Vaddio RoboSHOT 12E HDBT manual

Vaddio RoboSHOT 12E HDBT
6.8 · 1
PDF manual
 · 140 pages
English
manualVaddio RoboSHOT 12E HDBT

Camera Control and Other Issues

What is it doing? Possible causes Check and correct
The camera does not
respond to the remote, but
the web interface is
available.
The remote and the camera are not
using the same IR channel.
Press the Camera Select 1 button on
the remote. Try the other Camera
Select buttons if necessary.
The remote's batteries are dead. Put new batteries in the remote.
The camera responds to
the remote but not to the
web interface.
The web interface is controlling a
different camera. (Check by
removing power from the camera;
the web interface should become
unavailable.)
Check the camera's IP address. See
Getting the camera's IP address.
More than one device is using this
IP address.
The camera responds to
the remote but the web
interface is not available.
The camera is not using the IP
address you browsed to.
Press the Data Screen button on the
remote to see camera information.
The camera is not connected to the
network.
Connect the network cable.
The camera responds to
the remote but the web
interface is not available.
The camera is not using the IP
address you browsed to.
Press the Data Screen button on the
remote to see camera information.
Camera connected to a Quick-
Connect USB Mini: The Quick-
Connect device is in video mode.
Press the white button on the QMini to
switch from video mode to control
mode. Web control is not available
when the device is in video mode.
The camera loses all its
settings when power is
cycled.
All the DIP switches are in the ON
(down) position.
Set the DIP switches to their proper
positions. Default is all OFF (up). See
DIP Switches: Camera Behavior
Settings for more information.

Status Light

The light in the camera's base indicates its current state.
n Blue: Normal operation (blinks once when the camera receives a command from the remote)
n Red: On-air tally (signal provided by external device via serial connection)
n Blinking red: Video is muted (UC color scheme only)
n Purple: In standby mode or booting
n Yellow: Firmware update in progress
Caution
Do not remove power or reset the camera while the indicator is yellow, showing a firmware update in
progress. Interrupting a firmware update can make the camera unusable.
Note
By default, the camera's status light is active during normal operation; however, it can be configured to
remain off when the camera is powered up. The camera may be sending video even if the indicator light is
off.
117
Complete Manual for RoboSHOT CAT-5 Professional PTZ Camera Systems

Manual

View the manual for the Vaddio RoboSHOT 12E HDBT here, for free. This manual comes under the category video conferencing systems and has been rated by 1 people with an average of a 6.8. This manual is available in the following languages: English. Do you have a question about the Vaddio RoboSHOT 12E HDBT or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Vaddio and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Vaddio RoboSHOT 12E HDBT specifications

Below you will find the product specifications and the manual specifications of the Vaddio RoboSHOT 12E HDBT.

General
BrandVaddio
ModelRoboSHOT 12E HDBT | 999-99600-000W
Productvideo conferencing system
EAN0840077504083
LanguageEnglish
FiletypeUser manual (PDF)
Camera
Megapixel8.57 MP
Sensor typeCMOS
Optical sensor size1/2.5 "
Effective sensor resolution8.51 MP
Optical zoom12 x
Focal length range4.4 - 88.4 mm
Horizontal field of view (wide)70.2 °
Horizontal field of view (tele)4.1 °
Minimum illumination1.6 lx
White balanceATW, Auto, Indoor, Manual, One push, Outdoor
Auto focusing (AF) modesOne Push Trigger
Signal-to-Noise Ratio (SNR)50 dB
Focus adjustmentAuto/Manual
Closest focusing distance0.08 m
Wide Dynamic Range (WDR)Yes
Back Light Compensation (BLC)Yes
Number of camera presets17
Aperture number of steps16
Gain control typeAuto/Manual
Aspect ratio3:2, 4:3, 16:9
PTZ controlYes
Aperture range (F-F)2 - 3.8
Slowest camera shutter speed1 s
Fastest camera shutter speed1/10000 s
Power
Power source typePoE
Operational conditions
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)20 - 80 %
Audio
Noise reductionYes
Network
Network streamingYes
Video
Maximum video resolution1920 x 1080 pixels
Supported video modes720p, 1080i, 1080p
Maximum frame rate60 fps
HD typeFull HD
Video formats supportedH.264
Design
Product colorWhite
Mounting typeStand
Tilt angle range-30 - 90 °
Pan range-160 - 160 °
Web-based managementYes
Tilt speed (min)0.35 °/sec
Tilt speed (max)120 °/sec
Pan speed (min)0.35 °/sec
Pan speed (max)120 °/sec
Ports & interfaces
HDMI ports quantity1
Power over Ethernet plus (PoE+) ports quantity1
RS-232 ports1
Weight & dimensions
Width179.1 mm
Depth171.5 mm
Height176.3 mm
Weight2200 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Vaddio RoboSHOT 12E HDBT below.

What is the weight of the Vaddio RoboSHOT 12E HDBT?

The Vaddio RoboSHOT 12E HDBT has a weight of 2200 g.

What is the height of the Vaddio RoboSHOT 12E HDBT?

The Vaddio RoboSHOT 12E HDBT has a height of 176.3 mm.

What is the width of the Vaddio RoboSHOT 12E HDBT?

The Vaddio RoboSHOT 12E HDBT has a width of 179.1 mm.

What is the depth of the Vaddio RoboSHOT 12E HDBT?

The Vaddio RoboSHOT 12E HDBT has a depth of 171.5 mm.

Is the manual of the Vaddio RoboSHOT 12E HDBT available in English?

Yes, the manual of the Vaddio RoboSHOT 12E HDBT is available in English .

Is your question not listed? Ask your question here

No results