Wamsler KF 108 manual

Wamsler KF 108
7.9 · 3
PDF manual
 · 70 pages
English
manualWamsler KF 108
4
15. Im Heizbetrieb können alle Oberflächen und besonders die Sichtscheiben sowie die
Griffe und Bedieneinrichtungen sehr heiß werden. Machen sie Kinder und Jugendli-
che, Ältere Menschen und Tiere auf diese Gefahren aufmerksam, und halten sie sie
während des Heizbetriebes von der Feuerstätte fern. Verwenden Sie zur Bedienung
den beigelegten Schutzhandschuh oder das Hilfswerkzeug. Kinder und Jugendliche
unter 16 Jahren dürfen den Ofen ohne Aufsicht Erziehungsberechtigter nicht bedie-
nen.
16. Es ist darauf zu achten, dass der Aschekasten immer bis Anschlag eingeschoben ist
und besonders darauf zu achten, dass keine heiße Asche entsorgt wird (Brandgefahr).
17. In der Übergangszeit kann es zu Störungen des Schornsteinzuges kommen, so dass
die Abgase nicht vollständig abgezogen werden. Die Feuerstätte ist dann mit einer ge-
ringen Brennstoffmenge, am besten mit Holzspäne/-Wolle zu befüllen und unter Kon-
trolle in Betrieb zu nehmen, um den Schornsteinzug zu stabilisieren. Der Rost sollte
sauber sein.
18. Nach jeder Heizperiode ist es angebracht, die Geräte durch einen Fachmann kontrol-
lieren zu lassen. Ebenfalls sollte eine gründliche Reinigung der Abgaswege und der
Abgasrohre erfolgen.
19. Wenn Ausbesserungen oder Erneuerungen vorgenommen werden müssen, wenden
sie sich bitte rechzeitig unter Angabe der genauen Art.Nr. und Fert.Nr. an Ihren Fach-
händler. Es sind nur Original Wamsler - Ersatzteile zu verwenden.
20. Arbeiten, wie insbesondere Installation, Montage, Erstinbetriebnahme und Servicear-
beiten sowie Reparaturen, dürfen nur durch einen ausgebildeten Fachbetrieb (Hei-
zungs- oder Luftheizungsbau) durchgeführt werden. Bei unsachgemäßen Eingriffen
erlöschen Gewährleistung und Garantie.
21. Da der Festbrennstoff-Ofen/Herd die zur Verbrennung benötigte Luft dem Aufstel-
lungsraum entnimmt, ist dafür zu sorgen, dass über die Undichtheiten der Fenster
oder Außentüren stets genügend Luft nachströmt. Man kann davon ausgehen, dass
dieser durch ein Raumvolumen von mind. 4m³ je kW Nennwärmeleistung gewährleis-
tet ist. Ist das Volumen geringer, kann über Lüftungsöffnungen ein Verbrennungsluft-
verbund mit anderen Räumen hergestellt werden (min. 150cm²).
22. Es ist darauf zu achten, dass die Abstände zu brennbaren Bauteilen und Materialien -
seitlich, vorne und hinten- eingehalten werden. Diese Abstände entnehmen Sie der
Bedienungsanleitung oder dem Typenschild.
23. Die Feuerstätte darf nicht verändert werden, ansonsten verlieren Sie die Zulassung.
24. Der Anschluss an einem Schornstein, dessen wirksame Höhe unter 4m, bei Mehr-
fachbelegung 5m liegt, ist unzulässig. An dem zum Anschluss des Ofens vorgesehe-
nen Schornstein dürfen höchstens zwei bis drei weitere Feuerstätten angeschlossen
sein.
25. Bei einem Schornsteinbrand verschließen Sie sofort alle Öffnungen am Gerät und
verständigen sie die Feuerwehr. Versuchen sie auf keinen Fall selbst zu löschen. Da-
nach unbedingt den Schornstein vom Fachmann überprüfen lassen.
26. Festbrennstoffe erzeugen naturgemäß Ruß, ein Verschmutzen der Sichtscheibe ist
dadurch niemals völlig ausgeschlossen und stellt keinen Mangel dar.
27. Speck- und Sandstein ist ein Naturstein, daher sind Farbabweichungen und Farbän-
derungen normal und kein Grund zur Reklamation.

Manual

View the manual for the Wamsler KF 108 here, for free. This manual comes under the category heaters and has been rated by 3 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Wamsler KF 108 or do you need help? Ask your question here

Need help?

