To deactivate or activate the acoustic signals, press
and hold for approximately 2 seconds touchpads
(B) and (C) at the same time.
ADJUSTMENT OF THE REMAINING LAUNDRY
MOISTURE DEGREE
To change the default degree of the remaining
moisture of the laundry:
1.Press the on/off button to activate the
appliance.
2.Wait approximately 8 seconds.
3.Press and hold buttons (B) and (D) at the same
time.
One of the these indicators comes on:
• the maximum dry laundry
• the more dry laundry
• the standard dry laundry
4.Press the button (F) again and again until the
indicator of the correct level comes on.
5.To confirm the adjustment, press and hold
buttons (B) and (D) at the same time for
approximately 2 seconds.
BEFORE FIRST USE
Before you use the appliance for the first time do
these operations:
•Clean the tumble dryer drum with a moist cloth.
•Start a short programme (e.g. 30 minutes) with
moist laundry.
DAILY USE
START A PROGRAMME WITHOUT DELAY
START
1.Prepare the laundry and load the appliance.
CAUTION! Make sure that when
you close the door, the laundry
does not catch between the
appliance door and the rubber
seal.
2.Press the on/off button to activate the
appliance.
3.Set the correct programme and options for the
type of load.
The display shows the programme duration.
4.Press the Start/Pause touchpad.
The programme starts.
STARTING THE PROGRAMME WITH DELAY
START
1.Set the correct programme and options for the
type of load.
2.Press the delay start button again and again
until the display shows the delay time you want
to set.
You can delay the start of a
programme from a minimum of 60
minutes to a maximum of 20
hours.
3.Press the Start/Pause touchpad.
The display shows the countdown of the delay
start.
When the countdown is completed, the programme
starts.
CHANGE A PROGRAMME
1.Press the on/off button to deactivate appliance
2.Press the on/off button to activate the
appliance.
3.Set the programme.
AT THE END OF THE PROGRAMME
When the programme is completed:
•An intermittent acoustic signal operates.
•The indicator flashes.
•The indicators
Filter and Tank comes on.
•The Start/Pause indicator is on.
The appliance continues to operate with the crease
guard phase for approximately other 30 minutes.
The crease guard phase removes creases from
your laundry.
You can remove the laundry before the crease
guard phase is completed. We recommend, for
better results, that you remove the laundry when the
phase is almost completed or completed.
When the crease guard phase is completed:
•The indicator
is on but does not flash.
•The indicators Filter and Tank comes on.
10
Manual
View the manual for the Zanussi ZDC8203WR here, for free. This manual comes under the category dryers and has been rated by 1 people with an average of a 6.8. This manual is available in the following languages: English. Do you have a question about the Zanussi ZDC8203WR or do you need help? Ask your question here
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Zanussi ZDC8203WR below.
What is a condenser dryer?
A condenser dryer is a dryer in which condensation ends up in a reservoir.
What is a drain dryer?
A drain dryer is a dryer in which the warm air and condensation are drained through a hose.
What is the best thing to do about a smelly dryer?
It is best to wipe the dryer drum with a damp cloth and some lemon cleaner.
There is a burning smell from my dryer, now what?
Check the following: - That the fluff filter is clean. - That the bottom of the dryer is free of dust. - That the drain hose is clean. If the above does not help, a mechanic should be called in.
Is the manual of the Zanussi ZDC8203WR available in English?
Yes, the manual of the Zanussi ZDC8203WR is available in English .
Need help?
Do you have a question about the Zanussi and is the answer not in the manual?
Question and answer
Number of questions: 0