Whirlpool 6TH SENSE InfiniteCare AWO 174S3 manual

Whirlpool 6TH SENSE InfiniteCare AWO 174S3
8.4 · 41
PDF manual
 · 2 pages
English
manualWhirlpool 6TH SENSE InfiniteCare AWO 174S3
Whirlpool is a registered trademark of Whirlpool USA

5019 300 01131

Load the laundry, close the door and turn the programme selec-
tor to the desired programme; the “Start/Pause” indicator
blinks. The temperature and spin speed shown on the display
can be altered by pressing the “Temperature” or “Spin”
button . If you do not use the “Dosing Aid” , add deter-
gent now. The washing machine is designed to save energy;
therefore, if you have selected a programme but do not
start it within about a quarter of an hour, it will switch off auto-
matically.To switch it on again, turn the programme selector to
“Off/O” and then to the desired programme.
When the combination of programme and additional option(s) is
not possible, the indicators switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Colours 15°” button
Saves energy used for water heating while maintaining a
good wash result.
Supports colour maintenance when washing coloured laundry.
Recommendable for lightly soiled laundry without stains.
Make sure that your detergent is suitable for cold wash tem-
peratures (15 or 20 °C).
Not selectable for Cotton 70 - 95 °C.
“Intensive rinse” button
More water is added and rinse cycle is prolonged.
This option is particularly suitable for areas with very soft water
or for washing baby linen, and helps people with allergies.
“Rapid” button
Enables quicker washing by shortening the programme duration.
Recommendable for only lightly soiled laundry.
Not selectable for Cotton 70 - 95 °C.
“Prewash” button
Adds a prewash cycle to the wash programme selected; pro-
longs the programme by about a quarter of an hour.
Recommended for heavily soiled laundry (e.g. with sand or
granular dirt).
Do not use liquid detergent for the main wash when activat-
ing the “Prewash” option.
“Soil level” button
Adapts the programme duration to the soil level of your
laundry. Also influences the detergent quantity recommen-
dation when using the “Dosing Aid” button.
= lightly soiled - = normally soiled - = heavily soiled
Not all soil levels are selectable for each programme.
“Spin” button (incl. “Rinse Hold” )
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If you select spin speed “0”, the final spinning is cancelled
and the water is drained out only. However, intermediate
spin phases remain during the rinse.
If you select “Rinse hold , the laundry remains in the
last rinse water without progressing to the final spin cycle, to
avoid creasing and prevent colours from changing. To acti-
vate the “Rinse hold”, press the “Spin” button repeatedly
until the “Rinse hold” symbol on the display lights up.
- The wash programme stops to “Rinse hold” when the
“Rinse hold” symbol on the display blinks; the “Start/
Pause” indicator also blinks.
- To terminate the “Rinse hold” by spinning the laundry, press
“Start/Pause” - the laundry will be spun with the default spin
speed. You can also select another spin speed with the “Spin”
button before you start the spin cycle with “Start/Pause”.
- To terminate the “Rinse hold” by draining the water without
spinning, press the “Spin” button until spin speed “0” appears
on the display; then press “Start/Pause” to start the draining.
- Do not leave the laundry to soak for too long in the “Rinse
hold” (especially silk!).

CONSUMPTION DATA

Programme
Temp era ture
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
without “Rapid” with “Rapid”
Mixed 40 4.0 46 0.40 1:00
Cotton 95 7.0 75** 2.25 2:40
Cotton 60 7.0 58 1.19 2:20 1:45
Cotton 40 7.0 65 0.75 2:05 1:15
Synthetics 60 3.0 48** 0.94 1:37 1:12
Synthetics 40 3.0 42 0.40 1:20 0:55
Delicates 40 1.5 60 0.65 0:50
Wool/Handwash 40 1.0 45 0.55 0:40
White 40 7.0 65 0.75 2:20
Light colours 40 4.0 50 0.45 1:20
Dark 40 4.0 40 0.53 1:40 1:15
Cotton *
60 7.0 59 0.59 4:00
Cotton *
60 3.5 55 0.55 3:30***
Cotton *
40 3.5 48 0.48 3:30***
AquaEco 40 3.0 19 0.50 1:00
Speed 15 30 3.0 20 0.15 0:15
Jeans 40 4.0 53 0.46 1:30 1:10
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15 °C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water
supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature.
Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options
or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
Troubleshooting Guide” in your Instructions for Use).
** To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.
*** Automatic adaptation of programme duration after detection of wash load.
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle
temperature.

