Whirlpool WRF767SDHZ manual

Whirlpool WRF767SDHZ
8.2 · 1
PDF manual
 · 84 pages
English
manualWhirlpool WRF767SDHZ
W11402361B
W11402373B-SP
French Door Bottom Mount Quick Start Guide

OPERATING INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS, located in your appliance’s Owner’s Manual, before operating this appliance.
IMPORTANT: Before operating this appliance, make sure it has been properly installed according to the
appliance’s Owner’s Manual.
The controls are located above the external dispenser.
NOTE: The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode
when the control buttons and dispenser paddles have not been used for 2 minutes or more. Press any
control button to reactivate the display screen. The home screen will appear as shown.
For your convenience, your refrigerator and freezer controls are preset at the factory. When you first install
your refrigerator, make sure that the controls are still set to the recommended set points. The factory
recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.
IMPORTANT:
Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the
refrigerator has cooled completely, your food may spoil.
NOTE: Adjusting the set points to a colder than recommended setting will not cool the compartments
any faster.
If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be
sure they are not blocked before adjusting the controls.
The recommended settings should be correct for normal household refrigerator use. The controls are
set correctly when milk or juice is as cold as you like and when ice cream is firm.
NOTE: Areas such as a garage, basement, or porch may have higher humidity or extreme
temperatures. You may need to adjust the temperature away from the recommended settings to
accommodate for these conditions.
Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are
made.
TEMPERATURE SET POINTS
1. Press and hold Temp for 3 seconds to activate Temperature mode.
NOTE: To view temperature in degrees Celsius, press the Light button, under Units, when adjust mode
is activated. To return the display setting to Fahrenheit, press the Light button again.
When Temperature mode is activated, press Temp to toggle between Fridge and Freezer. The display
will show the temperature set point of the selected compartment and temperature adjusting information
will appear on the display screen.
Recommended Refrigerator Temperature
Recommended Freezer Temperature
Fridge set point range: 33°F to 45°F (0°C to 7°C) Freezer set point range: -5°F to 5°F (-21°C to -15°C)
2. When Temperature mode is activated, press Temp to select the Refrigerator or Freezer zone. The
display will show the temperature set point of the selected compartment as shown.
3. Press Lock to raise the set point, or press Options to lower the set point.
4. When you have finished viewing (and adjusting if desired) the refrigerator set point, press Temp, under
Select Zone, to change the display to show the freezer set point. When the zone has been changed,
“Freezer” appears on the display screen.
5. Press the Lock button to raise the set point, or press the Options button to lower the set point.
When adjusting temperature set points, use the following chart as a guide.
CONDITION TEMPERATURE ADJUSTMENT
Refrigerator too cold Refrigerator setting higher
Refrigerator too warm Refrigerator setting lower
Freezer too cold Freezer setting higher
Freezer too warm / too little ice Freezer setting lower
Save/Confirm Temperature Settings
When you have finished adjusting both the refrigerator and freezer set points, press Fast Ice to confirm
and to save the settings.
NOTE: To exit Temperature mode without saving changes, press the Ice/Water button under Back at any
time, or allow about 60 seconds of inactivity. The temperature mode will turn off automatically and return to
the normal screen.
OPTIONS
Press the Options button to open the Options menu and select among Filter Status or Vacation mode.
Press the Ice/Water button under “Back” at any time to return to the Home screen.
