Winora Pedelec manual

Winora Pedelec
7 · 3
PDF manual
 · 252 pages
English
manualWinora Pedelec

Children’s bike Stabilisers

11
3. Assemble them as described in the
manufacturer’s instructions.
4. Attach the first assembled stabiliser to
the axle of the children’s bike, push the
hub axle washer onto the axle and
tighten the cap nut again, observing the
applicable torque (see “Illustr.: Fitting a
stabiliser”).
5. Attach the second assembled stabiliser
to the axle of the children’s bike, push
the hub axle washer onto the axle and
tighten the cap nut again, observing the
applicable torque (see “Illustr.: Fitting a
stabiliser”).
x When tightening the cap nut, ensure
that the rear wheel forms a straight
line with the frame and front wheel.
x When tightening the cap nut, ensure
that the chain is still tensioned.
The stabilisers are height-adjustable.
x Check where the slotted holes for this purpose are positioned on the stabilisers
that you installed. Refer to the fitting information enclosed by the manufacturer.
Both stabilisers should be the same distance from the ground. When holding the
children’s bike straight, the stabilisers should not touch the ground.

6.2 Removing stabilisers

1. Turn both cap nuts until you can remove them from the axle.
2. One by one, remove the hub axle washers and the stabilisers from the axle.
3. Push the hub axle washers onto the axle and tighten the cap nuts, observing the
applicable torque.
4. When tightening the cap nut, ensure that the rear wheel forms a straight line with
the frame and front wheel.
5. When tightening the cap nut, ensure that the chain is still tensioned.
2
3
4
Illustr.: Fitting a stabiliser (example)
1 Rear wheel axle
2 Hub axle washer
3 Cap nut
4 Stabiliser (training wheel)
1

Manual

View the manual for the Winora Pedelec here, for free. This manual comes under the category bicycles and has been rated by 3 people with an average of a 7. This manual is available in the following languages: English. Do you have a question about the Winora Pedelec or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Winora and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Winora Pedelec specifications

Below you will find the product specifications and the manual specifications of the Winora Pedelec.

General
BrandWinora
ModelPedelec
Productbicycle
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Winora Pedelec below.

How do I remove rust from my Winora bicycle?

1. Soak the rusty part in vinegar until completely soaked through. 2. Let the vinegar work on the rust for 24 hours. 3. Remove the rust with a wire brush or aluminium foil.

How much should I exercise as an adult per week?

As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.

How can I adjust the pedal assist level on my Winora Pedelec S-pedelec?

To adjust the pedal assist level on your Winora Pedelec S-pedelec, follow these steps: 1. Familiarize yourself with the pedal assist system on your Winora Pedelec. 2. Locate the control panel or display on your bike that allows you to adjust the pedal assist level. 3. Use the buttons or controls on the panel to increase or decrease the pedal assist level according to your preference. 4. Test ride the bike after adjusting the pedal assist level to ensure it meets your desired level of assistance. 5. If you are unsure about adjusting the pedal assist level, contact your dealer for assistance. Remember to always adjust the pedal assist level safely and according to your riding needs.

How do I adjust the seat height on the Winora Children’s bike?

To adjust the seat height on the Winora Children’s bike, follow these steps: 1. If your bike has a seat post clamp with a clamp bolt: - Hold the saddle firmly and loosen the clamp bolt by turning it anticlockwise. - Pull the seat post out to the desired height, following the minimum insertion depth and pull-out height specifications. - Tighten the clamp bolt by turning it clockwise to secure the seat post clamp. - Check that the saddle is correctly positioned and does not twist. 2. If your bike has a seat post clamp with a quick release: - Hold the saddle firmly and pull the quick-release lever outwards. - Pull the seat post out to the desired height, following the minimum insertion depth and pull-out height specifications. - Secure the seat post clamp by pushing the quick-release lever inwards until it touches the seat tube. - Check that the saddle is correctly positioned and does not twist.

What should I do if the brakes on the Winora Children’s bike feel loose?

To address loose brakes on the Winora Pedelec bicycle, follow these steps: 1. Adjust the brake cable tension in mechanical brakes: - Loosen the lock nut by turning it anticlockwise. - Gradually turn the knurled screw anticlockwise to increase the cable tension until the distance between the brake block holders and the rim is 1–2 millimeters on each side. - Ensure that the brake block holders meet the rim simultaneously on both sides and that the wheel turns smoothly. - Tighten the lock nut by turning it clockwise. 2. Adjust the pressure point in hydraulic brakes: - Locate the pressure point adjustment screw on the brake lever. - Gradually turn the adjustment screw until the distance between the rim and each brake pad is 1–2 millimeters. - Ensure that the brake block holders meet the rim simultaneously on both sides and that the wheel turns smoothly.

Is the manual of the Winora Pedelec available in English?

Yes, the manual of the Winora Pedelec is available in English .

Is your question not listed? Ask your question here

No results