Uniden DXI 8560 manual

Uniden DXI 8560
7.3 · 1
PDF manual
 · 12 pages
English
manualUniden DXI 8560
Sheet 3
Note: For optimum battery life, charge all of your handsets completely before you connect the
telephone cord. The rst time you charge a new battery, allow 15 to 20 hours.

1-4. Connect the Telephone Cord

If you receive high-speed internet service through
your telephone line (referred to as DSL), you
should install a DSL lter between the telephone
base and the wall jack. Standard telephones
often can’t operate correctly without a DSL lter.
Test the connection
12
Make a quick test call, and then press [END] to hang up.
What if the call doesn't go through?
Check to see if your telephone provider uses pulse dialing.
(See section 3-1 on System Options.)
What if there is a lot of static?
Check the sources of interference described in section
1-1 on Choosing the best location: is the base near
any of those?

1-5. Register the Accessory Handsets

1-6. Things to Remember

When you charge the handsets, the Caller ID summary screen and the
name of the handset appear in the display.
Lots of people put HANDSET #1 in the base, but it doesn’t matter which
handset you put in the base and which one you put in the charging cradle.
Now your phone is ready to use!

1-7. Attach the Belt Clip

To attach the belt clip
Insert the tabs on the side of the belt clip into the holes on either side of the handset.
Press the belt clip down until it clicks into place. (Tug on the clip to make sure it’s secure.)
To remove the belt clip
Gently pull the tabs out of the holes, then slide the belt clip o of the handset.
8
Place one handset in the base and the other in the charging cradle.
What if the charge LED doesn't
light up?
Check AC adapter connection.
Make sure you are not using
an outlet that's controlled by
a wall switch.
Make sure that the
/in use and LEDs
illuminate.
8
Place one handset in the base and the other in the charging cradle.
What if the charge LED doesn't
light up?
Check AC adapter connection.
Make sure you are not using
an outlet that's controlled by
a wall switch.
Make sure that the
/in use and LEDs
illuminate.
9
Connect the telephone cord to the
TEL LINE jack on the rear of the base.
10
Connect the telephone cord
to a telephone wall jack.
To telephone
wall jack
Telephone cord (supplied)
Note: If the telephone cord does not fit into your telephone wall jack, contact your
local phone provider for assistance.
To TEL LINE
9
Connect the telephone cord to the
TEL LINE jack on the rear of the base.
10
Connect the telephone cord
to a telephone wall jack.
To telephone
wall jack
Telephone cord (supplied)
Note: If the telephone cord does not fit into your telephone wall jack, contact your
local phone provider for assistance.
To TEL LINE
Telephone
wall jack
Telephone cord
DSL filter
Telephone
wall jack
Telephone cord
DSL filter
11
Pick up the handset from the base and press [TALK/flash].
You should hear a dial tone, and the display should show TALK.
What if I can't hear a dial tone?
Check the telephone cord connection on the base.
What if the display doesn't show TALK?
Put the handset back in the base for at least five seconds.
Make sure the /in use LED flashes.
Talk 0:01
11
Pick up the handset from the base and press [TALK/flash].
You should hear a dial tone, and the display should show TALK.
What if I can't hear a dial tone?
Check the telephone cord connection on the base.
What if the display doesn't show TALK?
Put the handset back in the base for at least five seconds.
Make sure the /in use LED flashes.
Talk 0:01
13
14
One by one, put each additional handset in the base.
The /in use LED should flash as the base recognizes the handset.
Wait at least five seconds, then pick up the handset and press
[TALK/flash]. Make sure you can get a dial tone on each handset.
What if the /in use LED
doesn't flash?
Pick the handset up and put it back
in the base.
13
14
One by one, put each additional handset in the base.
The /in use LED should flash as the base recognizes the handset.
Wait at least five seconds, then pick up the handset and press
[TALK/flash]. Make sure you can get a dial tone on each handset.
What if the /in use LED
doesn't flash?
Pick the handset up and put it back
in the base.

HS1

New :01

Total:17

HS1

New :01

Total:17

Manual

View the manual for the Uniden DXI 8560 here, for free. This manual comes under the category phones and has been rated by 1 people with an average of a 7.3. This manual is available in the following languages: English. Do you have a question about the Uniden DXI 8560 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Uniden and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Uniden DXI 8560 specifications

Below you will find the product specifications and the manual specifications of the Uniden DXI 8560.

General
BrandUniden
ModelDXI 8560
Productphone
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Uniden DXI 8560 below.

Is the manual of the Uniden DXI 8560 available in English?

Yes, the manual of the Uniden DXI 8560 is available in English .

Is your question not listed? Ask your question here

No results