LOAD LAUNDRY, CLOSE DOOR AND SELECT

PROGRAMME

SELECT ANY DESIRED OPTION

With this function you can postpone your programme to com-
plete at a later time: press the button to select in how many hours
the programme shall be finished. Thus, it allows you to have your
laundry ready at a particular time and to profit from more favour-
able energy rates during the night, for example.
The time until the “Cycle end” can be selected in full hour time
segments (1 to 24 h). When you press the button, the shortest
possible time will be displayed; keep on pressing the button
to loop through all the available times. To remove it again,
keep on pressing the button until you see the value “0:00”.
When you have selected the desired time until the “Cycle
end”, press “Start/Pause” - the countdown will begin.
During the countdown, you can still modify the programme
setting (select or deselect options, change spin speed etc.).
If the modifications prolong the programme duration so that
it overruns the originally set time until the “Cycle end”, the
programme will start immediately.
Sometimes the programme may finish before the selected
time until the “Cycle end” has expired (e.g. for small loads).
In this case, the washing machine will tumble the laundry
regularly to keep it fresh, until the selected “Cycle end” time
has expired. During tumbling, the display will show an ani-
mation. The tumbling phase can be stopped at any time
either by pressing any button or by rotating the programme
selector; the animation will stop and the door will unlock in
about 1 minute as indicated on the display.
With the “Dosing Aid” button, you can make your washing machine
indicate you the recommended detergent quantity for your wash
load, depending on the soil level selected and the size of the load.
Helps to save detergent and protect the environment and
also sensitive skin by avoiding detergent overdosing.
Before you use this function, you must adapt the washing
machine to the dosing amounts which are recommended for
the detergents you use. Also check if your region’s water
hardness corresponds with the water hardness level “soft”
of your washing machine - if not adapt it.
Select programme, options and cycle end BEFORE using the
“Dosing Aid” button.
For any details, refer to the separate “Dosing Aid” Instructions for Use.
Before starting and after end of a programme, the lamp lights to
show that the door can be opened. As long as a wash programme is
running, the door remains locked and must on no account be forced
open. In case you have an urgent need to open it during a running
programme, refer to “Reset a running programme before the end”.
The “Eco monitor” gives you a rough feedback about the power
consumption of the programme setting you selected.
As soon as you turn the programme selector to any programme,
the “Eco monitor” is on.
The indicator on the left is to show that the “Eco monitor” is active.
The four indicators next to it show the degree of consumption:
the less power your programme setting is forecasted to consume,
the less indicators will light up. This depends on the programme,
temperature and options selected, and also on the size of the wash
load. For that reason, the forecasted degree of power consump-
tion may adapt when the washing machine detects the wash load.
Open the tap and press the “Start/Pause button .
The indicator next to the “Start/Pause” button lights up.
Activating the child lock prevents children from starting a wash cy-
cle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme se-
lector is in the “Off/O” position. To activate the child lock:
Turn the programme selector to a programme position,
or run a programme as usual.
Press and hold the 2 buttons marked with the key symbol
simultaneously for a few seconds. A key-like symbol
will shortly appear on the display to indicate that the child
lock is active.
Any time you try to change a programme setting with active
child lock, the display will briefly show the key-like symbol.
The programme setting cannot be changed anymore. The only
change possible is to switch the washer off by turning the pro-
gramme selector to the “Off/O” position. To deactivate the
child lock:
Press and hold again the 2 buttons marked with the key sym-
bol simultaneously for a few seconds.
If one of the failure indicators blinks, consult the “Troubleshoot-
ing Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
“Service”: failure or malfunction of an electrical component.
“Clean pump”: waste water is not pumped out.
Spin speed on display blinks: unbalance during spinning.
The “Door open” indicator lights up, and the display shows
“End”. After about a quarter of an hour, the washing machine will
switch off completely to save energy.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time. If the symbol
lights up and the display shows “Fod”, too much foam interrupt-
ed the wash process; refer to the “Troubleshooting Guide” in
your Instructions for Use.
1. Press the “Start/Pause” button to pause the pro-
gramme. The indicator blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the “Start/Pause” button again. The new pro-
gramme continues at the same position where the previous
programme was interrupted. Do not add detergent for this
programme.
The “Reset/Drain” button cancels a programme before the end.
Press and hold the
“Reset/Drain button for a few sec-
onds; an animation appears on the display. The water is
drained; it may last some time until you can open the door.

SET CYCLE END

DETERGENT DOSING RECOMMENDATION

“DOOR OPEN” INDICATOR

ECO MONITOR

PROGRAMME START

less more

CHILD LOCK

FAILURE INDICATORS

PROGRAMME END

DETERGENT OVERDOSAGE INDICATOR

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME

- the sensor technology adapts drum movement, water, energy and programme duration to your wash load.
Power consumption: in off-mode 0.16 W / in left-on mode 0.16 W.

View the manual for the Whirlpool 6TH SENSE InfiniteCare AWO 174S3 here, for free. This manual comes under the category washing machines and has been rated by 41 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Whirlpool 6TH SENSE InfiniteCare AWO 174S3 or do you need help? Ask your question here

Need help?

Do you have a question about the Whirlpool and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 19
B
Blaga Violeta December 30, 2023

Hello. Whirlpool 6TH SENSE InfiniteCare AWO 174S3 washing machine, 7 kg, 1000 rpm, does not wash well, most of them come out with stains or not washed well. What could it be? Can you help me with advice? I have used both powder and liquid detergent. Thank you.

