View the manual for the Tunturi FitCross 150i here, for free. This manual comes under the category crosstrainers and has been rated by 3 people with an average of a 8.3. This manual is available in the following languages: English. Do you have a question about the Tunturi FitCross 150i or do you need help? Ask your question here
| Brand | Tunturi |
| Model | FitCross 150i |
| Product | crosstrainer |
| Language | English |
| Filetype | User manual (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Tunturi FitCross 150i below.
As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.
As a rule of thumb for your maximum heart rate, you can use 220 minus your age.
To reset the safety warnings on the Tunturi FitCross 150i crosstrainer, follow these steps: 1. Make sure the crosstrainer is powered off and unplugged from the power source. 2. Locate the safety warning reset button on the console. It is usually labeled as "Reset" or "Clear". 3. Press and hold the safety warning reset button for about 10 seconds. 4. Release the button when you see the safety warnings on the console disappear or when the console restarts. 5. Plug the crosstrainer back into the power source and turn it on. By following these steps, you should be able to reset the safety warnings on the Tunturi FitCross 150i crosstrainer. If you continue to experience issues or if the safety warnings persist, it is recommended to refer to the troubleshooting section of the manual or contact the dealer for further assistance.
The resistance not working properly during workouts on the Tunturi FitCross 150i crosstrainer can be due to various reasons. Here are some troubleshooting steps to address this issue: 1. Check the power supply: Ensure that the crosstrainer is properly connected to a power source and that the power cable is securely plugged in. If the crosstrainer is battery-operated, make sure the batteries are not depleted and are inserted correctly. 2. Verify the resistance level: Check if the resistance level is set to the desired intensity. Use the console or controls on the crosstrainer to adjust the resistance level. Make sure the resistance setting is not too low or too high for your workout. 3. Clean and lubricate the crosstrainer: Dust or debris accumulation can affect the smooth operation of the resistance mechanism. Clean the crosstrainer regularly using a soft, absorbent cloth. Apply a small amount of silicon lubricant to the moving parts, such as the rails, to ensure smooth movement. 4. Check for any loose or damaged parts: Inspect the crosstrainer for any loose or damaged parts, such as cables, belts, or pulleys. Tighten any loose screws or bolts and replace any damaged components if necessary. 5. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact the Tunturi customer support or the dealer from whom you purchased the crosstrainer for further assistance. Provide them with the model number, serial number, and a detailed description of the problem for better support. By following these troubleshooting steps, you should be able to address the issue of the resistance not working properly during your workouts on the Tunturi FitCross 150i crosstrainer.
If the power supply is not working on the Tunturi FitCross 150i crosstrainer, you can follow these steps to troubleshoot the issue: 1. Check the mains voltage: Ensure that the mains voltage matches the voltage specified on the rating plate of the crosstrainer. Using the wrong voltage can cause power supply problems. 2. Avoid using an extension cable: It is recommended not to use an extension cable with the crosstrainer. Plug it directly into a wall socket to ensure a stable power supply. 3. Inspect the mains cable: Make sure the mains cable is not damaged or defective. If you notice any damage, contact your dealer for assistance. Fully unwind the mains cable and avoid running it underneath the crosstrainer or placing objects on it. 4. Verify the power connection: Ensure that the crosstrainer is properly plugged into the power source. Check if the power cable is securely connected to the crosstrainer and the wall socket. 5. Contact customer support: If the power supply issue persists after following these steps, it is recommended to contact Tunturi customer support or your dealer for further assistance. Provide them with detailed information about the issue for better support. By following these troubleshooting steps, you should be able to address the power supply issue on the Tunturi FitCross 150i crosstrainer.
To calibrate the console on the Tunturi FitCross 150i crosstrainer, follow these steps: 1. Power on the crosstrainer by plugging in the power supply or by pressing any key on the console if it is in sleep mode. 2. Once the console is powered on, you will see all the segments of the LCD display. 3. Use the UP and DOWN buttons to navigate through the menu options on the console. 4. Select the "Settings" or "Setup" option using the MODE button. 5. Within the settings menu, look for the "Calibration" or "Console Calibration" option. 6. Select the calibration option and follow the on-screen instructions to calibrate the console. This may involve entering specific values or performing certain actions as prompted by the console. 7. Once the calibration process is complete, the console should be calibrated and ready for use. If you encounter any difficulties during the calibration process or if the console does not respond as expected, it is recommended to refer to the troubleshooting section of the manual or contact Tunturi customer support for further assistance.
