Uniden DXC 834 manual

Uniden DXC 834
7.3 · 1
PDF manual
 · 28 pages
English
manualUniden DXC 834

Low Battery Indicator

When the Battery Pack
in the Handset is very
low and needs to be
charged, the
TALK/BATT
LOW
LED flashes.
If the
TALK/BATT LOW
LED begins to flash, the phone
is programmed to eliminate its functions to save
power. The table below describes what to do to
return your phone to normal operation.
During a Call In Standby Mode
Only the

T button operates.

None of the buttons will
operate.
The Handset beeps and the
TALK/BATT LOW
LED flashes
once every 3 seconds.
The Handset
TALK/BATT
LOW
LED flashes once
every 3 seconds.
Complete your call as
quickly as possible.
You will not be able to make
a call.
Return the Handset to the
Base Unit for charging.
Return the Handset to the
Base Unit for charging.

Note: Allow 15 to 20 hours without any interruption

for the Handset to fully recharge.

Setting the Pulse/Tone Switch

Be sure the
PULSE/TONE
switch is in
the
TONE
position.

Note: Most phone systems are Tone dialing. Check

with your local phone company if you are not

sure whether your system is Tone or Pulse

dialing.

Adjusting Ringer Controls

To adjust the ringer volume of your Handset, press

G when the phone is not in use.

You can also select one of two different ringer tones
for the Handset.
Press G to select a different ringer tone when the
phone is not in use.

Adjusting Handset Receiver

Volume

Volume settings are Normal and High. When the
Handset is first picked up, the volume will be at the
normal setting. Pressing the
V
will change the
volume to High. This can be accomplished during a
call.

Automatic Digital Code Security

To avoid unauthorized calls on your phone, a Digital
Code feature was added to the DX834 phone. This
Digital Code is shared only between the Handset
and Base Unit. The Code is set

automatically

when
you first use the phone.
To change the Digital Code:
1. Be sure the Handset is on the Base then:
2. Press the
PAGE/FIND
button on the Base Unit.
The Handset begins beeping.
3. When the
beeping stops,
remove the
Handset for 5
seconds, and then
return it to the
Base Unit.

Note: The

Status

LED will blink to

indicate that the

Digital Security

Code is set to one

of the more than

65,000 codes.

If the Base Unit loses power while the Handset is off
the Base, the Digital Code may be erased. When
this happens, the Handset will not function. To
reestablish communication between the Handset
and Base Unit:
1. Restore power to the Base Unit.
2. Place the Handset back on the Base Unit.
3. The
Status
LED will blink to indicate that the
Digital Security Code is set.
14 DX834/DXC834

Manual

View the manual for the Uniden DXC 834 here, for free. This manual comes under the category phones and has been rated by 1 people with an average of a 7.3. This manual is available in the following languages: English. Do you have a question about the Uniden DXC 834 or do you need help? Ask your question here

Need help?

Do you have a question about the Uniden and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Uniden DXC 834 specifications

Below you will find the product specifications and the manual specifications of the Uniden DXC 834.

General
BrandUniden
ModelDXC 834
Productphone
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Uniden DXC 834 below.

Is the manual of the Uniden DXC 834 available in English?

Yes, the manual of the Uniden DXC 834 is available in English .

Is your question not listed? Ask your question here

No results