Suprema BioEntry R2 manual

Suprema BioEntry R2
6 · 1
PDF manual
 · 29 pages
English
manualSuprema BioEntry R2
11
Installation

Power supply connection

2 1
1
4
UPS
(Optional)
BioEntry R2
Power supply connection
1 - PWR +VDC Red (white stripe)
2 - PWR GND Black (white stripe)
DC power
Use the IEC/EN 62368-1 approved power adapter that supports higher power consumption than the product.
If you wish to connect and use another device to the power supply adapter, you should use an adapter with a
current capacity which is the same or larger than the total power consumption required for the terminal and
another device.
Refer to the Power in the product specifications for maximum current consumption specifications.
DO NOT extend the length of power cable when using the power adapter.
Use a separate power supply for Secure I/O 2, the electric lock, and the BioEntry R2 respectively. If connecting
and using the power supply to these devices together, the devices may malfunction.
Use an AWG24 twisted pair with a maximum length of 1.2 km for the RS-485 cable.
If connecting with a RS-485 daisy chain, connect the termination resistor (120 Ω) to both ends of the daisy
chain connection. If connected to the middle line, the signal level becomes smaller and the communication
performance will deteriorate. Make sure to connect it to both ends of the daisy chain connection.
If Xpass is connected to the master device, only card authentication can be used.
RS-485 connection
1 - 485 TRXP Blue
2 - 485 TRXN Yellow
3 - 485 GND Black
4 - SH GND Gray

Manual

View the manual for the Suprema BioEntry R2 here, for free. This manual comes under the category security access control systems and has been rated by 1 people with an average of a 6. This manual is available in the following languages: English. Do you have a question about the Suprema BioEntry R2 or do you need help? Ask your question here

Need help?

Do you have a question about the Suprema and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Suprema BioEntry R2 specifications

Below you will find the product specifications and the manual specifications of the Suprema BioEntry R2.

General
BrandSuprema
ModelBioEntry R2 | BER2OD
Productsecurity access control system
LanguageEnglish
FiletypeInstallation Guide (PDF), User manual (PDF)
Technical details
TypeIntelligent access control reader
Authentication typeAccess chip/card, Biometric
CertificationCE, FCC, KC, REACH, WEEE
Access code readerNo
Fingerprint readerYes
Access chip/card readerYes
Product colorBlack, Grey
RFID frequency13.56 MHz
Ports & interfaces
PC connectedYes
PC connectionRS-485
RS-485 ports1
Operational conditions
Operating relative humidity (H-H)0 - 80 %
Operating temperature (T-T)-20 - 50 °C
Sustainability
Sustainability certificatesRoHS
Weight & dimensions
Weight158 g
Width50 mm
Depth37.5 mm
Height164 mm
Display
Built-in displayNo
Camera
Front cameraNo
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Suprema BioEntry R2 below.

What is the weight of the Suprema BioEntry R2?

The Suprema BioEntry R2 has a weight of 158 g.

What certifications does the Suprema BioEntry R2 have?

The Suprema BioEntry R2 has the following certifications: CE, FCC, KC, REACH, WEEE.

What is the height of the Suprema BioEntry R2?

The Suprema BioEntry R2 has a height of 164 mm.

What is the width of the Suprema BioEntry R2?

The Suprema BioEntry R2 has a width of 50 mm.

What is the depth of the Suprema BioEntry R2?

The Suprema BioEntry R2 has a depth of 37.5 mm.

Is the manual of the Suprema BioEntry R2 available in English?

Yes, the manual of the Suprema BioEntry R2 is available in English .

Is your question not listed? Ask your question here

No results