The Bluetooth connection troubleshooting information for the Tunturi FitCross 150i crosstrainer is as follows: 1. Ensure compatibility: The Tunturi FitCross 150i crosstrainer is designed to connect with specific fitness apps via Bluetooth. Make sure you are using a compatible app that is recommended in the manual, such as "Fit Hi Way" or "Kinomap Fitness." 2. Check app permissions: Ensure that the fitness app has the necessary permissions to access Bluetooth on your mobile device. Check the app settings and enable Bluetooth access if required. 3. Restart the crosstrainer and mobile device: Power off the crosstrainer and your mobile device. Wait for a few seconds, then power them back on. This can help refresh the Bluetooth connection. 4. Keep devices in close proximity: Ensure that your mobile device is within close range of the crosstrainer, preferably within a few meters. Bluetooth connections can weaken with distance, so keeping the devices close can improve connectivity. 5. Reset Bluetooth settings: If the connection issue persists, try resetting the Bluetooth settings on both the crosstrainer and your mobile device. Refer to the device settings or the manual for instructions on how to reset Bluetooth settings. If you continue to experience difficulties with the Bluetooth connection, it is recommended to contact Tunturi customer support or the app developer for further assistance.
To ensure your safety while using the Tunturi FitCross 150i crosstrainer, follow these steps: 1. Read the safety warnings and instructions provided in the manual. It is important to understand and follow these guidelines to prevent personal injury or damage to the equipment. Keep the safety warnings and instructions for future reference. 2. The FitCross 150i crosstrainer is designed for domestic use only and is not suitable for commercial use. The maximum recommended usage is limited to 5 hours per day. 3. If you have any physical, sensory, mental, or motorial disabilities, or lack experience and knowledge, consult with a physician or a qualified professional before using the crosstrainer. 4. Before starting your workout, consult a physician to check your health and ensure that you are fit for exercise. 5. If you experience any abnormal symptoms such as nausea, dizziness, or pain during your workout, immediately stop and consult a physician. 6. Always warm up before starting your workout and cool down at the end. Stretching after your workout can help prevent muscular pain and strain. 7. The FitCross 150i crosstrainer is designed for indoor use only. Ensure that you use it in environments with adequate ventilation and ambient temperatures between 10°C to 35°C. 8. Do not use or store the crosstrainer in humid surroundings, and keep the air humidity below 80%. 9. Only use the crosstrainer for its intended purpose as described in the manual. Do not use it for other purposes. 10. Inspect the equipment before each use and do not use it if any part is damaged or defective. Contact your dealer for assistance in such cases. 11. Keep your hands, feet, hair, and clothing away from the moving parts of the crosstrainer to avoid any accidents or injuries. 12. Wear appropriate clothing and shoes while using the crosstrainer. 13. Ensure that only one person uses the equipment at a time, and the maximum weight limit should not exceed 150 kg (330 lbs). By following these safety guidelines, you can enjoy a safe and effective workout on the Tunturi FitCross 150i crosstrainer.
The resistance not working properly on the Tunturi FitCross 150i crosstrainer can be due to several reasons. Here are some troubleshooting steps to resolve the issue: 1. Check the power supply: Ensure that the crosstrainer is properly connected to a power source. Make sure the power cable is securely plugged in and there are no loose connections. 2. Verify the resistance level: Check if the resistance level is set correctly. Use the console or control panel to adjust the resistance level and make sure it is not set too low or too high. 3. Clean the magnetic resistance system: Over time, dust or debris may accumulate on the magnetic resistance system, affecting its performance. Use a soft, dry cloth to clean the magnetic resistance system and remove any dirt or debris. 4. Inspect the cables and connectors: Check the cables and connectors that are responsible for controlling the resistance. Ensure that they are properly connected and not damaged or frayed. If any cables or connectors are damaged, contact the dealer or manufacturer for assistance. 5. Reset the crosstrainer: If the above steps do not resolve the issue, try resetting the crosstrainer. Turn off the power, wait for a few seconds, and then turn it back on. This can help reset any software or hardware issues that may be causing the resistance problem. If the resistance issue persists after following these troubleshooting steps, it is recommended to contact the dealer or manufacturer for further assistance or to schedule a service appointment.
