Whirlpool AFG 6352 AP manual

Whirlpool AFG 6352 AP
9.6 · 1
PDF manual
 · 4 pages
English
manualWhirlpool AFG 6352 AP

INSTRUCTIONS FOR USE

GB
1. Lid handle.
2. Lock (if provided).
3. Seal.
4. Divider (if provided).
5. Defrost water drain plug.
6. Control panel.
7. Side motor cooling grille.
8. Upper edge.
9. Condenser (located at the rear)
INSTALLATION
Please refer to the chapter "BEFORE USING THE
APPLIANCE".
Unpack the appliance.
Remove the 4 protection pieces inserted between
lid and appliance.
Ensure that the defrosting water drainage plug (if
provided) is correctly positioned (5).
For best operation of the appliance and in order to
avoid damage when the lid is opened, leave a space of
at least 7 cm from the rear wall and 7 cm at the sides.
Fit the accessories (if provided).
1. Temperature adjustment thermostat.
2. Red LED (if provided) : Indicates that the appliance
temperature is not sufficiently low.
3. Green LED (if provided): indicates that the appliance is on.
4. Yellow/orange illuminated button (if provided):
activates/deactivates the fast freeze function. It lights up
when the fast freeze function is active.
The exact configuration of the controls may vary
according to the model.
Switching on the appliance
The appliance is factory set for optimum operation at a
temperature of -18°C.
Plug in the appliance.
The green LED lights up (if provided).
Also the red LED (if provided) will switch on because the
temperature inside the appliance is not yet sufficiently low
for food storage. The red LED will normally switch off
within the first six hours after the appliance is switched on.
After connecting the appliance to the mains supply and when
the optimal temperature has been reached (this phase takes
about 1 hour during which the lid will not open), ensure that
the fast freeze button is not pressed (the yellow LED, if
provided, is off).
Place food inside the product only when the red LED (if
provided) has switched off.
Thanks to the efficient lid seal, the appliance lid will not re-
open easily immediately after closing. Wait a few minutes
before re-opening the lid of the appliance.
Temperature Adjustment
Use the thermostat to select the ideal storage temperature. To
adjust the internal temperature, proceed as follows:
Turn the thermostat knob to 1 for a storage temperature
that is less cold.
Turn the thermostat knob to 6 / for a colder storage
temperature.
For partial loads, or when the load indicator is below the "e"
symbol inside the appliance, it is advisable to move the
thermostat to the lower position (on "e", if present on the
thermostat scale)

CO Big

Climatic Class Amb. T. (°C) Amb. T. (°F)
SN From 10 to 32 From 50 to 90
N From 16 to 32 From 61 to 90
ST From 16 to 38 From 61 to 100
T From 16 to 43 From 61 to 110

View the manual for the Whirlpool AFG 6352 AP here, for free. This manual comes under the category freezers and has been rated by 1 people with an average of a 9.6. This manual is available in the following languages: English. Do you have a question about the Whirlpool AFG 6352 AP or do you need help? Ask your question here

Need help?

Do you have a question about the Whirlpool and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandWhirlpool
ModelAFG 6352 AP | AFG6352AP
Productfreezer
LanguageEnglish
FiletypeUser manual (PDF)
Power
AC input voltage220 - 240 V
Energy usage0.61 kWh/24h
Annual energy consumption223 kWh
A+
Connected load90 W
AC input frequency50 Hz
Performance
Noise level40 dB
Star rating4*
Freezer gross capacity230 L
Freezer net capacity225 L
Freezing capacity24 kg/24h
Design
Product colorWhite
Appliance placementBuilt-in
Product typeUpright freezer
Custom panel-readyYes
Door panel includedNo
Weight & dimensions
Weight51000 g
Height85 mm
Width1120 mm
Depth660 mm
Ergonomics
Cord length1.7 m
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Whirlpool AFG 6352 AP below.

What is the weight of the Whirlpool AFG 6352 AP?

The Whirlpool AFG 6352 AP has a weight of 51000 g.

How often should I defrost my freezer?

