Whirlpool WRF535SWHZ manual

Whirlpool WRF535SWHZ
8.4 · 5
PDF manual
 · 75 pages
English
manualWhirlpool WRF535SWHZ
20

PERFORMANCE DATA SHEETS

Interior Water Filtration System

Model UKF8001AXX-750 Capacity 750 Gallons (2839 Liters)

This system has been tested according to NSF/ANSI Standards 42, 53, 401 and CSA B483.1 for the reduction of the substances listed
below. The concentration of the indicated substances in water entering the system was reduced to a concentraion less than or equal
to the permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42, 53, 401 and CSA B483.1.
Substance Reduction
Aesthetic Effects
NSF
Reduction
Requirements
Average
Inuent
Inuent Challenge
Concentration
Maximum
Efuent
Average
Efuent
Minimum%
Reduction
Average%
Reduction
Chlorine Taste/Odor
Particulate Class I*
50% reduction
85% reduction
2.00 mg/L
14,000,000 #/mL
2.0 mg/L ± 10%
At least
10,000 particles/mL
0.06 mg/L
370,000 #/mL**
0.050625 mg/L
196,666 #/mL
97.00%
97.40%
97.52%
99.00%
Contaminant
Reduction
NSF Reduction
Requirements
Average Inuent Inuent Challenge
Concentration
Maximum
Efuent
Average
Efuent
Minimum%
Reduction
Average%
Reduction
Lead: @ pH 6.5
Lead: @ pH 8.5
0.010 mg/L
0.010 mg/L
0.150 mg/L
0.150 mg/L
0.15 mg/L ± 10%
0.15 mg/L ± 10%
< 0.001 mg/L
< 0.001 mg/L
< 0.001 mg/L
< 0.001 mg/L
>99.30%
>99.30%
>99.30%
>99.30%
Mercury: @ pH 6.5
Mercury: @ pH 8.5
0.002 mg/L
0.002 mg/L
0.006 mg/L
0.0059 mg/L
0.006 mg/L ± 10%
0.006 mg/L ± 10%
0.0005 mg/L
0.0018 mg/L
0.0003 mg/L
0.00073 mg/L
91.70%
69.20%
95.00%
88.10%
Benzene 0.005 mg/L 0.0133 mg/L 0.015 mg/L ± 10% 0.0005 mg/L 0.0005 mg/L 96.10% 96.30%
p-Dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >99.80% >99.80%
Carbofuran 0.040 mg/L 0.0753 mg/L 0.08 mg/L ± 10% 0.027 mg/L 0.008 mg/L 64.60% 73.45%
Toxaphene 0.003 mg/L 0.015 mg/L 0.015 ± 10% < 0.001 mg/L < 0.001 mg/L >93.3% >93.3%
Atrazine 0.003 mg/L 0.0102 mg/L 0.009 mg/L ± 10% 0.0027 mg/L 0.00105 mg/L 76.30% 89.40%
Asbestos >99% 126.5 MF/L 107 to 108 bers/L
††
< 0.17 MF/L < 0.17 MF/L >99.99% >99.99%
Live Cysts
Turbidity
>99.95%
0.5 NTU
122,500 #/L
10.5 NTU
50,000/L min.
11 ± 1 NTU
< 1 #/L
0.30 NTU
< 1 #/L
0.125 NTU
>99.99%
97.30%
>99.99%
98.80%
Lindane 0.0002 mg/L 0.0019 mg/L 0.002 ± 10% < 0.00016 mg/L 0.000035 mg/L 91.80% 97.90%
Tetrachloroethylene 0.005 mg/L 0.015 mg/L 0.015 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >96.6% >96.6%
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.78 gpm (2.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F ± 5°F (20°C ± 3°C).
It is essential that operational, maintenance, and lter replacement
requirements be carried out for the product to perform as advertised.
The disposable water lter should be replaced at least every 6
months.
The lter monitor system measures the amount of water that passes
through the lter and alerts you to replace the lter. When 90% of
the lter’s rated life is used, the yellow (Order) light comes on. When
100% of the lter’s rated life is used, the red (Replace) light comes
on, and it is recommended that you replace the lter. For models
without lter status lights, replace the lter every 6 months. Use
replacement lter model UKF8001. 2015 suggested retail price of
$44.99 U.S.A./ $49.95 Canada. Prices are subject to change without
notice.
The product is for cold water use only.
Do not use with water that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after the system.
Systems certied for cyst reduction may be used on disinfected
waters that may contain lterable cysts.
*Class I particle size: >0.5 to <1 um
**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
These contaminants are not necessarily in your water supply
Performance may vary based on local water conditions.
Fibers greater than 10 um in length
Based on the use of Cryptosporidium parvum oocysts
®
NSF is a registered trademark of NSF International.
Refer to the “Water Filtration System” section for the Manufacturer’s
name and telephone number.
Refer to the “Warranty” section for the Manufacturer’s limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply
Water Pressure
Water Temperature
Service Flow Rate
Potable City or Well
35 - 120 psi (241 - 827 kPa)
33° - 100°F (1° - 38°C)
0.78 gpm (2.9 L/min.) @ 60 psi
System tested and certied by NSF International against NSF/ANSI
Standard 42, 53, 401 and CSA B483.1 for the reduction of
contaminants specied on the Performance Data Sheet.

