Whirlpool WRS325SDHZ manual

Whirlpool WRS325SDHZ
9.3 · 3
PDF manual
 · 64 pages
English
manualWhirlpool WRS325SDHZ
44

Évaporateur double (sur certains

modèles)

Certains modèles sont équipés d’un double système
d’évaporation séquentiel, composé de deux évaporateurs
distincts pour les compartiments de réfrigération et de
congélation.
La double évaporation engendre un taux d’humidité supérieur, ce
qui contribue à ralentir la détérioration des aliments dans le
réfrigérateur et à améliorer leur qualité et leur fraîcheur dans le
congélateur, la brûlure de congélation étant moins vive. En outre,
le double système d’évaporation contribue à éviter que les odeurs
de nourriture présentes dans le réfrigérateur ne se transfèrent aux
glaçons du congélateur.
REMARQUE : Le double système d’évaporation est toujours
activé lorsque le réfrigérateur fonctionne. Il n’est pas nécessaire
d’appuyer sur un quelconque bouton pour l’activer.

Distributeurs d’eau et de glaçons

Pour savoir comment les distributeurs d’eau et de glaçons,
consulter le guide en ligne des fonctions des « distributeurs côte à
côte du réfrigérateur ». Guide des caractéristiques.
REMARQUES :
Brancher sur une alimentation en eau potable uniquement.
Le système de distribution ne fonctionne pas lorsque la porte
du réfrigérateur ou du congélateur est ouverte.
Attendre 24 heures pour que le réfrigérateur et l’eau
refroidissent.
Prévoir un délai de 24 heures pour la production du premier lot
de glaçons. Jeter les trois premiers lots de glaçons produits.
Attendre 72 heures pour que la production de glaçons soit
complète.
Sur certains modèles, l’écran d’affichage sur le tableau de
commande du distributeur s’éteint automatiquement et entre
au mode « Veille » lorsque les boutons de commande et les
plaques du distributeur n’ont pas été utilisées pendant au
moins 2 minutes. Le fait d’appuyer une fois sur un bouton de
commande alors que l’appareil est au mode « veille » réactive
uniquement l’écran d’affichage, sans modifier les réglages.

Rinçage du circuit d’eau

De l’air piégé dans le système de distribution d’eau peut faire
dégoutter le distributeur d’eau. Après avoir raccordé le
réfrigérateur à une source d’alimentation en eau ou remplacé le
filtre à eau, vidanger le circuit d’eau. Le fait de rincer le système
de distribution d’eau évacue l’air de la canalisation et du filtre et
conditionne le filtre à eau.
REMARQUE : Pendant l’évacuation de l’air du système, de l’eau
peut gicler du distributeur.
1. En utilisant un récipient robuste, appuyer sur la plaque du
distributeur d’eau pendant 5 secondes, puis relâcher la plaque
pendant 5 secondes.
2. Répéter l’étape 1 jusqu’à ce que l’eau commence à couler.
3. Une fois que l’eau commence à couler, continuer d’appuyer et
de relâcher la plaque du distributeur (appui pendant
5 secondes, relâchement pendant 5 secondes) jusqu’à ce
qu’un total de 3 gal (12 L) ait été distribué.
Un amorçage supplémentaire peut s’avérer nécessaire dans
certains domiciles.

Distributeur d’eau

IMPORTANT :
Distribuer au moins 1 pte (1 L) d’eau chaque semaine pour
maintenir un approvisionnement en eau fraîche.
La diminution du débit en provenance du distributeur peut être
causée par une faible pression en eau.
Avec le filtre à eau retiré, verser l’équivalent d’une (1) tasse
d’eau (237 mL). Si l’équivalent d’une (1) tasse d’eau est
distribué en 8 secondes ou moins, cela signifie que la pression
en eau alimentant le réfrigérateur répond au critère minimal.
S’il faut plus de 8 secondes à la machine pour distribuer
l’équivalent d’une (1) tasse d’eau, cela signifie que la pression
en eau alimentant le réfrigérateur est inférieure au niveau
recommandé. Voir les sections « Spécifications de
l’alimentation en eau » ou « Dépannage » en ligne pour des
suggestions sur la marche à suivre.