Do you have a question about the Wamsler and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Wamsler KF 108 specifications

Below you will find the product specifications and the manual specifications of the Wamsler KF 108.

General
BrandWamsler
ModelKF 108 | 1238694386
Productheater
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Wamsler KF 108 below.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

How can I troubleshoot if the Wamsler KF 108 heater is not heating up properly?

To troubleshoot if the Wamsler KF 108 heater is not heating up properly, you can follow these steps: 1. Check the power supply: Ensure that the heater is properly connected to a power source and that the power supply is functioning correctly. Check if the power cord is securely plugged in and if there are any issues with the electrical outlet. 2. Verify the thermostat settings: Make sure that the thermostat is set to the desired temperature and that it is functioning correctly. Adjust the thermostat settings and see if the heater starts heating up. 3. Inspect the heating elements: Check if the heating elements are clean and free from any debris or blockages. If there is any buildup or obstruction, carefully clean the heating elements following the manufacturer's instructions. 4. Check the fuel supply (if applicable): If the Wamsler KF 108 heater uses a fuel source such as gas or wood, ensure that there is an adequate supply of fuel. Check if the fuel tank is full or if there are any issues with the fuel line. 5. Contact customer support: If the heater still does not heat up properly after following these steps, it is recommended to contact Wamsler customer support for further assistance. They will be able to provide specific troubleshooting guidance based on the model and any potential issues with the heater. Please note that these troubleshooting steps are general guidelines and may vary depending on the specific model and configuration of the Wamsler KF 108 heater.

What should I do if the Wamsler KF 108 heater is emitting strange odors during operation?

If the Wamsler KF 108 heater is emitting strange odors during operation, you can take the following steps to address the issue: 1. Cure the applied preventive lacquer: The strange odors may be caused by the curing process of the applied lacquer. Operate the fireplace on a low heating level according to the instructions manual for a few hours. Then, heat up the fireplace to its maximal performance for a few hours. 2. Check for steaming oil remains: If there are any steaming oil remains, it can contribute to the strange odors. Follow the instructions manual and operate the fireplace on a low heating level for a few hours to allow any remaining oil to evaporate. 3. Ensure proper ventilation: Make sure the room is well-ventilated during operation. Open windows or provide an external air intake to ensure sufficient fresh air circulation. 4. Use well-dried wood: If you are using wood as a fuel source, ensure that it is well-dried. Wet wood can produce unpleasant odors during combustion. Only use well-dried wood for optimal performance and to minimize odors. 5. Contact customer support: If the strange odors persist or if you have any concerns, it is recommended to contact Wamsler customer support for further assistance. They can provide specific troubleshooting guidance based on your situation. Please note that these steps are general guidelines and may vary depending on the specific model and configuration of the Wamsler KF 108 heater.

How can I troubleshoot if the Wamsler KF 108 heater is not igniting?

To troubleshoot if the Wamsler KF 108 heater is not igniting, you can follow these steps: 1. Check the fuel supply: Ensure that there is an adequate supply of fuel for the heater. If using wood, make sure it is dry and properly sized. If using other fuel types, ensure they are compatible with the heater and properly installed. 2. Verify the ignition source: Check if the ignition source, such as a coal lighter or wood shavings, is properly placed on the grate. Ensure that the ignition source is dry and easily ignitable. 3. Adjust the air intake: Check the primary air intake settings according to the instructions manual. Adjust the primary air intake to the recommended position for ignition. This allows for proper airflow and combustion. 4. Open the door slowly: When opening the door to add fuel or ignite the heater, do it slowly to prevent smoke from escaping. Ensure that there is a bed of hot embers before adding more fuel. 5. Ensure proper ventilation: Make sure the room is well-ventilated during the ignition process. Open windows or provide an external air intake to ensure sufficient fresh air circulation. If the Wamsler KF 108 heater still does not ignite after following these steps, it is recommended to contact Wamsler customer support for further assistance. They can provide specific troubleshooting guidance based on your situation.

What should I do if the Wamsler KF 108 heater is producing excessive smoke?