View the manual for the Whirlpool WRF535SWHZ here, for free. This manual comes under the category refrigerators and has been rated by 5 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Whirlpool WRF535SWHZ or do you need help? Ask your question here

Need help?

Do you have a question about the Whirlpool and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 108
I
Ivan CastroOctober 11, 2021

My Electronic Temperature Control panel is off and i'm unable to change settings. Freezer appears to be working, but refrigerator is not. What can I do to troubleshoot?

My Electronic Temperature Control panel is off and i'm unable to change settings.  Freezer appears to be working, but refrige...
zoom-in
View photo
2 comments
E
Emma of manua.lsDecember 19, 2023

To troubleshoot the Electronic Temperature Control panel on the Whirlpool WRF535SWHZ refrigerator, follow these steps: 1. Check the power: Make sure the refrigerator is plugged in correctly and turned on. If the control panel is completely off, check the power supply to ensure it is functioning properly. 2. Check the temperature settings: Verify that the temperature settings on the control panel are set correctly. The recommended settings for normal household refrigerator use are pre-set at the factory. If needed, adjust the temperature settings using the control panel. 3. Check for blockages: Ensure that the air vents in the refrigerator and freezer compartments are not blocked. Blocked vents can affect temperature distribution and prevent proper cooling. Clear any obstructions that may be blocking the vents. 4. Allow time for cooling: After adjusting the temperature settings or making any changes, wait at least 24 hours for the refrigerator to cool completely before adding food. Adding food before the refrigerator has cooled completely may affect its performance. 5. Check for temperature issues: If the refrigerator compartment is not cooling properly while the freezer compartment is working fine, it could indicate a problem with the cooling system. In this case, it is recommended to contact customer service for further assistance.

This answer is automatically generated
K
Ken May 14, 2024

Can i changethr light brightness inside refrigerator?

H
HeatherSeptember 5, 2022

Trying to figure out how to properly install/adjust the crisper shelf onto the mounts The mounts appear fixed and shelf isnt wide enough to reach both to sit properly…is there supposed to be a “cover” to each mount that then allows the shelf to snap over this?

Trying to figure out how to properly install/adjust the crisper shelf onto the mounts

The mounts appear fixed and shelf is...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 21, 2023

The manual does not mention a "cover" on each mount that allows the shelf to snap into place. Therefore, it appears that the mounts are fixed and the shelf should fit correctly without any additional covers.

This answer is automatically generated
J
Jamie JohnstonOctober 14, 2023

Frost and ice build up in the freezer section It’s a brand new fridge what is the solution ? Settings are ref 7 freezer 4

Frost and ice build up in the freezer section
It’s a brand new fridge what is the solution ?
Settings are ref 7 freezer 4
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 18, 2023