COOLING ON/OFF
Your refrigerator and freezer will not cool when cooling is turned off.
To turn cooling off, press and hold the Lock and Fast Ice buttons at the same time for 3 seconds. The
Cooling Off icon will blink seven times and then remain lit.
IMPORTANT:
To avoid unintentionally locking the dispenser or changing other settings, press both buttons at exactly
the same time.
When cooling is off, the dispenser paddles and all controls except, Lock and Fast Ice, are disabled.
Press and hold Lock and Fast Ice for 3 seconds again to turn cooling back on.
FAST ICE
The Fast Ice feature assists with temporary periods of heavy ice use by increasing ice production. Once
selected, Fast Ice will remain on for 24 hours unless manually turned off.
To turn on the Fast Ice feature, press Fast Ice. When the feature is on, the Fast Ice
icon will appear on the dispenser display screen.
To manually turn off the Fast Ice feature, press Fast Ice again. When the feature has
been turned off, the Fast Ice icon will disappear from the dispenser display
WATER FILTER STATUS
Press Options on the control panel to launch the Options menu. Press Options, under Filter Status, again
to display the percentage of filter life remaining (from 99% to 0%). Press Ice/Water under Back, to return to
the Normal screen.
The water filter status lights will let you know when to change your water
filter.
Yellow: Order Filter—it is almost time to change the water filter.
While you are dispensing water, “Order Filter” will blink seven times
and sound an alert tone three times.
Red: Replace Filter—Replace the water filter. While you are
dispensing water, “Replace Filter” will blink seven times and an alert
tone will sound three times.
NOTE: “Replace Filter” will remain illuminated if a filter is not installed
or is installed incorrectly.
Reset the water filter status tracking feature. After you replace the disposable filter with a new filter,
closing the filter compartment door will automatically reset the filter status tracking feature.
VACATION MODE
In Vacation Mode, the freezer will defrost less often to conserve energy.
To turn on Vacation mode, press the Options button to access the Options menu, then
press Lock, under Vacation, to activate the feature. When the feature is on, the Vacation
icon will appear on the dispenser display screen as shown.
To turn off Vacation Mode, press the Options button to access the Options menu, then
press Lock to turn off the feature. The Vacation icon will disappear, and the screen will
display the settings as they were before Vacation Mode was turned on.
NOTES:
During the first hour after Vacation Mode is turned on, opening and closing the refrigerator door will not
affect the setting. After 1 hour has passed, opening and closing the refrigerator door will turn off
Vacation Mode.
While in Vacation Mode, if Fast Ice is turned on or the Door Ajar alarm sounds, Vacation Mode will be
canceled.
DISPENSER LIGHT
When you use the dispenser, the lights will turn on automatically.
To turn on the light when you are not dispensing, press Light to toggle through the
following choices in a continuous loop:
OFF (default): The dispenser light is off.
ON: The dispenser light remains on at 100% brightness.
DIM: The dispenser light remains on at 50% brightness.
ON DIM
The dispenser lights are LEDs that cannot be changed. If it appears that your dispenser lights are not
working, see online “Troubleshooting” for more information.
DISPENSER LOCK
The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children
and pets.
NOTE: The lock feature does not shut off power to the refrigerator, to the ice
maker, or to the dispenser light. It simply deactivates the controls and dispenser
lever. To turn off the ice maker, see the “Ice Maker and Storage Bin” section in the
Owner’s Manual.
Press and hold Lock for 3 seconds to lock the dispenser.
Press and hold Lock a second time to unlock the dispenser.
The display screen indicates when the dispenser is locked.
LOCKED
UNLOCKED