It is recommended to completely defrost your freezer at least once every six months.

How should I transport a freezer?

A freezer must be transported upright at all times. It is very bad for a freezer to be transported on its side as oil from the compressor can end up in the evaporator.

What do I do about a smelly freezer?

A commonly used method is to temporarily place a cup of vinegar in the freezer.

What is the height of the Whirlpool AFG 6352 AP?

The Whirlpool AFG 6352 AP has a height of 85 mm.

What is the width of the Whirlpool AFG 6352 AP?

The Whirlpool AFG 6352 AP has a width of 1120 mm.

What is the depth of the Whirlpool AFG 6352 AP?

The Whirlpool AFG 6352 AP has a depth of 660 mm.

What is the energy usage of the Whirlpool AFG 6352 AP?

The energy usage of the Whirlpool AFG 6352 AP is 0.61 kWh/24h. This means that it has a relatively low energy consumption, making it cost-effective and energy-efficient for the user.

How does the Whirlpool AFG 6352 AP's annual energy consumption compare to other freezers?

The Whirlpool AFG 6352 AP has an annual energy consumption of 223 kWh. This places it in the moderate range compared to other freezers, neither exceptionally high nor low in terms of energy consumption.

What is the noise level of the Whirlpool AFG 6352 AP?

The Whirlpool AFG 6352 AP has a noise level of 40 dB. This is considered relatively quiet, ensuring a peaceful environment for the user.

What is the freezing capacity of the Whirlpool AFG 6352 AP?

The Whirlpool AFG 6352 AP has a freezing capacity of 24 kg/24h. This means it can freeze a substantial amount of food in a day, providing convenience and flexibility for the user.

Does the Whirlpool AFG 6352 AP come with a door panel included?

No, the Whirlpool AFG 6352 AP does not come with a door panel included. However, it is custom panel-ready, allowing users to personalize its appearance to match their kitchen décor.

How do I properly position the Whirlpool AFG 6352 AP freezer during installation?

To properly position the Whirlpool AFG 6352 AP freezer during installation, follow these steps: 1. Unpack the appliance and remove the 4 protection pieces inserted between the lid and the appliance. 2. Ensure that the defrosting water drainage plug is correctly positioned. 3. Leave a space of at least 7 cm from the rear wall and 7 cm at the sides to allow for proper operation and to avoid damage when opening the lid. 4. Fit any accessories that are provided with the freezer. By following these steps, you can ensure that the Whirlpool AFG 6352 AP freezer is properly positioned during installation.

Why is the red LED indicator not switching off after plugging in the appliance?

The red LED indicator of the Whirlpool AFG 6352 AP freezer may not switch off after plugging in the appliance due to various reasons. Here are some troubleshooting steps to address this issue: 1. Check for a power failure: Ensure that there is no power outage or interruption in the electrical supply to the appliance. 2. Verify if defrosting is in progress: If the freezer is in the defrosting cycle, the red LED indicator may remain on until the cycle is complete. Wait for the defrosting process to finish and check if the LED turns off. 3. Ensure the appliance lid is properly closed: Make sure that the lid of the freezer is securely closed. If the lid is not closed properly, it can prevent the LED indicator from switching off. 4. Check the positioning of the appliance: Ensure that the freezer is not positioned near a heat source, as this can affect the operation of the appliance and cause the LED indicator to remain on. 5. Verify the thermostat setting: Check if the thermostat is set to the correct temperature. Adjust the thermostat if necessary and monitor if the LED indicator switches off. 6. Clean the ventilation grille and condenser: Dust and debris accumulation on the ventilation grille and condenser can affect the performance of the appliance. Clean these components regularly to ensure proper functioning. By following these troubleshooting steps, you can address the issue of the red LED indicator not switching off after plugging in the Whirlpool AFG 6352 AP freezer.

How do I adjust the internal temperature of the Whirlpool AFG 6352 AP freezer?

