Vango Anteus 600SE manual

Vango Anteus 600SE
  • Number of pages: 4
  • Filetype: PDF



Assemble poles and lay them on the ground
Open out flysheet and position in required direction
Locate pole sleeves on the flysheet and insert poles. The poles are colour coded to the pole sleeves.
Locate one end of each pole at one side of the tent into the metal pin system attached to the groundsheet
Make sure poles locate into correct pin system, all poles follow corresponding flysheet seams to pin system
Push poles into an arch from opposite ends and locate pole ends into corresponding metal pin
Tighten all the tensions straps at the base of the poles.
Securely peg out the rear corners of the tent
Ensure the tent is in a straight line
Peg out the remaining poles and pegging points using pin pegs at the base of poles
Attach all flysheet pole clips onto poles
Peg out ALL guy lines using pin-pegs ensuring that guy line fabric attachment points are evenly tensioned.


To erect the pre-attached canopy, insert the pole into the sleeve, connect to Ring and Pin system, tighten the tension straps and attach

pole clips to pole.

Pull canopy away from tent until roof of canopy is taut
Peg out ALL guy lines using pin-pegs ensuring that guy line fabric attachment points are evenly tensioned.


Suspend the inner by attaching toggles of inner tent through rings on inside of flysheet
Do the rear first and work forward
It is advisable to remove the inner when taking down the tent when wet.


Remove Tension Band System from pockets and attach into the corresponding clips at the apex of the pole
Adjust the straps until they are taut
DO NOT OVERTENSION. Excess tension will alter the shape of the tent
Tension bands are designed to stabilise the tunnel structure of the tent
The bands are not required to be used in calm weather


Locate one end of pole onto the corresponding metal pin (figure 1)
Peg the corners of the tent through the metal rings using pin-pegs (figure 2)
Pegs should be positioned at a 45 degree angle to ensure maximum grip



Stecken Sie die Stangen zusammen und legen Sie sie auf den Boden
Außenzelt auslegen und korrekt ausrichten.
Fixieren Sie die Stangenhüllen am Überdach und setzen Sie die Stangen ein. Die Stangen und Stangenhüllen sind farblich gekennzeichnet.
Befestigen Sie ein Ende jeder Stange auf einer Seite des Zelts in dem an der Bodenplane befestigte Metallstiftsystem.
Achten Sie darauf, dass die Stangen in das korrekte Stift-System eingesteckt werden; alle Stangen verlaufen an den zugehörigen

Außenzeltnähten entlang zum Stift-System.

Schieben Sie die Stangen von den gegenüberliegenden Seiten in eine gewölbte Form und stecken Sie die Stangenenden in die zugehörigen

Metallstifte ein.

Alle Spanngurte unten an den Stangen fest anziehen.
Stecken Sie die hinteren Ecken des Zelts fest aus.
Achten Sie darauf, dass sich das Zelt in einer geraden Linie ausgerichtet befindet.
Übrige Stangen und Verankerungspunkte mithilfe der Stiftheringe unten an den Stangen fixieren.
Befestigen Sie alle Außenzelt-Halterungsklemmen an den Stangen.
Vango Anteus 600SE

Need help?

Number of questions: 0

Do you have a question about the Vango Anteus 600SE or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Vango Anteus 600SE owners to properly answer your question.

View the manual for the Vango Anteus 600SE here, for free. This manual comes under the category Tents and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Vango Anteus 600SE or do you need help? Ask your question here

Vango Anteus 600SE specifications

Brand Vango
Model Anteus 600SE
Product Tent
Language English
Filetype PDF

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Vango Anteus 600SE.

Is your question not listed? Ask your question here