Whirlpool WTW5057LW manual

Whirlpool WTW5057LW
8.7 · 10
PDF manual
 · 21 pages
English
manualWhirlpool WTW5057LW
9

9. Clear water lines

Run water for a few seconds through hoses into a laundry
tub, drainpipe, or bucket to prevent clogs. Water should run
until clear.
Make note of which hose is connected to hot water to help in
attaching hoses to washer correctly.

10. Connect inlet hoses to washer

IMPORTANT: To reduce risk of hose failure, replace the
hoses every 5 years. Record hose installation or replacement
dates for future reference.
Do not overtighten hose or use tape or sealants on valve.
Damage to the valves can result.
Periodically inspect and replace hoses if bulges, kinks,
cuts, wear, or leaks are found.
Attach hot water hose to red hot water inlet valve. Screw
coupling by hand until it is snug. Use pliers to tighten
couplings an additional two-thirds turn. Repeat with cold
water inlet valve.

11. Check for leaks

Turn on water faucets to check for leaks. A small amount of
water may enter washer. It will drain later.

12. Secure drain hose

Secure drain hose to laundry tub leg, drain standpipe, or inlet
hoses for wall standpipe with cable tie.
It is the responsibility of the installer to install and secure the
drain hose into the provided plumbing/drain in a manner that
will avoid the drain hose coming out of or leaking from the
plumbing/drain.

Level Washer

NOTE: Level washer properly to reduce excess noise and
vibration.

13. Check levelness of washer

Move the washer to its final location. Place a level on top
edges of washer. Use side seam as a guide to check
levelness of sides. Check levelness of front using lid, as
shown. Rock washer back and forth to make sure all four feet
make solid contact with floor. If washer is level, skip to
step 15.

View the manual for the Whirlpool WTW5057LW here, for free. This manual comes under the category washing machines and has been rated by 10 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the Whirlpool WTW5057LW or do you need help? Ask your question here

Need help?

Do you have a question about the Whirlpool and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 253
K
Kenneth W.May 2, 2023

When I start my machine, it doesn’t fill or spin. It makes a click sound then try’s to drain and shuts off.

When I start my machine, it doesn’t fill or spin.  It makes a click sound then try’s to drain and shuts off.
zoom-in
View photo
5 comments
E
Emma of manua.lsDecember 21, 2023

The possible issue when the Whirlpool WTW5057LW washing machine does not fill or spin but makes a clicking sound, attempts to drain, and then shuts off could be a problem with the water inlet valve or the drain system. Here are the steps to troubleshoot the issue: 1. Check the water supply: Make sure that the water supply valves are fully open and that there is adequate water pressure. 2. Inspect the water inlet valve: The clicking sound could indicate a faulty water inlet valve. Check if the valve is clogged or malfunctioning. If necessary, replace the water inlet valve. 3. Check the drain system: Ensure that the drain hose is properly connected and not kinked or clogged. Verify that the drain hose is inserted into the standpipe or laundry tub at the correct height to prevent siphoning. If the drain system is not functioning properly, it can cause the machine to shut off. 4. Test the lid switch: The lid switch is a safety feature that prevents the washer from spinning when the lid is open. Make sure that the lid is securely closed and that the lid switch is functioning correctly. If the issue persists after following these steps, it is recommended to contact a professional technician for further assistance.

This answer is automatically generated
N
Nokuthula May 5, 2023

Same as above

S
Sid HoltSeptember 25, 2023

Mine dose the same

S
Susie ChapmanSeptember 7, 2022

Where can I find trouble shooting info for WTW5057LW??? Washer stopped mid cycle . Won’t drain/. Sense /Done/Lid lock lights are flashing

6 comments
E
Emma of manua.lsOctober 25, 2023

You can find troubleshooting information for the Whirlpool WTW5057LW washing machine by visiting the Whirlpool website. Look for the support section and search for the specific model number. This will provide you with the necessary troubleshooting steps to address the issue you mentioned.

This answer is automatically generated
K
K MMay 26, 2024

@Susie Chapman honestly this washer sounds like a nightmare and no appliance should have this many issues. Im so angry i even bought mine now.

S
SteveMarch 2, 2024

@Emma Website is pretty much useless for this model. Just want to know how to access the water pump and cant find any info on that Older models show some info but no help whatsoever. Online chat is worthless also.

K
Kaitlyn February 5, 2024

I’ve just turned my washer on for the first time, and it’s on the soak light, but no water has came in. It’s just spinning ever so often without and water. How do I get the water to come out?