To adjust the internal temperature of the Whirlpool AFG 6352 AP freezer, follow these steps: 1. Locate the temperature adjustment thermostat on the control panel of the freezer. It is usually labeled and marked with numbers. 2. Turn the thermostat knob to the desired temperature setting. To achieve a less cold storage temperature, turn the knob to the lower numbers (e.g., 1). For a colder storage temperature, turn the knob to the higher numbers (e.g., 6). 3. If the load indicator inside the appliance is below the "e" symbol, it is recommended to set the thermostat to the lower position (on "e", if present on the thermostat scale) for partial loads. 4. Refer to the climatic class information provided in the manual to determine the appropriate temperature range for your ambient temperature conditions. By following these steps, you can adjust the internal temperature of the Whirlpool AFG 6352 AP freezer to suit your storage needs.

What should I check for before using the Whirlpool AFG 6352 AP freezer?

Before using the Whirlpool AFG 6352 AP freezer, there are several things you should check: 1. Check for any damage: After unpacking the appliance, ensure that it is undamaged and that the lid closes perfectly tight. If you notice any damage, report it to your dealer within 24 hours of delivery. 2. Allow for proper refrigerant circuit efficiency: Wait at least two hours before switching on the appliance to ensure that the refrigerant circuit is fully efficient. 3. Ensure proper installation and electrical connections: The installation of the appliance and electrical connections should be carried out by a qualified electrician, following the manufacturer's instructions and local safety regulations. 4. Clean the inside of the appliance: Before using the freezer, clean the inside to ensure it is free from any dirt or debris. 5. Check the voltage and electrical connections: Ensure that the voltage corresponds to the one indicated on the rating plate located on the rear of the appliance. The electrical connections must be made in accordance with local regulations. By checking these aspects before using the Whirlpool AFG 6352 AP freezer, you can ensure its proper functioning and avoid any potential issues.

How do I properly freeze fresh food in the Whirlpool AFG 6352 AP freezer?

To properly freeze fresh food in the Whirlpool AFG 6352 AP freezer, follow these steps: 1. Prepare the fresh food for freezing by wrapping and sealing it in aluminum foil, cling film, air and water-tight plastic bags, or suitable polyethylene containers. 2. Ensure that the fresh food is of prime quality and mature to obtain high-quality frozen food. 3. Cool hot food before placing it in the freezer to prevent temperature fluctuations. 4. Place the fresh food in direct contact with the walls of the freezer, separating it from already frozen food. 5. For optimal and fast freezing, divide the food into small portions. 6. Press the fast freeze button (if provided) or set the thermostat to the coldest temperature at least 24 hours before storing fresh food in the freezer. 7. Keep the lid of the freezer closed for 24 hours to allow the food to freeze properly. By following these steps, you can properly freeze fresh food in the Whirlpool AFG 6352 AP freezer, ensuring the preservation of its quality and taste.

How do I properly position the defrosting water drainage plug during installation?

To properly position the defrosting water drainage plug during installation of the Whirlpool AFG 6352 AP freezer, follow these steps: 1. Unpack the appliance and remove the 4 protection pieces inserted between the lid and the appliance. 2. Ensure that the defrosting water drainage plug is correctly positioned. The plug is located on the inside of the appliance, usually at the bottom. It may vary depending on the model. 3. Remove the internal defrost water drain plug (depending on the model). 4. Remove the external defrost water drain plug (depending on the model) and reposition it as shown in the figure provided in the manual. 5. Place a bowl beneath the drainage channel to collect the residual water. If available, use the divider to separate the water from the food. By following these steps, you will properly position the defrosting water drainage plug during the installation of the Whirlpool AFG 6352 AP freezer.

Why are the LED indicators not turning on when I switch on the appliance?