To resolve the problem of frost and ice buildup in the freezer section of the Whirlpool WRF535SWHZ refrigerator, you can follow these steps: 1. Check the door seal: Make sure the freezer door is closing properly and the door seal is clean and intact. A faulty door seal can allow warm air to enter the freezer, leading to frost and ice buildup. 2. Check the temperature settings: Ensure that the freezer temperature is set to the recommended level. In this case, the current setting of 4 is appropriate. Adjusting the temperature too low can cause excessive frost and ice formation. 3. Avoid overloading the freezer: Do not overload the freezer with too much food. Overpacking the freezer can restrict airflow and lead to frost buildup. 4. Allow space for airflow: Ensure that there is enough space around the freezer for proper airflow. Avoid blocking the vents inside the freezer and maintain proper ventilation around the appliance. 5. Regularly defrost the freezer: If frost and ice buildup occur frequently, it may be necessary to manually defrost the freezer. Follow the manufacturer's instructions on how to defrost the freezer properly.

This answer is automatically generated
J
Joan TemplinDecember 16, 2020

My bottom freezer has iced over. How do I defrost it?

3 comments
E
Emma of manua.lsOctober 24, 2023

To defrost the bottom freezer of the Whirlpool WRF535SWHZ refrigerator, please follow these steps: 1. Press the freezer (+) touch pad repeatedly until "OFF" appears on the freezer display to turn off the refrigerator. Wait a few seconds for the refrigerator to shut off. Both compartments will stop cooling. 2. Take out all the food from the refrigerator and pack all frozen food in dry ice. 3. Empty the ice bin. 4. Turn off the temperature control(s). 5. Unplug the refrigerator. 6. Thoroughly clean, wipe, and dry the freezer to remove any ice buildup.

This answer is automatically generated
M
Margaret KingMay 24, 2021

How do I remove freezer draws?

B
Bruce BollingerMay 20, 2023

water filter is leaking

A
AdrianaJanuary 9, 2022

What is the correct temperature for the refrigerator and freezer?

1 comment
E
Emma of manua.lsOctober 24, 2023

The manual for the Whirlpool WRF535SWHZ refrigerator provides the recommended temperature range for optimal performance and cooling. The preferred temperature range for the refrigerator and freezer is mentioned as 60°F to 90°F (15°C to 32°C). However, the manual does not specify the exact temperature settings for the refrigerator and freezer compartments. To adjust the temperature settings, follow these steps: 1. Press the refrigerator or freezer temperature control touch pad. 2. Use the (+) or (-) touch pads to adjust the temperature set point. 3. Wait for 24 hours between adjustments for the temperature to stabilize. It is important to avoid adjusting the temperature controls more than one setting at a time, except when initially turning on the refrigerator. This will allow the temperature to stabilize properly.

This answer is automatically generated
B
Barbara BishopJune 5, 2024

How can I clean inside the edges of the shelves. I do not see a way to remove the glass and I have juice that has seeped into the edge.

J
joni TulenchikJune 11, 2024

My refrigerator has a terrible smell and I have cleaqned the enitre inside but cannot get rid of the smell

M
MaryJune 19, 2021

Freezer bin has a divider that I want to remove. How can I?

Freezer bin has a divider that I want to remove. How can I?
zoom-in
View photo
This message has been automatically translated
1 comment
E
Emma of manua.lsOctober 25, 2023

To remove the divider in the freezer compartment of the Whirlpool WRF535SWHZ refrigerator, follow these steps: 1. Refer to Graphic 4 to remove the freezer handle assembly. Keep all parts together. 2. Move the door stop to the opposite side of the freezer door according to Graphic 3. 3. Attach the handle to the opposite side of the freezer door. 4. Tighten all screws and set the door aside. 5. Firmly grasp the base grille with both hands and pull it towards you to remove it. 6. Place a shim under the bottom front edge of the refrigerator cabinet to take the weight off the roller brackets. 7. Remove the screws from both roller brackets as shown in Graphic 6. 8. Remove the hinge plate located behind the roller bracket and move it to the opposite side of the refrigerator. Move the hinge pin and shim to the outside hole on the hinge plate. Refer to Graphic 6. 9. Depending on the type of door: - For standard doors: Follow the instructions and graphics provided. - For freezer drawer models: Assemble the parts for the bottom hinge and top hinge as shown. Adjust the door so that the bottom of the refrigerator door aligns with the top of the freezer drawer. Tighten all screws. - For freezer door models: Make sure the hinge plate is securely fastened behind the roller bracket and that the hinge pin is inserted into the outside hole. Fully tighten all roller bracket screws. Remove the shim placed under the front edge of the refrigerator cabinet. Replace the freezer door. Assemble the parts for the center hinge and top hinge. Adjust the doors so that the bottom of the refrigerator door aligns with the top of the freezer door. Tighten all screws. - For French doors: Assemble the parts for the top hinges and bottom hinges. Align each door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws. 10. Reconnect the wiring plug on top of the left-hand side refrigerator door. 11. Replace the top hinge covers. 12. Check all holes to ensure that hole plugs and screws are in place. Reinstall the top hinge cover. 13. Replace the base grille. 14. Plug the refrigerator into a grounded 3-prong outlet.