Hello. Whirlpool 6TH SENSE InfiniteCare AWO 174S3 washing machine, 7 kg, 1000 rpm, does not wash well, most of them come out ...
zoom-in
View photo
This message has been automatically translated
G
Grigoraș Ana mariaJune 27, 2023

Hello, the screen with the pause button is blinking and I cannot stop the Whirlpool 6th Sense washing machine.

Hello, the screen with the pause button is blinking and I cannot stop the Whirlpool 6th Sense washing machine.
zoom-in
View photo
This message has been automatically translated
N
Neacșu Cătălina August 22, 2022

Hello, the Whirlpool 6TH SENSE InfiniteCare AWO 174S3 washing machine is showing error code FO5. It is not draining the water, I have checked the filter and there is nothing in it.

Hello, the Whirlpool 6TH SENSE InfiniteCare AWO 174S3 washing machine is showing error code FO5. It is not draining the water...
zoom-in
View photo
This message has been automatically translated
P
Popesteanu Emi LucaAugust 16, 2022

I purchased this dishwasher, but for some time now the dishes are not clear anymore, and now it does not wash them anymore. Why? Thank you very much!

I purchased this dishwasher, but for some time now the dishes are not clear anymore, and now it does not wash them anymore. W...
zoom-in
View photo
This message has been automatically translated
L
LEJEUNE December 11, 2020

Why does the closed door indicator not turn off automatically when the door is closed and consequently prevents the program from starting?

This message has been automatically translated
A
Al RAKHAMiJuly 28, 2020

My washing machine (Whirlpool 6th Sense model) has a LED called "Cleaning Filter" that lights up in red before the rinse and spin cycle is done. So water remains in the washing machine. How can I solve this problem?

This message has been automatically translated
R
RayNovember 20, 2023

is it normal when you used deep cleaning for 2hrs and 14mins then the hot water with bubbles flowing into the side of washing machine? Like overflowing or leak something?

I
Isabel Godinho July 10, 2023

The machine stoped in the middle of the cicle and as the code f13 wich I don't find in the manual

The machine stoped in the middle of the cicle and as the code f13 wich I don't find in the manual
zoom-in
View photo
1 comment
R
RayNovember 20, 2023

is it normal when you used deep cleaning for 2hrs and 14mins then the hot water with bubbles flowing into the side of washing machine? Like overflowing or leak something?

The Whirlpool 6TH SENSE InfiniteCare AWO 174S3 is a washing machine designed for home use. It features a variety of washing cycles and options, including several temperature settings and spin speeds. With a capacity of 7kg, it's suitable for washing moderate-sized loads of laundry. The machine's 6TH SENSE technology allows it to automatically adjust water and energy usage based on the weight of the laundry. This helps to save on resources while still providing effective cleaning. It also has a function called InfiniteCare, which uses a combination of eco-friendly detergents, perfume capsules, and steam treatments to keep clothes looking and feeling new for longer. The AWO 174S3 has an A+++ energy rating, indicating that it's highly efficient and environmentally friendly. It also has a noise level of 53 dB during the spin cycle, which is relatively quiet for a washing machine. The machine's design is sleek and modern, with an easy-to-use control panel and a clear LED display. The drum is made of high-quality stainless steel to ensure durability over time. In addition, the machine has safety features such as a child lock and overflow protection. Overall, the Whirlpool 6TH SENSE InfiniteCare AWO 174S3 is a reliable and efficient washing machine that offers a range of features and options for home use.

General
BrandWhirlpool
Model6TH SENSE InfiniteCare AWO 174S3
Productwashing machine
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Whirlpool 6TH SENSE InfiniteCare AWO 174S3 below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

Why is my washing machine not starting?

Make sure the power cord is securely plugged into a functioning electrical outlet. Also, check if the door is properly closed as the machine won't start if the door is open or not closed tightly.

How can I select the appropriate wash cycle for my clothes?

Use the control panel to navigate through the different wash cycles. Look for labels, symbols, or descriptions that indicate the type of fabric or level of dirtiness. Select the cycle that best matches your needs.

What should I do if the machine stops mid-cycle?

Check if the water supply is interrupted or if the water pressure is too low. It might also be due to an unbalanced load causing the machine to stop for safety reasons. Adjust the load, distribute the clothes evenly, and restart the cycle.

How can I adjust the water temperature for a wash cycle?

Use the temperature control options provided on the control panel. You can typically choose from options such as hot, warm, or cold water. Select the desired temperature based on the fabric care instructions and personal preference.

How can I troubleshoot excessive noise during the wash cycle?

Ensure the machine is properly leveled, as an unbalanced machine can result in excessive noise. Also, check if there are any loose objects, such as coins or buttons, in the drum that may be causing the noise. If the issue persists, contact a professional service technician for further assistance.

Is the manual of the Whirlpool 6TH SENSE InfiniteCare AWO 174S3 available in English?

Yes, the manual of the Whirlpool 6TH SENSE InfiniteCare AWO 174S3 is available in English .

Is your question not listed? Ask your question here

No results