To troubleshoot if the Wamsler KF 108 heater is producing excessive smoke, you can take the following steps: 1. Check the fuel quality: Ensure that you are using well-dried wood or appropriate fuel for the heater. Wet or low-quality fuel can result in excessive smoke production. Only use properly seasoned and dry wood. 2. Clean the chimney: Regularly clean the chimney to remove any buildup of soot or debris. A dirty chimney can obstruct the airflow and cause smoke to back up into the room. Follow the instructions manual for proper chimney cleaning procedures. 3. Verify the air intake: Check the air intake settings according to the instructions manual. Ensure that the air intake is properly adjusted to allow for sufficient oxygen supply for combustion. Insufficient air supply can lead to incomplete combustion and increased smoke production. 4. Monitor the draft: Ensure that the chimney draft is adequate. A weak draft can cause smoke to linger in the fireplace and escape into the room. Consult an expert to assess and improve the chimney draft if necessary. 5. Contact customer support: If the excessive smoke issue persists or if you have any concerns, it is recommended to contact Wamsler customer support for further assistance. They can provide specific troubleshooting guidance based on your situation. Please note that these steps are general guidelines and may vary depending on the specific model and configuration of the Wamsler KF 108 heater.

How can I troubleshoot if the Wamsler KF 108 heater is not maintaining a consistent temperature?

To troubleshoot if the Wamsler KF 108 heater is not maintaining a consistent temperature, you can follow these steps: 1. Check for odor formation: If there is an odor during operation, it may be due to the curing process of the applied preventive lacquer or steaming oil remains. Operate the heater on a low heating level for a few hours, then heat it up to its maximum performance for a few hours. 2. Ensure sufficient heating performance: If the heater is not providing enough heat, check if the selected heating performance is appropriate for the room. Have an expert examine the heating requirement of the room and ensure that the chimney draft is sufficient. 3. Verify chimney tightness: Check the tightness of the chimney and ensure that all smoke tube joints are well sealed and fireproof-isolated. Replace any worn-out sealing components if necessary. 4. Inspect door glass sealing: Check the sealing of the door glass and ensure that the door is properly closed. If needed, renew the tightening flap. 5. Use well-dried wood: Ensure that only well-dried wood is used as fuel. Wet wood can affect the combustion process and lead to temperature inconsistencies. Please note that these steps are general guidelines and may vary depending on the specific model and configuration of the Wamsler KF 108 heater.

How can I ensure that the Wamsler KF 108 heater is in compliance with the European Directive 89/106/EC: Construction Products Directive?

To ensure that the Wamsler KF 108 heater is in compliance with the European Directive 89/106/EC: Construction Products Directive, you can follow these steps: 1. Check the EC Declaration of Conformity: Look for the EC Declaration of Conformity in the product documentation supplied with the Wamsler KF 108 heater. This document should be provided by the manufacturer and contains important information regarding compliance with the directive. 2. Verify the Manufacturer's Information: Ensure that the manufacturer mentioned in the EC Declaration of Conformity is Wamsler Haus- und Küchentechnik GmbH. This information confirms that the product is from the authorized manufacturer. 3. Confirm the Product Description and Model Number: Check that the product description mentioned in the EC Declaration of Conformity matches the Wamsler KF 108 heater. Additionally, verify that the model number specified is TYP 108 70 / 71. 4. Look for Test Reports: The EC Declaration of Conformity should reference test reports conducted by a state-accredited test center. These reports, such as No. R-20463 3 from TÜV SÜD Kermi, provide evidence of compliance with the Construction Products Directive. 5. Adhere to Safety Notices: The EC Declaration of Conformity mentions safety notices that must be followed. Make sure to read and adhere to these notices to ensure safe usage of the Wamsler KF 108 heater. Please note that these steps are based on the information provided in the manual for the Wamsler KF 108 heater and are intended to guide you in ensuring compliance with the European Directive 89/106/EC: Construction Products Directive.

What should I do if I cannot find the test reports mentioned in the EC Declaration of Conformity for the Wamsler KF 108 heater?

If you cannot find the test reports mentioned in the EC Declaration of Conformity for the Wamsler KF 108 heater, you can take the following steps: 1. Contact the Manufacturer: Reach out to Wamsler Haus- und Küchentechnik GmbH, the manufacturer of the Wamsler KF 108 heater. You can find their contact information in the product documentation or on their official website. Inquire about the availability of the test reports and request a copy if they are not included in the documentation. 2. Check the Manufacturer's Website: Visit the official website of Wamsler Haus- und Küchentechnik GmbH. Look for a dedicated section or page related to the Wamsler KF 108 heater. The website may provide additional information, including access to the test reports or a contact form to request them. 3. Consult Customer Support: Contact the customer support team of Wamsler Haus- und Küchentechnik GmbH. They can assist you in obtaining the test reports or guide you on the next steps to take. Provide them with the necessary details, such as the product model (Wamsler KF 108) and any relevant information from the EC Declaration of Conformity. 4. Seek Authorized Service Centers: Reach out to authorized service centers or dealerships that specialize in Wamsler products. They may have access to the test reports or be able to assist you in obtaining them. Remember, it is important to have the test reports to ensure compliance with the applicable regulations and standards. Taking these steps will help you obtain the necessary documentation for the Wamsler KF 108 heater.