This answer is automatically generated
C
Caroline VoelkersFebruary 12, 2024

photos related to the door seal question. there is one of these brackets on the top and bottom of the hinge seal, the bottom one is off its bracket. no idea how.

photos related to the door seal question. there is one of these brackets on the top and bottom of the hinge seal, the bottom ...
zoom-in
View photo

The Whirlpool WRF535SWHZ is a refrigerator that offers ample storage and convenience for homeowners. It has a total capacity of 25 cubic feet, with 18 cubic feet dedicated to refrigeration and 7 cubic feet in the freezer. The freezer includes a pull-out drawer and adjustable shelves to maximize usable space. The refrigerator features spill-proof glass shelves, two humidity-controlled crispers, and a deli drawer for storing meat and cheeses. The LED lighting illuminates the interior, making it easy to find what you're looking for. This refrigerator also features an exterior water and ice dispenser. It has a built-in filter that removes impurities, ensuring a clean and fresh taste. The dispenser also offers measured water fill and a lockout feature to prevent accidental dispensing. Additionally, the Whirlpool WRF535SWHZ has a stainless steel finish that is smudge-resistant, making it easy to clean and maintain. Its electronic temperature control allows for precise adjustments to maintain optimal food storage conditions. The refrigerator also features energy-efficient technology, which helps lower utility bills while reducing its carbon footprint. Overall, the Whirlpool WRF535SWHZ is a reliable and functional refrigerator suitable for any household.

General
BrandWhirlpool
ModelWRF535SWHZ
Productrefrigerator
EAN883049442068
LanguageEnglish
FiletypeUser manual (PDF), Use and Care Manual (PDF), Warranty information (PDF), Datasheet (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Whirlpool WRF535SWHZ below.

How do I prevent drops from forming on the glass plates of my fridge?

There may be various causes for this, it is recommended to check the following: - Is the drain hole free of dirt? - Does the refrigerator door close properly? - Is the refrigerator not too full so that air can circulate properly? - Is the temperature not set below 5 degrees?

What do I do about a smelly fridge?

A common method for solving the problem of a smelly fridge is to pour vinegar into the drain and temporarily place a cup of vinegar in the fridge.

How much free space does my fridge need?

A minimum of 2.5 centimetres of free space around the fridge is needed to ventilate properly.

What does R-410A stand for?

R-410A is a refrigerant used in machines that cool to zero degrees Celsius.

Why is my refrigerator not cooling properly?

It is possible that the temperature settings are incorrect. Make sure the refrigerator is set to a colder temperature and check if the vents inside the refrigerator are not blocked.

How can I adjust the temperature settings of my refrigerator?

To adjust the temperature settings, locate the control panel inside the refrigerator. Use the temperature control buttons to increase or decrease the desired temperature.

Why is there water leaking from my refrigerator?

This could be due to a clogged or frozen defrost drain. Check the drain located at the bottom of the refrigerator and remove any debris or ice buildup.

How do I change the water filter in my refrigerator?

Locate the water filter compartment inside the refrigerator and follow the instructions to replace the water filter. Remember to turn off the water supply before replacing the filter.

What should I do if my refrigerator is making unusual noises?

Unusual noises may be caused by a variety of factors, including a loose or vibrating component. Check if the refrigerator is level and ensure that it is not touching any nearby objects. If the noise persists, contact a service technician for further assistance.

Is the manual of the Whirlpool WRF535SWHZ available in English?

Yes, the manual of the Whirlpool WRF535SWHZ is available in English .

Is your question not listed? Ask your question here

No results