View the manual for the Whirlpool WRF560SMY here, for free. This manual comes under the category refrigerators and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Whirlpool WRF560SMY or do you need help? Ask your question here
| Brand | Whirlpool |
| Model | WRF560SMY |
| Product | refrigerator |
| Language | English |
| Filetype | Use and Care Manual (PDF), Energy label (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Whirlpool WRF560SMY below.
There may be various causes for this, it is recommended to check the following: - Is the drain hole free of dirt? - Does the refrigerator door close properly? - Is the refrigerator not too full so that air can circulate properly? - Is the temperature not set below 5 degrees?
A common method for solving the problem of a smelly fridge is to pour vinegar into the drain and temporarily place a cup of vinegar in the fridge.
A minimum of 2.5 centimetres of free space around the fridge is needed to ventilate properly.
R-410A is a refrigerant used in machines that cool to zero degrees Celsius.
To troubleshoot if the Whirlpool WRF560SMY refrigerator is not cooling properly, follow these steps: 1. Check the electrical supply: Ensure that the power cord is plugged into a grounded 3-prong outlet. Do not use an extension cord. Verify if there is power to the outlet by plugging in a lamp. 2. Reset circuit breaker or replace blown fuses: If the refrigerator is not operating, check if a circuit breaker has tripped or if any fuses have blown. Reset the circuit breaker or replace the blown fuses if necessary. If problems persist, contact an electrician. 3. Verify the controls: Make sure that the controls are turned on. Refer to the manual for instructions on using the controls. 4. Allow time for cooling: If the refrigerator has been recently installed or if a large amount of warm food has been added, allow 24 hours for the refrigerator to cool completely. Adjusting the temperature controls to the coldest setting will not cool the compartments quicker. 5. Check for obstructions: Ensure that the refrigerator door or freezer drawer is fully closed and not ajar. Keep food and containers from blocking the door. If the issue persists after following these troubleshooting steps, it is recommended to contact Whirlpool customer service for further assistance.
To troubleshoot if the Whirlpool WRF560SMY refrigerator is making unusual noises, follow these steps: 1. Identify the type of noise: Listen carefully to determine the specific type of noise the refrigerator is making. Common noises include buzzing, hissing, popping, rattling, or sizzling. 2. Check for obstructions: Ensure that the refrigerator is not touching any walls or cabinets, as this can cause vibrations and noise. Make sure that items placed on top of the refrigerator are not causing any rattling or banging sounds. 3. Level the refrigerator: Use a level to check if the refrigerator is properly leveled. Adjust the leveling screws and lower the leveling foot firmly against the floor to stabilize the refrigerator. 4. Check the water lines: If the noise is coming from the water dispenser, check if the water lines are properly connected and not vibrating against the refrigerator cabinet. Secure any loose water lines or tubing. 5. Contact customer service: If the unusual noise persists or if you are unsure about the cause, it is recommended to contact Whirlpool customer service for further assistance. They can provide specific troubleshooting steps or schedule a service appointment if needed. Remember, it is normal for refrigerators to make certain intermittent noises, such as the sound of the compressor running or the contraction/expansion of the inside walls. However, if the noise is excessive or concerning, it is best to address the issue promptly.
To troubleshoot if the Whirlpool WRF560SMY refrigerator is leaking water, follow these steps: 1. Check the water supply: Ensure that the refrigerator is properly connected to a water supply and that the water supply shutoff valve is fully open. If the refrigerator is connected to a reverse osmosis water filtration system, check if it is affecting the water pressure. 2. Inspect the water lines: Look for any kinks or obstructions in the water source line that may be restricting water flow. Straighten the water line if necessary. 3. Verify proper installation: If the refrigerator has been recently installed, flush and fill the water system to remove any air from the lines. Make sure that the water dispenser wire/tube assembly is properly connected at the top of the refrigerator door. 4. Check the water filter: If a water filter is installed, remove it and operate the dispenser to see if the water flow increases. A clogged or incorrectly installed water filter may cause leakage. 5. Ensure proper closure: Close the refrigerator door firmly to ensure it is fully closed. If the doors were recently removed, make sure the water line connections are fully tightened. If the issue persists or if you are unsure about the cause of the leakage, it is recommended to contact Whirlpool customer service for further assistance.
To troubleshoot if the Whirlpool WRF560SMY refrigerator's ice maker is not producing ice, follow these steps: 1. Check the water supply: Ensure that the refrigerator is properly connected to a water supply and that the water supply shutoff valve is fully open. If the refrigerator is connected to a reverse osmosis water filtration system, check if it is affecting the water pressure. 2. Verify the ice maker is turned on: Make sure the ice maker is turned on. Refer to the manual for instructions on how to turn on the ice maker. 3. Allow time for ice production: After installing the ice maker or making any changes, allow 24 hours for the ice maker to begin producing ice. It may take up to 3 days for the ice container to be completely filled. 4. Check the ice storage bin: Ensure that the ice storage bin is properly positioned under the ice maker. Make sure the arm on the ice maker is in the "on" position. 5. Clean the ice storage bin: Wash the ice storage bin with mild soap and warm water to remove any residue or buildup that may be affecting ice production. If the issue persists after following these troubleshooting steps, it is recommended to contact Whirlpool customer service for further assistance.
To troubleshoot if the Whirlpool WRF560SMY refrigerator is not dispensing water, follow these steps: 1. Check the water supply: Ensure that the refrigerator is properly connected to a water supply and that the water supply shutoff valve is fully open. If the refrigerator is connected to a reverse osmosis water filtration system, check if it is affecting the water pressure. 2. Verify the doors are closed: Make sure that the refrigerator doors are fully closed. If the doors are not closed properly, the water dispenser may not operate. 3. Check for kinks or obstructions: Inspect the water source line for any kinks or obstructions that may be restricting water flow. Straighten the water line if necessary. 4. Verify the dispenser is not in sleep mode: The dispenser control panel may enter "sleep" mode if not used for 2 minutes or more. Press any control button to reactivate the display screen and make changes to the settings if needed. 5. Flush the water system: If the refrigerator has been recently installed or if the water filter has been changed, flush the water system to remove any air or debris that may be affecting water flow. If the issue persists after following these troubleshooting steps, it is recommended to contact Whirlpool customer service for further assistance.
Yes, the manual of the Whirlpool WRF560SMY is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Whirlpool and is the answer not in the manual?
Question and answer
Number of questions: 0