Whirlpool AWE 2127 manual

Whirlpool AWE 2127
6.8 · 1
PDF manual
 · 2 pages
English
manualWhirlpool AWE 2127

5019 312 11079

Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration (hrs : min)
without “Rapid” with “Rapid”
Cotton / Antibacterial 95 6.0 53* 1.91 2:05
Cotton ** 60 6.0 48 1.02 4:00 2:30
Cotton ** 60 3.0 35 0.76 2:10 ***
Cotton 40 6.0 48 0.65 2:50 2:00
Cotton ** 40 3.0 35 0.57 2:00 ***
Synthetics 60 3.0 50* 0.90 2:05 1:14
Synthetics 40 3.0 40 0.50 1:50 0:59
Delicates 40 1.5 50 0.55 0:45
Daily load 40 3.0 40 0.45 1:00
Speed 15' 30 3.0 30 0.15 0:15
Wool 40 1.0 55 0.55 0:45
Handwash 40 1.0 40 0.55 0:35
Lingerie 30 1.0 40 0.40 0:31
1. Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergent and eventual additives as described on
the front page and in your Instructions for use.
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The lamp next to the
“Start(Pause)” button flashes.
CONSUMPTION DATA
PREPARATION OF THE WASH CYCLE
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to “Cancel (Reset) a running programme before
the end”.
“Rapid” button
Enables quicker washing by shortening the
programme duration.
Recommendable for small loads or only lightly soiled
laundry.
“Intensive rinse” button
The amount of water is increased to ensure a more
intensive rinse.
This option is particularly suitable for areas with very
soft water, washing baby linen and people with skin
allergies.
“Rinse hold” button
The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
This option is particularly recommended for the
“Synthetics”, “Daily load” and “Delicates”
programmes.
It is useful if you want to postpone spinning to a later
time, or if you want to drain out only.
If you select “Rinse hold”, do not leave items to
soak for too long.
As soon as the appliance stops in the rinse hold, the
“Rinse hold” lamp of the sequence indicator lights up
and the lamp next to the “Start(Pause)” button flashes.
Terminate the “Rinse hold” option:
Press the “Start(Pause)” button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME START
Open the tap and press the “Start(Pause)” button.
The indication lamp next to the “Start(Pause)” button
lights up. The programme sequence indicator shows the
current programme phase, running from left to right
through Wash, Rinse, Spin/Drain. When the programme
phrase is finised, the corresponding indication goes out.
Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
PROGRAMME END
All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start(Pause)” button to pause the
programme. The light flashes.
2. Select the new programme, any options and another
spin speed if you want.
3. Press the “Start(Pause)” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end. Press the “Reset” button for at least 3 seconds.
Any existing water is drained out before the door can be
opened.
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
“Cold wash” button
Water is heated only up to 20°C.
Suitable for delicate laundry items with wash
temperature recommendation of max. 30°C on the
care label.
Selectable only on the lowest temperature
step of each programme.
“Prewash” button
Only for heavily soiled loads (for example sand,
granular dirt). Increases the cycle time by
approximately 20 min.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the
home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type
of wash. Water and energy consumption refer to the default setting of the programmes; selecting special options or modifying spin
speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that
time (see also “Troubleshooting Guide” in your Instructions for Use).
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Reference programmes for Energy Label.
*** Automatic adaption of programme duration after detection of wash load.
If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
programme and press the “Start(Pause)” button.
Variable spin” button
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only.
FAILURE INDICATIONS
In a case of any failures of irregularities, consult the
“Troubelshooting Guide” in Instruction for Use.
“Service”
Lighting up of the “Service” indication can be caused by a
fault in an electrical component.
Water tap closed”
The washing machine has no or insufficient water supply;
the water tap might be closed or the water inlet hose
kinked.
“Clean pump”
Waste water is not pumped out. The drain hose may be
kinked or the filter must be cleaned (see “Cleaning the
filter” in your Instructions for Use).

Manual

View the manual for the Whirlpool AWE 2127 here, for free. This manual comes under the category washing machines and has been rated by 1 people with an average of a 6.8. This manual is available in the following languages: English. Do you have a question about the Whirlpool AWE 2127 or do you need help? Ask your question here

Need help?

Do you have a question about the Whirlpool and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Whirlpool AWE 2127 specifications

Below you will find the product specifications and the manual specifications of the Whirlpool AWE 2127.

General
BrandWhirlpool
ModelAWE 2127
Productwashing machine
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Whirlpool AWE 2127 below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

Is the manual of the Whirlpool AWE 2127 available in English?

Yes, the manual of the Whirlpool AWE 2127 is available in English .

Is your question not listed? Ask your question here

No results