M
Muriel GrenierNovember 15, 2023

When I start my machine, it doesn’t fill or spin. It makes a click sound then try’s to drain and shuts off.

When I start my machine, it doesn’t fill or spin. It makes a click sound then try’s to drain and shuts off.
zoom-in
View photo
C
CarrieMay 11, 2023

I know I was doing a load of laundry and I ended up adding some thing a few minutes into the cycle. Then I closed it and restarted and it never started so I unplugged it hoping to reset it now when I push the button it makes noises but it is not agitating and the water is just stuck in the washer. How can I make this drain and reset it? 512-484-1768

I know I was doing a load of laundry and I ended up adding some thing a few minutes into the cycle. Then I closed it and rest...
zoom-in
View photo
M
Mary Lee JohnsMay 12, 2024

Since my Whirlpool WTW5057LW Top Loading Washing Machine doesn't have any way to indicate loadsize, how do I know how much detergent to add???!

A
Amber haleMay 7, 2024

My washer said code f6e1. I unplugged it, and plugged it back up, now it won't even turn on. I liked up how to get into the settings and i did a factory reset on it, now it won't even turn on or anything. If it's the control board that's bad, what is the model # that it takes?

1 comment
A
Amber haleMay 7, 2024

@Amber hale it is the top load washer with the glass lid. Im not sure what model # my washer is.

W
Willier RobinsonMay 4, 2024

All the lights are on to start the cycle and the sensing fill light are blinking but not doing nothing the light just blinking on and off.

All the lights are on to start the cycle and the sensing fill light are blinking but not doing nothing the light just blinkin...
zoom-in
View photo
M
Michelle May 20, 2024

Why is my twin comforter not in the water or agitating? Any way to add extra water

R
Rheann April 25, 2024

My washer won’t spin out on any cycle except the drain and spin only have had 2days now

The Whirlpool WTW5057LW is a washing machine that is manufactured by Whirlpool, a renowned company in the home appliance industry. It is designed to effectively clean and remove dirt from various types of laundry. The washing machine has a capacity of X pounds, allowing users to wash a decent amount of clothes in a single cycle. Equipped with a X-horsepower motor, the Whirlpool WTW5057LW provides sufficient power to agitate clothes and remove stubborn stains. It features X wash cycles, including delicate, normal, and heavy-duty, to cater to different washing needs. The machine also offers X water temperature settings, allowing users to customize the washing process according to their preferences and garment requirements. The Whirlpool WTW5057LW is designed to be user-friendly, with a control panel that is easy to navigate. It has a clear and bright display, which makes it convenient for users to select their desired settings. The washing machine also features a programmable timer, which enables users to delay the start of a washing cycle to fit their schedule. In terms of energy efficiency, the Whirlpool WTW5057LW has a X-star energy rating, ensuring that it consumes less electricity and water compared to traditional washing machines. This not only helps users save on utility bills but also contributes to reducing environmental impact. Overall, the Whirlpool WTW5057LW is a reliable and durable washing machine that offers a range of features to effectively clean clothes.

General
BrandWhirlpool
ModelWTW5057LW
Productwashing machine
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF), Safety instructions (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Whirlpool WTW5057LW below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

Why is the washing machine not starting?

Make sure the power cord is securely plugged into a grounded outlet and try pressing the "Start" button again. Also, ensure that the lid is closed properly, as the machine will not start if the lid is open.

Why is the water not filling the machine?

Check that the water supply valves are fully open. Additionally, inspect the water inlet hoses for any kinks or clogs that might be blocking water flow. It's recommended to use a cold water supply for optimal performance.

How do I adjust the water level for different load sizes?

To adjust the water level, simply rotate the "Load Size" selector knob to the desired setting. Larger load sizes may require higher water levels, while smaller loads can be washed with lower water levels. Remember to distribute the clothes evenly in the drum.

Why is the washing machine not draining properly?

First, ensure that the drain hose is not kinked or blocked. If the drain hose is clear, check if the drain pump filter is clogged with lint or debris. Clean the filter if necessary. Additionally, verify that the drain hose is installed correctly at the appropriate height, as incorrect positioning may impact draining.

How do I resolve excessive vibration during the spin cycle?

Check if the washer is level by adjusting the feet underneath. Make sure all four feet are in firm contact with the floor. Uneven load distribution can also cause excessive vibration, so try redistributing clothes inside the drum. Finally, avoid overloading the machine, as this can disrupt balance and result in increased vibration.

Is the manual of the Whirlpool WTW5057LW available in English?

Yes, the manual of the Whirlpool WTW5057LW is available in English .

Is your question not listed? Ask your question here

No results