Zanussi ZGH62414XS manual

Zanussi ZGH62414XS
7.2 · 1
PDF manual
 · 20 pages
English
manualZanussi ZGH62414XS
should be consulted to determine the requisite air
vent requirements.
For appliances installed in the Republic of Ireland
please refer to the NSAI- Domestic Gas Installation
I.S. 813 Current Editions Table Four.

Location

The hob may be located in a kitchen, a kitchen/
diner or bed sitting room (with a volume greater
than 20 m³), but not in a bathroom or shower room.
The minimum distance combustible material can be
fitted above the hob in line with the edges of the
hob is 400 mm. If it is fitted below 400 mm a space
of 50 mm must be allowed from the edges of the
hob.
For appliances installed in the Republic of Ireland
please refer to NSAI- Domestic Gas Installation I.S
813 Current Edition Section 7- Permitted
Locations of Appliance.
GAS CONNECTION
WARNING! Any gas installation must
be carried out by a GAS SAFE
REGISTER installer.
Please refer to the technical
instructions on how to adjust the hob
to the gas specifications on Malta.
This appliance is certified for Malta.
Make sure that, once the hob is installed, it is easily
accessible for the engineer in the event of a
breakdown.
The manufacturer will not accept liability, should the
above instructions or any of the other safety
instructions incorporated in this instruction booklet
be ignored.
On the end of the shaft, which includes the R 1/2"
threaded elbow, adjustment is fixed so that the
washer is fitted between the components as shown
in the diagram. Screw the parts together without
using excessive force.

A B C

A. End of shaft with nut
B. Washer supplied with the appliance
C. Elbow supplied with the appliance
Connection to the gas supply should be with either
rigid or semi-rigid pipe, i.e. steel or copper.
The connection should be suitable for connecting
to R 1/2 (1/2 BSP male thread).
When the final connection has been made, it is
essential that a thorough leak test is carried out on
the hob and installation.
Make sure that the main connection pipe does not
exert any strain on the hob.
If you use flexible metal pipes make sure that they
agree to ISO 10380 and ISO 10807 standards. Be
careful they do not come in touch with mobile parts
or they are not squeezed. Also be careful when the
hob is put together with an oven.
CAUTION! It is important to install the
elbow correctly, with the shoulder on
the end of the thread, fitted to the hob
connecting pipe.
CAUTION! Failure to ensure the
correct assembly will cause leakage of
gas.
CAUTION! Make sure that the gas
supply pressure of the appliance
obeys the recommended values.

Rigid connection:

Carry out connection by using metal rigid pipes
(copper with mechanical end).
INJECTORS REPLACEMENT
1. Remove the pan supports.
2. Remove the caps and crowns of the burner.
3. With a socket spanner 7 remove the injectors
and replace them with the ones which are
necessary for the type of gas you use (see
table in "Technical Data" chapter).
4. Assemble the parts, follow the same procedure
backwards.
5. Replace the rating plate (it is near the gas
supply pipe) with the one for the new type of
gas supply. You can find this plate in the
package supplied with the appliance.
If the supply gas pressure is changeable or
different from the necessary pressure, you must fit
an applicable pressure adjuster on the gas supply
pipe.
ADJUSTMENT OF MINIMUM LEVEL
To adjust the minimum level of the burners:
1. Light the burner.
2. Turn the knob on the minimum position.
11

Manual

View the manual for the Zanussi ZGH62414XS here, for free. This manual comes under the category stoves and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Zanussi ZGH62414XS or do you need help? Ask your question here

Need help?

Do you have a question about the Zanussi and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Zanussi ZGH62414XS specifications

Below you will find the product specifications and the manual specifications of the Zanussi ZGH62414XS.

The Zanussi ZGH62414XS stove is a gas hob with four cooking zones, all of which are gas-powered. This stove does not have any electric cooking zones. The simmer cooking zone is round in shape, as are the regular and large cooking zones. It is designed for easy cleaning, making maintenance hassle-free. The stove has a width of 594 millimeters, a depth of 510 millimeters, and requires an installation compartment height of 43 millimeters. The Zanussi ZGH62414XS stove offers users the flexibility of four gas cooking zones in various sizes and shapes to accommodate different cooking needs. With its compact design and easy-to-clean features, this gas stove is a practical addition to any kitchen.