To connect the Tunturi FitCross 150i crosstrainer to a power supply, follow these steps: 1. Locate the power supply input on the crosstrainer. It is usually located at the back or bottom of the machine. 2. Plug the power cable into the power supply input of the crosstrainer. Ensure that the cable is securely inserted and there are no loose connections. 3. Connect the other end of the power cable to a power outlet. Make sure the outlet is easily accessible and has a stable power supply. 4. Once the crosstrainer is connected to the power supply, you should see the console or control panel light up. This indicates that the crosstrainer is receiving power. 5. If the console does not light up, check the power outlet to ensure it is functioning properly. You can try plugging another device into the outlet to test it. 6. If the console still does not light up, check the power cable and connections for any damage or loose connections. If necessary, replace the power cable or contact the dealer or manufacturer for assistance. By following these steps, you can successfully connect the Tunturi FitCross 150i crosstrainer to a power supply and ensure that it is ready for use.
The console may not be connecting to the Bluetooth on the Tunturi FitCross 150i crosstrainer due to the following reasons: 1. Check the Bluetooth settings: Ensure that the Bluetooth function is enabled on the console. Refer to the console's user interface or settings menu to verify if Bluetooth is turned on. 2. Check the device compatibility: Ensure that the device you are trying to connect to the console is compatible with the FitCross 150i crosstrainer. The manual provides information on compatible apps and devices. Make sure you are using the recommended app and device for optimal compatibility. 3. Restart the console and device: Sometimes, restarting both the console and the device can resolve connectivity issues. Turn off the console and the device, wait for a few seconds, and then turn them back on. Attempt to establish the Bluetooth connection again. 4. Ensure proximity and clear interference: Make sure that the console and the device are within close proximity to establish a stable Bluetooth connection. Remove any potential sources of interference, such as other Bluetooth devices or electronic devices, that may disrupt the connection. 5. Update firmware and app: Check for any available firmware updates for the console and ensure that you have the latest version of the app installed on your device. Updating the firmware and app can address any compatibility issues and improve connectivity. If the console still does not connect to the Bluetooth after following these steps, it is recommended to contact the dealer or manufacturer for further assistance or troubleshooting.
To clean and maintain the Tunturi FitCross 150i crosstrainer, follow these steps: 1. Regular cleaning: Wipe down the crosstrainer after each use with a soft, damp cloth to remove sweat and dirt. Pay attention to areas such as the handles, pedals, and console. Avoid using harsh chemicals or abrasive cleaners that may damage the surfaces. 2. Lubrication: Apply a silicone-based lubricant to the rails and joints of the crosstrainer every 3 to 6 months, or as recommended in the manual. This helps ensure smooth and quiet operation. Follow the instructions in the manual for the specific lubrication points and the type of lubricant to use. 3. Check for loose parts: Regularly inspect the crosstrainer for any loose or damaged parts. Tighten any loose screws or bolts using the appropriate tools. If you notice any damaged parts, contact the dealer or manufacturer for replacement or repair. 4. Handlebar and pedal adjustment: Check the handlebars and pedals for proper alignment and adjustment. Ensure that they are securely fastened and in the correct position for your comfort and safety. Refer to the manual for instructions on how to adjust the handlebars and pedals if needed. 5. Transport and storage: If you need to move or store the crosstrainer, follow the guidelines provided in the manual. Use caution and avoid dragging the crosstrainer to prevent damage to the components. By following these steps, you can effectively clean and maintain the Tunturi FitCross 150i crosstrainer, ensuring its longevity and optimal performance.
Yes, the manual of the Tunturi FitCross 150i is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Tunturi and is the answer not in the manual?
Question and answer
Number of questions: 0