after lighting the flame. This allows the thermocouple to warm up and ensure a consistent flame. 4. If the flame extinguishes immediately after ignition, it may indicate that the thermocouple is not heated up sufficiently. In this case, try keeping the knob pushed for a longer duration. 5. Check if the burner crown is blocked with food residues. Clean the burner crown and ensure that the injector is not blocked. If you have tried these troubleshooting steps and the issue persists, it is recommended to contact your dealer or an authorized service center for further assistance. Provide them with the necessary details from the rating plate for accurate support.

How do I change the nozzles on the Zanussi ZGH62414XS stove for use in Malta?

To change the nozzles on the Zanussi ZGH62414XS stove for use in Malta, follow these steps: 1. Locate the gas burners on the stove. There are different types of burners, including rapid, semi-rapid, and auxiliary burners. 2. Refer to the table in the manual for the specific nozzle sizes and gas flow rates required for Malta. The table provides information for both natural gas (G20 20 mbar) and LPG (G30/G31 28-30/37 mbar). 3. Turn off the gas supply to the stove and ensure that the burners are cool before proceeding. 4. Remove the burner caps and crowns from the burners that need to be adjusted. 5. Using a suitable tool, carefully unscrew the existing nozzles from the burners. 6. Replace the old nozzles with the appropriate nozzles for Malta, as specified in the table. 7. Ensure that the nozzles are securely tightened but avoid overtightening. 8. Reassemble the burner caps and crowns onto the burners. 9. Turn on the gas supply and perform a leak test to ensure there are no gas leaks. 10. Test the burners by igniting them and checking for proper flame appearance and performance. By following these steps, you can successfully change the nozzles on the Zanussi ZGH62414XS stove for use in Malta.

How do I identify the model of my Zanussi ZGH62414XS stove?

To identify the model of your Zanussi ZGH62414XS stove, you can follow these steps: 1. Locate the rating plate on the stove. It is usually located on the side or back of the appliance. 2. Look for the model number on the rating plate. The model number is a combination of letters and numbers that uniquely identifies your stove. 3. The model number may be labeled as "Model," "Type," or "Product Code" on the rating plate. 4. Note down the complete model number of your Zanussi ZGH62414XS stove. 5. You can also check the user manual or any documentation that came with the stove. The model number is often mentioned in these materials. By following these steps, you can easily identify the model of your Zanussi ZGH62414XS stove. If you have any further questions or need assistance, you can contact the manufacturer or refer to their customer support for more information.

Is the manual of the Zanussi ZGH62414XS available in English?

Yes, the manual of the Zanussi ZGH62414XS is available in English .

Is your question not listed? Ask your question here

No results