If the LED indicators are not turning on when you switch on the Whirlpool AFG 6352 AP freezer, you can follow these troubleshooting steps: 1. Check for a power failure. Ensure that the appliance is properly connected to a functioning power source. 2. Verify that the plug is securely inserted into the socket. Make sure it is not loose or damaged. 3. Inspect the electric cable for any signs of damage. If the cable is frayed or broken, it may need to be replaced. 4. If the green LED indicator is off and the appliance is not working, contact the After Sales Service for a replacement. 5. If the compressor runs continuously, check if hot foods have been placed in the appliance or if the lid has been left open for an extended period. Ensure that the thermostat setting is correct and that the fast freeze function (if available) has not been accidentally activated. 6. If there is excessive ice on the upper edge of the appliance, ensure that the defrost water drainage plugs are correctly positioned and that the appliance lid is properly closed. Check if the lid seal is damaged or deformed. If the issue persists after following these steps, it is recommended to contact the Whirlpool customer support for further assistance.

How do I adjust the internal temperature of the Whirlpool AFG 6352 AP freezer using the thermostat knob?

To adjust the internal temperature of the Whirlpool AFG 6352 AP freezer using the thermostat knob, follow these steps: 1. Locate the temperature adjustment thermostat on the control panel. It is usually labeled and represented by a numbered scale. 2. Turn the thermostat knob to the desired temperature setting. To achieve a less cold storage temperature, turn the knob towards the lower numbers (e.g., 1). For a colder storage temperature, turn the knob towards the higher numbers (e.g., 6). 3. If the load indicator inside the appliance is below the "e" symbol, it is recommended to set the thermostat to the lower position (on "e", if present on the thermostat scale) for partial loads. 4. Refer to the climatic class information provided in the manual to determine the appropriate temperature range for your ambient temperature conditions. By following these steps, you can adjust the internal temperature of the Whirlpool AFG 6352 AP freezer using the thermostat knob.

What should I check for if there is damage to the appliance before using it?

Before using the Whirlpool AFG 6352 AP freezer, you should check for the following damage: 1. Electrical safety: Ensure that the appliance is connected to an approved earth connection to guarantee electrical safety. 2. Self-troubleshooting: Attempt to solve any problems yourself before contacting After-Sales Service. Switch the appliance on again to see if the issue is resolved. If not, disconnect the appliance from the power supply for about an hour before switching it on again. 3. Contact After-Sales Service: If the problem persists, contact After-Sales Service and provide them with the nature of the fault, the model, the service number (found on the rating plate at the rear of the appliance), your full address, and your telephone number. Additionally, the manual suggests general maintenance steps such as cleaning the appliance with warm water and mild detergent, cleaning the side motor cooling grille, and removing dust from the condenser on the rear of the appliance. It is important to unplug the appliance before carrying out any maintenance. By following these steps, you can ensure that the Whirlpool AFG 6352 AP freezer is free from damage and ready for use.

How should I classify and package frozen food for optimal storage in the Whirlpool AFG 6352 AP freezer?

To classify and package frozen food for optimal storage in the Whirlpool AFG 6352 AP freezer, follow these steps: 1. Preparation of fresh food for freezing: - Wrap and seal fresh food in aluminum foil, cling film, air and water-tight plastic bags, or polyethylene containers with lids suitable for freezing. - Ensure that the food is fresh, mature, and of prime quality to obtain high-quality frozen food. - Freeze fresh vegetables and fruits as soon as possible after picking to maintain their nutritional value, consistency, color, and flavor. - Allow hot food to cool before placing it in the freezer. 2. Freezing fresh food: - Place the foods to be frozen in direct contact with the walls of the appliance. - Avoid placing foods to be frozen in direct contact with already frozen food. - Split foods into small portions for faster freezing and easier use. 3. Classification of frozen foods: - Put the frozen products into the appliance and classify them. - Indicate the storage date on the packs to ensure use within the expiry dates. 4. Advice for storing frozen food: - Ensure that the packaging of frozen food is not damaged. - Transport frozen food purchases in a thermally insulated cool bag. - Place frozen foods immediately in the freezer to minimize temperature variations. - Observe the best-before date and storage information on the package. By following these steps, you can classify and package frozen food for optimal storage in the Whirlpool AFG 6352 AP freezer.

Is the manual of the Whirlpool AFG 6352 AP available in English?

Yes, the manual of the Whirlpool AFG 6352 AP is available in English .

Is your question not listed? Ask your question here

No results