View the manual for the Toyotomi LC-32F here, for free. This manual comes under the category heaters and has been rated by 1 people with an average of a 8.3. This manual is available in the following languages: English. Do you have a question about the Toyotomi LC-32F or do you need help? Ask your question here
Below you will find the product specifications and the manual specifications of the Toyotomi LC-32F.
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Toyotomi LC-32F below.
Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.
To troubleshoot if the temperature regulation of the Toyotomi LC-32F heater is not working properly, you can follow these steps: 1. Check the adjustment keys: Use the adjustment keys (▼hour / ▲min.) to adjust the temperature. Make sure the keys are functioning correctly and responding to your input. 2. Adjust the temperature: Use the key on the right (▲min.) to set the temperature to a higher setting and the key on the left (▼hour) to lower the temperature. Ensure that the temperature setting is appropriate for your comfort. 3. Monitor the room temperature: The heater will burn at either high or medium burning mode until the room temperature reaches or slightly exceeds the set temperature. If the heater is not maintaining the desired temperature, check if the room temperature is accurately measured behind the heater. 4. Reset the temperature setting: If you have changed the set temperature, ensure that the new setting is appropriate. If needed, reset the temperature to the standard setting of 20°C. If these troubleshooting steps do not resolve the issue with temperature regulation, it is recommended to consult your dealer for further assistance.
If the Toyotomi LC-32F heater does not turn off when you use the power switch, you can try the following steps to troubleshoot the issue: 1. Press the power switch to the "OFF" position: While the heater is burning, press the power switch to the "OFF" position. This should extinguish the heater, and the ON/OFF Lamp on the indicator panel will go out. 2. Allow the heater to cool down: After turning off the heater, the circulation fan motor will continue to operate for approximately 90 seconds to assist in cooling down the heater. It is important to let the heater cool down before taking any further steps. 3. Avoid disconnecting the heater plug: Never turn off the heater by disconnecting the heater plug from the main electrical supply. This can cause damage to the heater and is not recommended. 4. Wait for automatic deactivation: The Toyotomi LC-32F heater is equipped with a safety system that automatically switches off the heater after 65 hours of continuous operation. If the heater does not turn off immediately, wait for this automatic deactivation to occur. If the issue persists and the heater still does not turn off, it is recommended to consult your dealer for further assistance.
If the automatic deactivation feature of the Toyotomi LC-32F heater is not working after two hours of continuous burning, you can try the following steps to troubleshoot the issue: 1. Check the autoclean procedure: When the heater has been burning continuously for two hours at its highest setting, the burner should automatically start an autoclean procedure. During this procedure, the heater will burn at its lowest setting while the burner autocleans. Ensure that the autocleaning code is running and that the burner is being cleaned. 2. Verify the duration of the autoclean procedure: The autoclean procedure should take approximately 5 minutes. Monitor the display to see if the autocleaning code runs back to the highest setting after the burner is clean. If the autoclean procedure takes longer than expected or does not occur at all, there may be an issue with the automatic deactivation feature. 3. Restart the heater: If the automatic deactivation feature is not working, try turning off the heater by pressing the power switch to the "OFF" position. Wait for at least ten minutes before restarting the heater. This can help reset any potential issues with the automatic deactivation feature. If these troubleshooting steps do not resolve the issue, it is recommended to consult your dealer for further assistance.
If the automatic cleaning mode of the Toyotomi LC-32F heater is not functioning as described in the manual, you can try the following steps to address the issue: 1. Turn off the heater: While the heater is burning, press the power switch to the "OFF" position. This will extinguish the heater, and the ON/OFF Lamp on the indicator panel will go out. 2. Allow the heater to cool down: After turning off the heater, wait for it to cool down completely before proceeding with any maintenance or cleaning. This is important for safety reasons. 3. Perform routine maintenance: Regular maintenance is crucial for the proper functioning of the heater. Clean the air filter on a weekly basis using a vacuum cleaner to prevent clogging. Also, clean the fan cover at the back of the heater to remove any dust. 4. Check the fuel acceptance fitting: Ensure that the fuel acceptance fitting is clean and free from dirt or dust. Clean it if necessary, especially when refueling. 5. Check for fuel leaks: Regularly inspect the sub tank and removable fuel tank for any signs of fuel leakage. Wipe off any spilled fuel to prevent odor or fire hazards. 6. Clean the louvers: Use a damp cloth to wipe off dust and stains from the louvers. Regular cleaning will prevent the buildup of dirt and make future cleaning easier. If the automatic cleaning mode still does not function properly after following these steps, it is recommended to consult your dealer for further assistance.
If the room temperature measurements behind the Toyotomi LC-32F heater are not accurate, you can try the following steps to troubleshoot the issue: 1. Check the placement of the heater: Ensure that the heater is placed in an appropriate location. Avoid placing it near drafts, windows, or doors, as these can affect the accuracy of the room temperature measurements. Also, make sure that the heater is not obstructed by furniture or other objects that may block the airflow. 2. Verify the distance from the wall: The manual recommends maintaining a distance of at least 50 cm between the back of the heater and the wall. This allows for proper air circulation and accurate temperature measurements. Check if the heater is positioned at the recommended distance from the wall. 3. Clean the temperature sensor: The room temperature measurements are taken by a sensor located behind the heater. Dust or dirt accumulation on the sensor can affect its accuracy. Gently clean the sensor using a soft cloth to remove any debris. 4. Monitor the temperature in the room: Use a separate thermometer placed away from the heater to compare the room temperature readings. If there is a significant difference between the readings, it may indicate an issue with the temperature sensor or the heater itself. If the room temperature measurements continue to be inaccurate after following these steps, it is recommended to consult your dealer for further assistance.
Yes, the manual of the Toyotomi LC-32F is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Toyotomi and is the answer not in the manual?
Question and answer
Number of questions: 3مشكيلة في hhh4
مشكيلة hhh4
Error. Hhh4 help