How can I access the EG Konformitätserklärung (EG Declaration of Conformity) for the Wamsler KF 108 heater?

To access the EG Konformitätserklärung (EG Declaration of Conformity) for the Wamsler KF 108 heater, you can follow these steps: 1. Look for the Manufacturer's Information: Check the product documentation or the official website of Wamsler Haus- und Küchentechnik GmbH, the manufacturer of the Wamsler KF 108 heater. They should provide access to the EG Konformitätserklärung. 2. Verify the Product Description and Model Number: Ensure that the product description mentioned in the EG Konformitätserklärung matches the Wamsler KF 108 heater. Additionally, confirm that the model number specified is TYP 108 70 / 71. 3. Check the EC Declaration of Conformity: The EG Konformitätserklärung may be included as part of the EC Declaration of Conformity. Look for this document in the product documentation. It should contain information about compliance with the European Directive 89/106/EC: Construction Products Directive. 4. Contact Customer Support: If you cannot find the EG Konformitätserklärung through the above steps, reach out to the customer support team of Wamsler Haus- und Küchentechnik GmbH. They can provide you with the necessary information or guide you on how to access the EG Konformitätserklärung. Please note that these steps are based on the information provided in the manual for the Wamsler KF 108 heater and are intended to guide you in accessing the EG Konformitätserklärung.

What steps should I take if I encounter any safety notices mentioned in the EC Declaration of Conformity for the Wamsler KF 108 heater?

If you encounter any safety notices mentioned in the EC Declaration of Conformity for the Wamsler KF 108 heater, it is important to take the following steps: 1. Read the Safety Notices: Carefully read and understand the safety notices mentioned in the EC Declaration of Conformity. Pay close attention to any specific warnings, precautions, or instructions provided. 2. Follow the Instructions: Follow the instructions provided in the safety notices to ensure safe usage of the Wamsler KF 108 heater. This may include guidelines on installation, operation, maintenance, and any necessary precautions to prevent accidents or hazards. 3. Seek Professional Assistance: If you are unsure about any of the safety notices or if you need further clarification, it is recommended to seek professional assistance. Contact the manufacturer, Wamsler Haus- und Küchentechnik GmbH, or a qualified technician who is familiar with the Wamsler KF 108 heater. 4. Take Prompt Action: If the safety notices indicate any immediate actions or precautions to be taken, ensure that you promptly follow them. This may involve stopping the use of the heater, contacting the manufacturer, or seeking professional help. Remember, safety notices are provided to ensure the safe and proper use of the Wamsler KF 108 heater. It is crucial to adhere to these notices to minimize any potential risks or hazards.

How can I obtain the necessary information about the manufacturer, product description, and model number for the Wamsler KF 108 heater mentioned in the EC Declaration of Conformity?

To obtain the necessary information about the manufacturer, product description, and model number for the Wamsler KF 108 heater mentioned in the EC Declaration of Conformity, you can follow these steps: 1. Check the Product Documentation: Refer to the product documentation provided with the Wamsler KF 108 heater. Look for any labels, stickers, or tags on the product itself that contain information about the manufacturer, product description, and model number. 2. Examine the Packaging: If you still have the original packaging of the Wamsler KF 108 heater, inspect it for any labels or markings that provide details about the manufacturer, product description, and model number. 3. Visit the Manufacturer's Website: Go to the official website of Wamsler Haus- und Küchentechnik GmbH. Look for a dedicated section or page related to the Wamsler KF 108 heater. The website may provide detailed information about the manufacturer, product description, and model number. 4. Contact Customer Support: If you are unable to find the necessary information through the above steps, reach out to the customer support team of Wamsler Haus- und Küchentechnik GmbH. They can assist you in obtaining the required details or guide you on the next steps to take. By following these steps, you can obtain the necessary information about the manufacturer, product description, and model number for the Wamsler KF 108 heater as mentioned in the EC Declaration of Conformity.

Is the manual of the Wamsler KF 108 available in English?

Yes, the manual of the Wamsler KF 108 is available in English .

Is your question not listed? Ask your question here

No results