SpeakerCraft IRE-1.0 manual

SpeakerCraft IRE-1.0
8.7 · 1
PDF manual
 · 2 pages
English
manualSpeakerCraft IRE-1.0
PRINTER’S INSTRUCTIONS:INSTR,INSTL,IRE-1.0 • LINEAR P/N: 223101X20 • INK: BLACK •MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 17.500” FOLD TO 4.250” X 3.500”• FOLDING: 5 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1223101X20 • IMAGE 1

DESCRIPTION

The IRE-1.0 represents the highest level in sophistication for attachable
IR Emitters. It features a unique EZ-Docker
port that permits instant
removal of the emitter when rearranging or servicing components.
An improved adhesive reduces callbacks for reattachment of “fallen
emitters”. The case may also be taken apart so that the tiny internal
emitter can be placed inside a component, when desired. High IR
output from the top curved surface allows emitter to be mounted
on a nearby surface, below, above or on a cabinet door, rather than
directly on the sensor of the unit where conditions permit.

ATTACHMENT

First, locate the component’s IR sensor window (see Note 1) and
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker
port has a clear adhesive layer on its bottom surface.
Peel the protective layer off,
exposing the adhesive.
Orient the port vertical (see
Fig. 2) and press it over the
center of the component’s
sensor window. Press and
hold for several seconds to
ensure maximum contact
of the adhesive.
Slide the emitter from the
top down, into the EZ-
Docker
port. You should
feel it “snap” into place. (To
remove the emitter at any
time, simply push upward
until it “pops” out).
IRE-1.0Emitter
8 FT
9/16"
7/16"
3.5mm mini plug
1/4"
Side View
Emitter
Wire Lead
Docking
Port
Clear Adhesive Tape
(See Note 3)
Top ViewNOTE: White stripedside is positive ( +
)
(
)
(+
)
Emitter slides into
Docking Port
TYPICAL INSTALLATION
Satellite ReceiverPS-1.0IRE-1.0IRE-1.0 EmitterIRE-1.0 Emitter
VCR
A/V ReceiverHand HeldRemote

IRC-3.0

EmitterIR SensorWindow

AT-1.0

Amplified Terminator

Unit
Power Supply120V AC(unswitched)

Shelf Top

IR Receiver

Fig. 1

Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-1.0 shell.
Note 3: If you need to remove the EZ-Docker
port or emitter previ-
ously stuck to a component’s surface, use a fresh adhesive (included)
before reattaching.
Note 4: The emitter shell and EZ-Docker
port, though dark in
appearance, are transparent to Infrared. This allows IR commands
to pass through them, permitting local hand held remote control as
well as through the IRE-1.0.

Fig. 3

IR Controlled Components

IR sensor

window

Docking Port

IRE-1.0 attached to

IR sensor window

2) Slide IRE-1.0 Emitter

end into docking port

1) Attach IRE-1.0 Docking Port

to IR sensor window with adhesive pad

Fig. 2

s

View the manual for the SpeakerCraft IRE-1.0 here, for free. This manual comes under the category Remote Controllers and has been rated by 1 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the SpeakerCraft IRE-1.0 or do you need help? Ask your question here

Need help?

Do you have a question about the SpeakerCraft and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other SpeakerCraft owners to provide you with a good answer.

Number of questions: 0

General
SpeakerCraft
IRE-1.0 | ELT03100
Remote Controller
English
User manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the SpeakerCraft IRE-1.0 below.

Is your question not listed? Ask your question here

No results