Suprema BioEntry R2 manual

Suprema BioEntry R2
6 · 1
PDF manual
 · 29 pages
English
manualSuprema BioEntry R2
8
Introduction

How to enroll a fingerprint

In order to improve the fingerprint authentication rate, register the fingerprint correctly. BioEntry R2 can recognize a fingerprint even if the angle and position of a user’s fingerprint input change. If you register the fingerprint with attention to the following matters, the authentication rate can be improved.
Selecting a finger for fingerprint input
In preparation for the case that the fingerprint of a specific finger cannot be used, for example if the user is lifting a load with one hand or a finger gets hurt, up to 10 fingerprints for each user can be registered.
In the case of a user whose fingerprint cannot be recognized well, the authentication rate can be improved by enrolling the same finger twice repeatedly.
If a finger has a cut or the fingerprint is blurry, select another finger for the fingerprint.
It is recommended to use the index finger or the middle finger when scanning the fingerprint. The authentication rate can be reduced if it is difficult to place another finger at the center of fingerprint sensor accurately.
Fingerprint enroll method
1
Place the finger with the fingerprint to be registered on the fingerprint sensor and press the finger gently for better authentication.
2
After a beep sounds, scan the fingerprint of the registered finger again. (scan the fingerprint of a finger to be registered twice)
Cautions for enrolling a fingerprint
When a fingerprint is recognized, it is compared with the initially registered fingerprint, so the initial fingerprint
enroll is the most important. Pay attention to the following matters when enrolling the fingerprint.
Place the finger deep enough to contact with the sensor completely.
Place the center of the fingerprint in the center of the sensor.
If a finger has a cut or the fingerprint is blurry, select another finger for the fingerprint.
Scan the fingerprint correctly without moving according to the instruction on the screen.
If you make the finger upright so that the contact area with the sensor is decreased or the angle of finger is
warped, fingerprint authentication may not be performed.
When the fingerprint recognition fails
BioEntry R2 can recognize a fingerprint regardless of a change of season or finger condition. However, the
authentication rate may vary according to the external environment or fingerprint input method.
If the fingerprint authentication cannot be done smoothly, it is recommended to take the following measures.
If the finger is smeared with water or sweat, dry off the finger and then scan the finger.
If the finger is too dry, blow your breath on the fingertips and then scan the finger.
If the finger has a cut, register the fingerprint of another finger.
The initially enrolled fingerprint often may have not been scanned correctly, so enroll the fingerprint again
according to ‘Cautions for enrolling a fingerprint’.

Manual

View the manual for the Suprema BioEntry R2 here, for free. This manual comes under the category security access control systems and has been rated by 1 people with an average of a 6. This manual is available in the following languages: English. Do you have a question about the Suprema BioEntry R2 or do you need help? Ask your question here

Need help?

Do you have a question about the Suprema and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Suprema BioEntry R2 specifications

Below you will find the product specifications and the manual specifications of the Suprema BioEntry R2.

General
BrandSuprema
ModelBioEntry R2 | BER2OD
Productsecurity access control system
LanguageEnglish
FiletypeInstallation Guide (PDF), User manual (PDF)
Technical details
TypeIntelligent access control reader
Authentication typeAccess chip/card, Biometric
CertificationCE, FCC, KC, REACH, WEEE
Access code readerNo
Fingerprint readerYes
Access chip/card readerYes
Product colorBlack, Grey
RFID frequency13.56 MHz
Ports & interfaces
PC connectedYes
PC connectionRS-485
RS-485 ports1
Operational conditions
Operating relative humidity (H-H)0 - 80 %
Operating temperature (T-T)-20 - 50 °C
Sustainability
Sustainability certificatesRoHS
Weight & dimensions
Weight158 g
Width50 mm
Depth37.5 mm
Height164 mm
Display
Built-in displayNo
Camera
Front cameraNo
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Suprema BioEntry R2 below.

What is the weight of the Suprema BioEntry R2?

The Suprema BioEntry R2 has a weight of 158 g.

What certifications does the Suprema BioEntry R2 have?

The Suprema BioEntry R2 has the following certifications: CE, FCC, KC, REACH, WEEE.

What is the height of the Suprema BioEntry R2?

The Suprema BioEntry R2 has a height of 164 mm.

What is the width of the Suprema BioEntry R2?

The Suprema BioEntry R2 has a width of 50 mm.

What is the depth of the Suprema BioEntry R2?

The Suprema BioEntry R2 has a depth of 37.5 mm.

Is the manual of the Suprema BioEntry R2 available in English?

Yes, the manual of the Suprema BioEntry R2 is available in English .

Is your question not listed? Ask your question here

No results