Machine à glaçons et bac

d’entreposage

Prévoir un délai de 24 heures pour la production du premier lot
de glaçons. Jeter les trois premiers lots de glaçons produits.
La qualité des glaçons dépend de la qualité de l’eau fournie à
la machine à glaçons. Éviter de connecter la machine à
glaçons à une alimentation en eau adoucie. Les produits
chimiques adoucisseurs d’eau (comme le sel) peuvent
endommager certaines pièces de la machine à glaçons et
entraîner une mauvaise qualité de glaçons. Si l’alimentation en
eau adoucie ne peut être évitée, s’assurer que l’adoucisseur
d’eau fonctionne bien et qu’il est bien entretenu.
Ne pas utiliser un objet pointu pour briser les glaçons dans le
bac d’entreposage. Cette action peut endommager le récipient
à glaçons et le mécanisme du distributeur.
Ne pas garder quoi que ce soit sur le dessus ou dans la
machine à glaçons ou dans le bac d’entreposage.

Style 1

Mise en marche/arrêt de la machine à glaçons :
On ne peut accéder au commutateur marche/arrêt, situé sur la
paroi gauche de la porte du congélateur, qu’une fois le bac
d’entreposage à glaçons retiré. Voir la section suivante pour des
instructions sur le retrait du bac.
Pour mettre en marche la machine à glaçons, tourner le
commutateur à la position On (marche) (vers le haut).
Pour un arrêt manuel de la machine à glaçons, tourner le
commutateur à la position Off (arrêt) (vers le bas).
REMARQUE : La machine à glaçons comporte un système
d’arrêt automatique pour éviter le surremplissage du bac
d’entreposage pendant un fonctionnement normal. Au fur et à
mesure de la production, les glaçons remplissent le bac
d’entreposage. Les glaçons soulèvent le bras de commande
métallique jusqu’à ce qu’il atteigne la position Off (arrêt) (haut).
Lorsque le bac d’entreposage est plein, la machine à glaçons
arrête automatiquement la production de glaçons, mais le
commutateur On/Off (marche/arrêt) reste à la position On
(marche).

View the manual for the Whirlpool WRS325SDHZ here, for free. This manual comes under the category refrigerators and has been rated by 3 people with an average of a 9.3. This manual is available in the following languages: English. Do you have a question about the Whirlpool WRS325SDHZ or do you need help? Ask your question here

Need help?

Do you have a question about the Whirlpool and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 56
T
Trichel VaheyApril 18, 2023

The freezer door will not close tightly. It looks like it’s too tight on the hinge side but cannot understand how to align it. The refrigerator side door closes firmly

The freezer door will not close tightly. It looks like it’s too tight on the hinge side but cannot understand how to align it...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 19, 2023

To adjust the freezer door on the Whirlpool WRS325SDHZ refrigerator, please follow these steps: 1. Open both doors of the refrigerator. 2. Check the levelness of the floor where the rear side of the refrigerator will rest. If the refrigerator is not leveled, adjust or add shims on the flooring to create a leveled floor for the rear side wheels. A leveled rear side prevents the refrigerator cabinet from forming a twist. 3. Use a bubble level to check the levelness of the refrigerator. Place the bubble level on top of the refrigerator or on its side to ensure it is level. 4. Use a 3/8" nut driver to turn the leveling screws located on both sides of the refrigerator. Depending on the uneven floor conditions, you may need to turn one or both screws to the right or left several times to raise or lower the refrigerator. 5. Close both doors and check that they close easily. If not, turn both screws to the right to raise the refrigerator by tilting it more to the back until the doors close easily.

This answer is automatically generated
D
Denise MetcalfMay 26, 2024

The temperature settings bars including the check marks have been illuminated since I’ve had the refrigerator which I purchased in April. While cleaning the screen the check marks no longer appear and the bars go off after a few months minutes. Is this normal?

S
Samantha h.May 14, 2024

My fridge and freezer are no longer getting cold. It's not even a month old. Everything is getting soggy . Who do I call?

L
L SHERWOODOctober 16, 2023

There is a red light that shows H2O but I cannot find what or where I am to look for place to correct.

There is a red light that shows H2O but I cannot find what or where I am to look for place to correct.
zoom-in
View photo
1 comment
D
DIANNA BAILEYJanuary 28, 2024

@L SHERWOOD

A
Annette C. WlliamsFebruary 7, 2023

There is a red light that shows H2O but I cannot find what or where I am to look for place to correct.

1 comment
F
Felix Bruno October 26, 2023

Where do u press to turn the reset for the filter light off

M
Maggie May 10, 2023

There is a red light that shows H2O but I cannot find what or where I am to look for

1 comment
J
JoshApril 17, 2024

@Maggie This means the water filter should be replaced. It is timer-based, so you can reset the timer by holding the "Light" and "Ice type" buttons for a few seconds.

