SpeakerCraft IRE 3.0 manual

SpeakerCraft IRE 3.0
7.4 · 1
PDF manual
 · 2 pages
English
manualSpeakerCraft IRE 3.0
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-3.0 • LINEAR P/N: 223105B • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 14.000” FOLD TO 4.250” X 3.500”
• FOLDING: 4 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223105B • IMAGE 1

DESCRIPTION

The IRE-3.0 represents the highest level in sophistication for attachable
IR Emitters. It features a unique EZ-Docker
port that permits instant
removal of the emitter when rearranging or servicing components. It
flashes visible red when emitting IR control signals. It has 75% lower
IR output than non-visible emitters and therefore should be used
when controlling multi-zone components to avoid cross-zone interac
-
tion. An improved adhesive reduces callbacks for reattachment of
“fallen emitters”.

ATTACHMENT

First, locate the component’s IR Sensor window (See Note 1) and
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker
port has a clear adhesive layer on its bottom
surface. Peel the protec
-
tive layer off, exposing
the adhesive.
Orient the port vertical
(see Fig. 2) and press
it over the center of the
component’s sensor
window. Press & hold
for several seconds to
ensure maximum contact
of the adhesive.
Slide the emitter from the
top down, into the EZ-
Docker
port. You should
feel it “snap” into place.
IRE-3.0
Emitter with
Visible LED
8 FT
9/16"
7/16"
3.5mm
mini plug
1/4"
Side View
Emitter
Wire Lead
Dockin
g
Por
t
Clear Adhesive Tape
(See Note 3)
Top View
NOTE: White striped
side is positive ( +)
(
)
(+
)
Emitter slides into
Docking Por
t

Fig. 1

TYPICAL INSTALLATION
Satellite Receiver
A/V Receiver
PS-1.0
IRE-3.0
Emitter w/
Visible LED
IRE-3.0
Emitter w/
Visible LED
IRE-3.0
Emitter w/
Visible LE
D
VCR

Hand Held

Remote

IRC-3.0

IR Sensor
Window

AT-1. 0

Amplified Terminator
Unit
Power Supply
120V AC
(unswitched)
Shelf Top
IR Receiver

Fig. 3

Fig. 1

(To remove the emitter at any time, simply push upward until it
“pops” out).
Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-3.0 shell.
Note 3: If you need to remove the EZ-Docker
port or emitter
previously stuck to a component’s surface, use a fresh adhesive
(included) before reattaching.

Fig. 3

IR Controlled Components

IR sensor

window

Docking Por

t

IRE-3.0 attached to

IR sensor window

2) Slide IRE-3.0 Emitter

end into docking por

t

1) Attach IRE-3.0 Docking Port to

IR sensor window with adhesive pad

Fig. 2

Fig. 2

s

View the manual for the SpeakerCraft IRE 3.0 here, for free. This manual comes under the category Remote Controllers and has been rated by 1 people with an average of a 7.4. This manual is available in the following languages: English. Do you have a question about the SpeakerCraft IRE 3.0 or do you need help? Ask your question here

Need help?

Do you have a question about the SpeakerCraft and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other SpeakerCraft owners to provide you with a good answer.

Number of questions: 0

General
SpeakerCraft
IRE 3.0 | ELT03300
Remote Controller
English
User manual (PDF)
Weight & dimensions
Cable length2.4 m
Design
Product colourBlack
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the SpeakerCraft IRE 3.0 below.

Is your question not listed? Ask your question here

No results