General
BrandZanussi
ModelZGH62414XS | ZGH62414XS
Productstove
EAN7332543587384
LanguageEnglish
FiletypeUser manual (PDF), Datasheet (PDF)
Design
Hob typeGas
Number of cooking zones4 zone(s)
Number of gas cooking zones4 zone(s)
Number of electric cooking zones0 zone(s)
Simmer cooking zone shapeRound
Regular cooking zone shapeRound
Large cooking zone shapeRound
Appliance placementBuilt-in
Product colorStainless steel
Pan support materialEnameled
Simmer cooking zone diameter54 mm
Regular cooking zone diameter70 mm
Large cooking zone diameter100 mm
Hob width size60 cm
Top surface type-
Number of simultaneously used cooking zones4
Cooking zone 4 typeSimmer
Cooking zone 1 shapeRound
Cooking zone 3 typeRegular
Cooking zone 1 power2000 W
Cooking zone 3 power sourceGas
Cooking zone 2 positionLeft front
Cooking zone 3 power2000 W
Cooking zone 4 shapeRound
Cooking zone 3 positionRight rear
Cooking zone 4 diameter54 mm
Cooking zone 2 shapeRound
Cooking zone 3 diameter70 mm
Cooking zone 4 power1000 W
Cooking zone 4 positionRight front
Cooking zone 1 diameter70 mm
Cooking zone 1 typeRegular
Cooking zone 4 power sourceGas
Cooking zone 3 shapeRound
Cooking zone 2 typeLarge
Cooking zone 1 positionLeft rear
Cooking zone 2 power sourceGas
Cooking zone 2 power3000 W
Cooking zone 1 power sourceGas
Cooking zone 2 diameter100 mm
Ergonomics
Easy to cleanYes
Control typeRotary
Built-in displayNo
Control positionTop right
Electronic ignitionYes
Child lock-
Weight & dimensions
Width594 mm
Depth510 mm
Height- mm
Installation compartment height43 mm
Installation compartment width550 mm
Installation compartment depth470 mm
Cord length1.1 m
Performance
Number of power levels-
Thermocouple protectionYes
Regular cooking zone2000 W
Simmer cooking zone1000 W
Large cooking zone3000 W
Power
Connected load (gas)8000 W
AC input voltage220 - 240 V
AC input frequency50 - 60 Hz
Connected load (electric)- W
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Zanussi ZGH62414XS below.

Can I use my pans on induction?

Nowadays almost all pans are suitable for induction. You can easily test whether your old pans can also be used on induction by holding a magnet against the bottom of the pan. If the magnet stays on the pan, your old pan is suitable for induction.

How do I reset my induction hob?

Most induction hobs can be reset by disconnecting the hob from power by unplugging it from the power outlet. You will then have to wait at least 60 minutes.

What is a Perilex connection?

A Perilex connection is a special connection that can handle more power than a normal connection. This connection has five holes instead of two and is often used for induction hobs.

Is cooking on induction dangerous?

No, cooking on induction is not dangerous.

What is the height of the Zanussi ZGH62414XS?

The Zanussi ZGH62414XS has a height of - mm.

What is the width of the Zanussi ZGH62414XS?

The Zanussi ZGH62414XS has a width of 594 mm.

What is the depth of the Zanussi ZGH62414XS?

The Zanussi ZGH62414XS has a depth of 510 mm.

Does the Zanussi ZGH62414XS have a gas hob?

Yes, the Zanussi ZGH62414XS has a gas hob. This means that it uses gas as a fuel source for cooking.

How many cooking zones does the Zanussi ZGH62414XS have?

The Zanussi ZGH62414XS has 4 cooking zones. This provides the user with multiple options for cooking different dishes at the same time.

Does the Zanussi ZGH62414XS have any electric cooking zones?

No, the Zanussi ZGH62414XS does not have any electric cooking zones. This means that all the cooking zones are powered by gas.

Is the Zanussi ZGH62414XS easy to clean?

Yes, the Zanussi ZGH62414XS is easy to clean. This feature makes maintenance and cleaning of the stove hassle-free for the user.