J
JohnJuly 22, 2023

I accidentally got the parts of the drawers mixed up what page do I find to reinstall the drawers back in place

T
Tom TrippJuly 27, 2023

Just received delivery of WR325SDHZ08 side-by-side refrigerator. In the last hour the interior has only gotten 4 degrees (F) cooler. Is this normal or should I worry?

T
TomAugust 11, 2023

The top light bulb in my wrs325sdhz08 freezer is not working. Can it be replaced and if so, how is it done

S
SamirSeptember 18, 2023

Coloque la temperatura del refrigerador lo menos Frio y aún sigue congelando mis artículos frescos. Que debo hacer?

The Whirlpool WRS325SDHZ is a refrigerator that offers ample storage space and reliable performance. With its spacious 24.6 cubic feet capacity, you can easily store all your groceries and beverages. The refrigerator features adjustable glass shelves, allowing you to customize the layout to suit your needs and accommodate larger items. It also has adjustable gallon door bins, providing convenient storage for milk jugs and other large containers. The WRS325SDHZ includes two humidity-controlled crispers, designed to keep your fruits and vegetables fresh for longer. It also features a temperature-controlled full-width drawer, which is ideal for storing deli meats and cheeses. The refrigerator is equipped with LED interior lighting, ensuring that the contents are well-illuminated, making it easy to find what you need. In terms of functionality, the WRS325SDHZ features a through-the-door ice and water dispenser, providing chilled water and ice cubes on demand. The dispenser also includes a water filter, ensuring that you have clean and fresh-tasting water. In terms of design, the refrigerator has a sleek stainless steel exterior, adding a touch of modernity to your kitchen. It features a fingerprint-resistant finish, keeping the appliance looking clean and polished. With its Energy Star certification, the WRS325SDHZ is designed to be energy-efficient, helping you to conserve electricity and reduce your utility bills. In summary, the Whirlpool WRS325SDHZ is a spacious and reliable refrigerator, offering customizable storage options, advanced features such as an ice and water dispenser, and a sleek design.

General
BrandWhirlpool
ModelWRS325SDHZ | WRS325SDHZ
Productrefrigerator
LanguageEnglish
FiletypeUser manual (PDF), Installation Guide (PDF), Quickstart Guide (PDF), Datasheet (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Whirlpool WRS325SDHZ below.

How do I prevent drops from forming on the glass plates of my fridge?

There may be various causes for this, it is recommended to check the following: - Is the drain hole free of dirt? - Does the refrigerator door close properly? - Is the refrigerator not too full so that air can circulate properly? - Is the temperature not set below 5 degrees?

What do I do about a smelly fridge?

A common method for solving the problem of a smelly fridge is to pour vinegar into the drain and temporarily place a cup of vinegar in the fridge.

How much free space does my fridge need?

A minimum of 2.5 centimetres of free space around the fridge is needed to ventilate properly.

What does R-410A stand for?

R-410A is a refrigerant used in machines that cool to zero degrees Celsius.

Why is my refrigerator not cooling properly?

There could be various reasons for this issue, such as a dirty condenser coil, improper temperature settings, or a faulty temperature control. Troubleshooting these areas can help resolve the cooling problem.

What should I do if my refrigerator is making strange noises?

Unusual noises coming from your refrigerator could indicate a faulty fan motor, a clogged drain, or even a loose component. Inspecting and potentially repairing these areas can help eliminate the noises.

How can I prevent frost buildup in my freezer?

Frost buildup can occur due to a damaged door gasket, frequent door openings, or improper temperature settings. Checking and replacing the gasket if needed, minimizing door openings, and adjusting the temperature can help prevent frost accumulation.

How do I resolve ice dispenser issues?

If your ice dispenser is not working correctly, it might be due to a clogged water line, an improperly installed water filter, or a faulty dispenser motor. Checking and addressing these potential issues can restore the ice dispenser's functionality.

Why is water leaking from my refrigerator?

Water leakage can be caused by a blocked defrost drain, a cracked water inlet valve, or a faulty water filter. Investigating and resolving these issues can help stop the water leakage and maintain a properly functioning refrigerator.

Is the manual of the Whirlpool WRS325SDHZ available in English?

Yes, the manual of the Whirlpool WRS325SDHZ is available in English .

Is your question not listed? Ask your question here

No results