Zanussi ZCV667MWC manual

Zanussi ZCV667MWC
7.2 · 1
PDF manual
 · 24 pages
English
manualZanussi ZCV667MWC
Use small feet on the bottom of appliance to set
the appliance top surface level with other
surfaces.

Anti-tilt protection

Adjust the appliance to the correct height and
put it in the correct area before you attach the
anti-tilt protection.

CAUTION!

Install the anti-tilt protection to
prevent the appliance from falling
under incorrect loads. The anti-tilt
protection only works when the
appliance is put in a correct area.
The anti-tilt protection has two parts (A+B).
You can find the anti-tilt protection (B) on the
right or left side of the rear wall of the appliance.
B
1. Install the anti-tilt protection (A) on the wall.
Make sure that the wall is made of a solid
material. If not, you need to make the wall
sufficiently strong to hold the weight.
Make sure that the surface behind the
appliance is smooth.
2. Put the appliance in the middle of the space
between the cupboards.
If the space is larger than the width of the
appliance, you must adjust the side
measurement.
3. Install the anti-tilt protection (A)
approximately 77 mm below the top surface
of the appliance and 50 mm from the left or
right side of the appliance into the circular
hole on the bracket. Screw it into the wall.
50 mm
77 mm
A
4. Check that the anti-tilt protection (A) fits
minimum 20 mm into the hole in the rear
wall of the appliance (B) when you push the
appliance.

Electrical installation

WARNING!

The manufacturer is not responsible
if you do not follow the safety
precautions from Safety chapters.
This appliance is supplied without a main plug
or a main cable.

Covering terminal board

The recommended cross-section area is six
square millimetres (6 mm²).
When you refit the mains terminal cover,
make sure that the lower tabs are located
inside the bottom edge of the aperture,
before you fix the two screws into the top
edge of the mains terminal cover.
Make sure that the cover is securely
fastened.
To open the cover of terminal board
obey the procedure in opposite
sequence.

Terminal board

Do not remove blanking plates.
Make sure that the links are fitted as shown.
N N N
LL

20 www.zanussi.com

Manual

View the manual for the Zanussi ZCV667MWC here, for free. This manual comes under the category stoves and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Zanussi ZCV667MWC or do you need help? Ask your question here

Need help?

Do you have a question about the Zanussi and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Zanussi ZCV667MWC specifications

Below you will find the product specifications and the manual specifications of the Zanussi ZCV667MWC.

General
BrandZanussi
ModelZCV667MWC
Productstove
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Zanussi ZCV667MWC below.

Can I use my pans on induction?

Nowadays almost all pans are suitable for induction. You can easily test whether your old pans can also be used on induction by holding a magnet against the bottom of the pan. If the magnet stays on the pan, your old pan is suitable for induction.

How do I reset my induction hob?

Most induction hobs can be reset by disconnecting the hob from power by unplugging it from the power outlet. You will then have to wait at least 60 minutes.

What is a Perilex connection?

A Perilex connection is a special connection that can handle more power than a normal connection. This connection has five holes instead of two and is often used for induction hobs.

Is cooking on induction dangerous?

No, cooking on induction is not dangerous.

Is the manual of the Zanussi ZCV667MWC available in English?

Yes, the manual of the Zanussi ZCV667MWC is available in English .

Is your question not listed? Ask your question here

No results