What is the control type of the Zanussi ZGH62414XS?

The control type of the Zanussi ZGH62414XS is rotary. This type of control allows for easy adjustment of the heat levels during cooking.

How do I adjust the power of the gas burners on the Zanussi ZGH62414XS stove?

To adjust the power of the gas burners on the Zanussi ZGH62414XS stove, follow these steps: 1. Remove the knob and the gasket from the burner you want to adjust. 2. Use a thin screwdriver to locate and adjust the bypass screw position (marked as "A" in the manual). 3. If you want to change from natural gas (G20 20 mbar) to liquid gas, fully tighten the bypass screw in. 4. If you want to change from liquid gas to natural gas (G20 20 mbar), undo the bypass screw approximately 1/4 of a turn. 5. Reassemble the gasket and the knob onto the burner. It's important to note that when adjusting the power of the gas burners, you should ensure that the flame does not go out when quickly turning the knob from the maximum position to the minimum position. Please refer to the manual for any additional safety precautions or specific instructions related to adjusting the power of the gas burners on the Zanussi ZGH62414XS stove.

What should I do if the gas burners on the Zanussi ZGH62414XS stove are not igniting?

If the gas burners on the Zanussi ZGH62414XS stove are not igniting, you can follow these steps to troubleshoot the issue: 1. Check if the hob is correctly connected to the electrical supply. Ensure that it is properly plugged in and that the fuse is not blown. 2. Make sure that the burner cap and crown are placed correctly. If they are not aligned properly, it can prevent the flame from igniting. 3. Keep the control knob pushed for equal or less than 10 seconds after lighting the flame. This allows the thermocouple to warm up and ensure a consistent flame. 4. If the flame extinguishes immediately after ignition, it may indicate that the thermocouple is not heated up sufficiently. In this case, try keeping the knob pushed for a longer duration. 5. Check if the burner crown is blocked with food residues. Clean the burner crown and ensure that the injector is not blocked. If you have tried these troubleshooting steps and the issue persists, it is recommended to contact your dealer or an authorized service center for further assistance. Provide them with the necessary details from the rating plate for accurate support.

How do I change the nozzles on the Zanussi ZGH62414XS stove for use in Malta?

To change the nozzles on the Zanussi ZGH62414XS stove for use in Malta, follow these steps: 1. Locate the gas burners on the stove. There are different types of burners, including rapid, semi-rapid, and auxiliary burners. 2. Refer to the table in the manual for the specific nozzle sizes and gas flow rates required for Malta. The table provides information for both natural gas (G20 20 mbar) and LPG (G30/G31 28-30/37 mbar). 3. Turn off the gas supply to the stove and ensure that the burners are cool before proceeding. 4. Remove the burner caps and crowns from the burners that need to be adjusted. 5. Using a suitable tool, carefully unscrew the existing nozzles from the burners. 6. Replace the old nozzles with the appropriate nozzles for Malta, as specified in the table. 7. Ensure that the nozzles are securely tightened but avoid overtightening. 8. Reassemble the burner caps and crowns onto the burners. 9. Turn on the gas supply and perform a leak test to ensure there are no gas leaks. 10. Test the burners by igniting them and checking for proper flame appearance and performance. By following these steps, you can successfully change the nozzles on the Zanussi ZGH62414XS stove for use in Malta.

How do I identify the model of my Zanussi ZGH62414XS stove?

To identify the model of your Zanussi ZGH62414XS stove, you can follow these steps: 1. Locate the rating plate on the stove. It is usually located on the side or back of the appliance. 2. Look for the model number on the rating plate. The model number is a combination of letters and numbers that uniquely identifies your stove. 3. The model number may be labeled as "Model," "Type," or "Product Code" on the rating plate. 4. Note down the complete model number of your Zanussi ZGH62414XS stove. 5. You can also check the user manual or any documentation that came with the stove. The model number is often mentioned in these materials. By following these steps, you can easily identify the model of your Zanussi ZGH62414XS stove. If you have any further questions or need assistance, you can contact the manufacturer or refer to their customer support for more information.

Is the manual of the Zanussi ZGH62414XS available in English?

Yes, the manual of the Zanussi ZGH62414XS is available in English .

Is your question not listed? Ask your question here

No results