SpeakerCraft IRE-2.0 manual

SpeakerCraft IRE-2.0
8.7 · 1
PDF manual
 · 2 pages
English
manualSpeakerCraft IRE-2.0
PRINTER’S INSTRUCTIONS:INSTR,INSTL,IRE-2.0 • LINEAR P/N: 223109B • INK: BLACK •MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.25” X 17.500” FOLD TO 4.250” X 3.500”• FOLDING: 5 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1223109B • IMAGE 1

DESCRIPTION

The IRE-2.0 is the dual emitter version of the IRE-1.0. It features a
unique EZ-Docker
port that permits instant removal of the emitter
when rearranging or servicing components. An improved adhesive
reduces callbacks for reattachment of “fallen emitters”. The case may
also be taken apart so that the tiny internal emitter can be placed
inside a component, when desired. High IR output from the top
curved surface allows emitter to be mounted on a nearby surface,
below, above or on a cabinet door, rather than directly on the sensor
of the unit where conditions permit.

ATTACHMENT

First, locate the component’s IR Sensor window (see Note 1) and
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker
port has a clear adhesive layer on its bottom surface.
Peel the protective layer
off, exposing the adhesive.
Orient the port vertical (see
Fig. 2) and press it over the
center of the component’s
sensor window. Press &
hold for several seconds to
ensure maximum contact
of the adhesive.
Insert the 3.5mm plug
into an Emitter jack on a
SpeakerCraft Terminator or
other source of IR (see Fig.
3). Slide the emitter from
the top down, into the EZ-
Docker
port.
IRE-2.0Dual Emitter
8 FT
9/16 "
7/16 "
3.5mm mini plugEmitters & Docking Ports
7/16 "
( )
(+)
Top ViewNOTE: White stripedside is positive ( +
)
1/4"
Side View
Emit ter
Emit ter slides int o
Dock ing Port
Wire Lead
Dock ing
Port
Clea r Adhesive Tap e
(See Note 3)
TYPICAL INSTALLATIONSatellite ReceiverPS-1.0IRE-2.0 Dual EmitterIRE-2.0 Dual EmitterIRE-1.0 EmitterA/V Receiver
VCR

Hand Held

Remote

IRC-3.0

IR SensorWindow

AT-1.0

Amplified Terminator
Unit
Shelf TopIR ReceiverPower Supply120V AC(unswitched)

Fig. 3

Fig. 1

You should feel it “snap” into place. (To remove the emitter at any
time, simply push upward until it “pops” out).
Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-2.0 shell.
Note 3: If you need to remove the EZ-Docker
port or emitter previ-
ously stuck to a component’s surface, use a fresh adhesive (included)
before reattaching.

Fig. 3

IR Controlled Components

IR sensor

window

Docking Port

IRE-2.0 attached to

IR sensor window

2) Slide IRE-2.

0 Emitter

end into docking port

1) Attach

IRE-2.0 Docking Port

to IR sensor window with adhesive pa

d

Fig. 2

Fig. 2

View the manual for the SpeakerCraft IRE-2.0 here, for free. This manual comes under the category Receivers and has been rated by 1 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the SpeakerCraft IRE-2.0 or do you need help? Ask your question here

Need help?

Do you have a question about the SpeakerCraft and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other SpeakerCraft owners to provide you with a good answer.

Number of questions: 0

General
SpeakerCraft
IRE-2.0 | ELT03200
Receiver
English
User manual (PDF)
Other features
Antenna typeIR
Technical details
Cable length2.4 m
Product colourBlack
Ports & interfaces
Connectivity technologyWireless
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the SpeakerCraft IRE-2.0 below.

Is your question not listed? Ask your question here

No results