Online Ordering Information

For detailed installation instruction and maintenance information, winter storage, and transportation tips,
please see the Owner’s Manual included with your appliance.
For information on any of the following items, a full cycle guide, warranty, detailed product dimensions, or
for complete instructions for use and installation, please visit https://www.whirlpool.com/owners, or in
Canada https://www.whirlpool.ca/owners. This may save you the cost of a service call. However, if you
need to contact us, use the information listed below for the appropriate region.
United States:
1–800–253–1301
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022–2692
Canada:
1–800–807–6777
Whirlpool Brand Home Appliances
Customer eXperience Centre
200–6750 Century Ave.
Mississauga, Ontario L5N 0B7

SAVE THESE INSTRUCTIONS

View the manual for the Whirlpool WRF767SDHZ here, for free. This manual comes under the category freezers and has been rated by 1 people with an average of a 8.2. This manual is available in the following languages: English. Do you have a question about the Whirlpool WRF767SDHZ or do you need help? Ask your question here

Need help?

Do you have a question about the Whirlpool and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 74
L
Linda Mix-SpearsJune 7, 2022

Why is ice & snow crystals building up on top left area around box in the back left corner of the freezer, in bin and door.

Why is ice & snow crystals building up on top left area around box in the back left corner of the freezer, in bin and door.
zoom-in
View photo
2 comments
E
Emma of manua.lsDecember 21, 2023

The freezer of the Whirlpool WRF767SDHZ has an ice maker located on the left side of the refrigerator door. The ice cubes are ejected into the ice storage bin, which is also on the left side of the refrigerator door. To address the buildup of ice and snow crystals in the top left area, around the box located in the back left corner of the freezer, inside the bin and the door, you can follow these steps: 1. Push up on the latch on the left side of the ice compartment to open the door. 2. Turn on the ice maker by moving the switch to the "on" position. If necessary, you can manually turn off the ice maker by moving the switch to the "off" position. 3. Close the ice compartment door. If the issue persists, you can try removing and replacing the ice storage bin: 1. Insert your fingers into the hole at the base of the bin and squeeze the latch to release the bin from the compartment. 2. Lift the storage bin up and pull it straight out. 3. Replace the storage bin inside the ice compartment and push down to ensure it is securely in place.

This answer is automatically generated
J
Janice PrivetteApril 15, 2023

Can’t get ice bin out of refrig . Release latch does depress but something is keeping it from full release to allow for pulling out bin

A
Alan BernierMay 1, 2023

Wha tis the procedure to align the doors on a WRF767SDHZ? Both doors tend to swing open fully and “bounce” against the hinge stops. The door are of slightly different heights, (right door slightly higher) and the left door protrudes slightly farther out at the top of the door but lines up nicely at the bottom. Model WRF767SDHZ S/N KB4404026 The unit was purchased in October, and remained in its original packaging until installation this week. The left door also also has a slight bind when closing, it must be pushed lightly fornthe latch to engage. Also, the

Wha tis the procedure to align the doors on a WRF767SDHZ?
Both doors tend to swing open fully and “bounce” against the hinge...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 25, 2023

To align the doors on the Whirlpool WRF767SDHZ freezer, follow these steps: 1. Open both doors fully. 2. Locate the hinge stops on the sides of the freezer. 3. Gently push the doors towards the hinge stops until they stop moving. 4. Check the alignment of the doors. If one door is higher or protrudes farther out, proceed to the next step. 5. To adjust the height of the doors, locate the hinge adjustment screws on the top of the freezer. 6. Use a screwdriver to loosen the screws slightly. 7. Adjust the height of the doors by lifting or lowering them as needed. 8. Once the doors are aligned, tighten the hinge adjustment screws securely. 9. Close the doors and check if they swing open fully without bouncing against the hinge stops. 10. If the left door has a slight bind when closing, check the latch mechanism for any obstructions or misalignment. 11. Adjust the latch mechanism if necessary to ensure smooth closing and proper engagement.

This answer is automatically generated
L
Laura HaleSeptember 3, 2023

The sliding shelf slid all the way back and locked in place! This happened while we were cleaning the shelves before installing. How do we free up that sliding portion of the shelf?

The sliding shelf slid all the way back and locked in place! This happened while we were cleaning the shelves before installi...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 18, 2023

To free up the moving part of the shelf on the Whirlpool WRF767SDHZ freezer, follow these steps: 1. Take out any items from the shelf. 2. Slide the shelf straight out until it reaches the stopping point. 3. Depending on your model, lift either the back or front of the shelf beyond the stopping point. Pull the shelf out completely. To put the shelf back, follow these steps: 1. Slide the back of the shelf into the track on the wall of the cabinet. 2. Guide the front of the shelf into the shelf track. Make sure to slide the shelf in all the way.

This answer is automatically generated
B
Beth JordanMarch 8, 2023

How do I see what the temperature inside is? I only see how to see the set points.

1 comment
E
Emma of manua.lsDecember 16, 2023

To check the current temperature inside the Whirlpool WRF767SDHZ freezer, follow these steps: 1. Make sure the refrigerator is plugged in and turned on. 2. Open the freezer door. 3. Look for a digital display panel on the front of the freezer. 4. On the display panel, you should see the current temperature of the freezer. 5. Take note of the displayed temperature.

This answer is automatically generated
E
Edward FarfagliaDecember 7, 2020

How do I access the led light control?

2 comments
E
Emma of manua.lsOctober 24, 2023

To access the control of the LED light on the Whirlpool WRF767SDHZ freezer, follow these steps: 1. On models with options buttons and Measured Fill, press the Options button to access the Options mode. 2. Press the Lock button to reset the LED light indicator. 3. Press the Measured Fill button to confirm the reset. 4. Once the system is reset, the "Order" and "Replace" icons will disappear from the display.

