Zanussi ZCG43200BA manual

Zanussi ZCG43200BA
7 · 1
PDF manual
 · 28 pages
English
manualZanussi ZCG43200BA

Hob - Daily use

WARNING!

Refer to Safety chapters.

Ignition of the hob burners

Always light the burner before you
put on the cookware.

WARNING!

Be very careful when you use open
fire in the kitchen environment. The
manufacturer declines any
responsibility in case of the flame
misuse.
1. Turn the knob for the hob to the position
and push it down. When you push the knob,
the spark generator activates automatically.
2. Keep the knob for the hob pushed for equal
or less than 10 seconds to let the
thermocouple warm up. If not, the gas
supply is interrupted.
3. Adjust the flame after it is regular.

WARNING!

Do not keep the knob pushed for
more than 15 seconds. If the burner
does not light after 15 seconds,
release the knob, turn it into the off
position and try to light the burner
again after minimum 1 minute.
If after some tries the burner does
not light, check if the crown and its
cap are in the correct position.
In the absence of electricity you can
ignite the burner without an
electrical device. In this case
approach the burner with a flame,
push the relevant knob down and
turn it to maximum position. Keep
the knob pushed for equal or less
than 10 seconds to let the
thermocouple warm up.
If the burner accidentally goes out,
turn the knob to the off position and
try to light the burner again after
minimum 1 minute.
The spark generator can start
automatically when you switch on
the mains, after installation or a
power cut. It is normal.

Burner overview

A
B
D
G
E
C
F
H
I
A) Burner cap
B) Burner crown
C) Ignition candle
D) Thermocouple
E) Hob
F) Slots
G) Burner body
H) Location peg
I) Hole for the ignition candle

Replacing burner parts

1. Put carefully the burner crown on the burner
body. Let the crown fall freely onto the
body. Do not use force.
Make sure that the hole in the crown is
above the ignition candle.
Make sure that the location pegs are in the
slots in the burner body.
Make sure that you can move the crown a
small distance from side to side.
2. Put the burner cap centrally on top of the
crown.
Make sure that the cap is correctly installed,
with the enamel side up and you can move
the cap from side to side and front to back.
3. Light the burner.

8 www.zanussi.com

Manual

View the manual for the Zanussi ZCG43200BA here, for free. This manual comes under the category stoves and has been rated by 1 people with an average of a 7. This manual is available in the following languages: English. Do you have a question about the Zanussi ZCG43200BA or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Zanussi and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Zanussi ZCG43200BA specifications

Below you will find the product specifications and the manual specifications of the Zanussi ZCG43200BA.

General
BrandZanussi
ModelZCG43200BA | 948 905 039
Productstove
EAN7332543291731
LanguageEnglish
FiletypeUser manual (PDF)
Design
Product typeFreestanding cooker
Product colorBlack
Control typeButtons, Rotary
Cord length1.6 m
Built-in displayYes
Oven
Number of ovens2
Total oven(s) interior capacity111 L
Total oven power- W
Oven power sourceNatural gas
Oven size-
Oven gross capacity77 L
Oven power- W
Noise level- dB
Cool doorYes
Oven net capacity77 L
Oven 2
Oven 2 gross capacity34 L
Oven 2 grillYes
Hob
Hob typeGas
Number of cooking zones4 zone(s)
Number of gas cooking zones4 zone(s)
Hob coverYes
Power
Energy efficiency classA
Energy consumption (conventional)1.73 kWh
Energy consumption (forced convection)- kWh
Energy consumption (conventional)6.23 MJ
Energy consumption (forced convection)- MJ
Weight & dimensions
Width550 mm
Depth600 mm
Height900 mm
Weight56500 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Zanussi ZCG43200BA below.

What is the weight of the Zanussi ZCG43200BA?

The Zanussi ZCG43200BA has a weight of 56500 g.

Can I use my pans on induction?

Nowadays almost all pans are suitable for induction. You can easily test whether your old pans can also be used on induction by holding a magnet against the bottom of the pan. If the magnet stays on the pan, your old pan is suitable for induction.

How do I reset my induction hob?

Most induction hobs can be reset by disconnecting the hob from power by unplugging it from the power outlet. You will then have to wait at least 60 minutes.

What is a Perilex connection?

A Perilex connection is a special connection that can handle more power than a normal connection. This connection has five holes instead of two and is often used for induction hobs.

Is cooking on induction dangerous?

No, cooking on induction is not dangerous.

What is the height of the Zanussi ZCG43200BA?

The Zanussi ZCG43200BA has a height of 900 mm.

What is the width of the Zanussi ZCG43200BA?

The Zanussi ZCG43200BA has a width of 550 mm.

What is the depth of the Zanussi ZCG43200BA?

The Zanussi ZCG43200BA has a depth of 600 mm.

What energy label does the Zanussi ZCG43200BA have?

The Zanussi ZCG43200BA has energy label A.

Is the manual of the Zanussi ZCG43200BA available in English?

Yes, the manual of the Zanussi ZCG43200BA is available in English .

Is your question not listed? Ask your question here

No results