This answer is automatically generated
M
Martha TaborMay 25, 2022

it will not stop making a chiming noise

B
Beth BaderJanuary 20, 2024

my pull out drawer is off the track - how can I get it out - won't lift off the track

my pull out drawer is off the track - how can I get it out - won't lift off the track
zoom-in
View photo
D
Deanne RichardsonMay 2, 2024

the refrigerator alarm is going off and won't stop. The doors are all shut. The light on the inside flickers on and off. What does this mean? The control panel on the front won't work and the ice and water won't come out.

J
Julie PearsonMay 1, 2024

three questions 1. I lifted a flap at top back of my fridge. For a filter? Now I can't get it down. 2. My door ice is not dispensing 3. It doesn't seem the fridge is cold enough Less than a year old

1 comment
B
BestFridgeMay 25, 2024

@Julie Pearson 1. The flap in the back is for the air filter (carbon filter). You have to install it by pressing it in. The water filter is on the top right inside the fridge. 2 & 3. Are the vents blocked? How long has the freezer been running? What is the temp set to?

D
DeniseApril 25, 2024

Will the top ice bin fill with ice after the bottom one Is full or do you have to shutt off the bottom one to get ice on top???

The Whirlpool WRF767SDHZ is a freezer that is designed to offer efficient and reliable cooling for your food storage needs. With its sleek and modern design, it can seamlessly blend in with any kitchen decor. Featuring a spacious interior, this freezer offers ample storage space to accommodate your frozen food items. It comes with adjustable shelves and bins, allowing you to customize the storage layout according to your preference. The freezer also includes a pull-out drawer, making it easier to access and organize your food items. Equipped with advanced cooling technology, the WRF767SDHZ freezer provides consistent and even cooling throughout the entire unit. This ensures that your food stays fresh and frozen for longer periods of time. It also includes a frost-free defrost feature, eliminating the need for manual defrosting. With its energy-efficient design, this freezer helps to minimize electricity consumption and reduce energy costs. It is also equipped with sound-reducing technology, making it operate quietly without disturbing your daily activities. The WRF767SDHZ freezer is built with high-quality materials, ensuring its durability and longevity. It comes with a reliable warranty, providing you with peace of mind and assurance of its performance. Overall, the Whirlpool WRF767SDHZ is a reliable and efficient freezer that offers ample storage space and advanced cooling technology, making it a great addition to any kitchen.

General
BrandWhirlpool
ModelWRF767SDHZ
Productfreezer
EAN883049464336
LanguageEnglish
FiletypeUser manual (PDF), Use and Care Manual (PDF), Quickstart Guide (PDF), Warranty information (PDF), Datasheet (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Whirlpool WRF767SDHZ below.

How often should I defrost my freezer?

It is recommended to completely defrost your freezer at least once every six months.

How should I transport a freezer?

A freezer must be transported upright at all times. It is very bad for a freezer to be transported on its side as oil from the compressor can end up in the evaporator.

What do I do about a smelly freezer?

A commonly used method is to temporarily place a cup of vinegar in the freezer.

Why is my freezer not cooling properly?

A possible reason for insufficient cooling could be a clogged air vent, hindering proper airflow. Make sure the vents are clear and unobstructed.

How can I prevent frost buildup in my freezer?

Frost buildup might occur due to gaps or leaks in the freezer seal. Inspect the door gasket for any damage and make sure it is sealing tightly when closed.

What should I do if my freezer is making loud noises?

Noises can result from various factors, such as a faulty evaporator fan motor or ice buildup. Check for any ice accumulation and ensure the fan motor is functioning correctly.

How do I change the water filter in my freezer?

To change the water filter, locate the filter location inside the freezer and gently twist counterclockwise to release it. Replace it with a compatible new filter by twisting it clockwise until secure.

Why is my freezer leaking water onto the floor?

A potential cause of water leakage is a blocked or frozen defrost drain. Inspect the drain to ensure it is clear of debris and ice. Cleaning the drain using hot water can help resolve the issue.

Is the manual of the Whirlpool WRF767SDHZ available in English?

Yes, the manual of the Whirlpool WRF767SDHZ is available in English .

Is your question not listed? Ask your question here

No results