Sony ICF-CS10iP manual

Sony ICF-CS10iP
7.9 · 3
PDF manual
 · 2 pages
English
manualSony ICF-CS10iP
Owner’s Record
e model number and the serial number are located on the
bottom.
Record the serial number in the space provided below. Refer
to them whenever you call upon your Sony dealer regarding
this product.
Model No. ICF-CS10iP
Serial No. ________________________________
For customers who purchased this product in the
USA
Please register this product on line at
http://www.sony.com/productregistration.
Proper registration will enable us to send you
periodic mailings about new products, services,
and other important announcements. Registering
your product will also allow us to contact you
in the unlikely event that the product needs
adjustment or modication. ank you.
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or
moisture.
To reduce the risk of fire, do not cover the
ventilation of the apparatus with newspapers,
tablecloths, curtains, etc. And do not place lighted
candles on the apparatus.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing,
and do not place objects filled with liquids, such
as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or
batteries installed) to excessive heat such as
sunshine, fire or the like for a long time.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main plug
from the AC outlet immediately.
The unit is not disconnected from the AC power
source (mains) as long as it is connected to the
wall outlet, even if the unit itself has been turned
off.
The nameplate and important information
concerning safety are located on the bottom
exterior.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same type.
is symbol is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sucient magnitude to constitute
a risk of electric shock to persons.
is symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving
antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
WARNING

Replace the battery for the clock backup with a
Sony CR2032 lithium battery, and the battery
for the remote commander with a Sony CR2025
lithium battery. Use of another battery may
present a risk of fire or explosion.

Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.

Dispose of used battery promptly. Keep away
from children.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
For the state of california, USA only
Perchlorate Material –special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate
Precautions

Play the unit on the power source specified in
“Specifications.

Since a strong magnet is used for the speaker,
keep personal credit cards using magnetic coding
or spring-wound watches away from the unit to
prevent possible damage from the magnet.

Do not leave the unit in a location near a heat
source such as a radiator or airduct, or in a
place subject to direct sunlight, excessive dust,
mechanical vibration, or shock.

Allow adequate air circulation to prevent internal
heat build-up. Do not place the unit on a surface
(a rug, a blanket, etc.) or near materials (a
curtain) which might block the ventilation holes.

Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by qualified
personnel before operating it any further.

To clean the casing, use a soft cloth dampened
with a mild detergent solution.

Never touch the wire of the external FM
antenna during a thunderstorm. Furthermore,
immediately disconnect the AC power cord
from the radio.
NOTES ON LITHIUM BATTERY

Wipe the battery with a dry cloth to assure a
good contact.

Be sure to observe the correct polarity when
installing the battery.

Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
If you have any questions or problems concerning
your unit, please consult your nearest Sony dealer.
Features
Clock Radio compatible with iPod®/iPhone®
Wake or Sleep to iPod/Radio/Buzzer
Easy to set A-B alarm
2-5-7day alarm
LCD Brightness control
MEGA BASS
MEGA Xpand
Wireless Remote Commander
No Power No Problem alarm system to keep
the clock and the alarm operating during a
power interruption with a CR2032 battery
installed
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 6 ohm loads both channels driven, from
150 Hz -10,000 Hz; rated 3 watts per channel
minimum RMS power, with no more than 10 %
total harmonic distortion.
Time display
12-hour system
Section for iPod
DC out: 5V
MAX: 500mA
Radio section
Frequency range
Band Frequency Channel step
FM 87.5 MHz – 108 MHz 0.1 MHz
AM 530 kHz – 1 710 kHz 10 kHz
General
Speaker
Approx. 5.7 cm (2
1
/
4
inches) dia. 6 Ω
Input
AUDIO IN jack (ø 3.5 mm stereo minijack)
Power output
3.5 W + 3.5 W (at 10% harmonic distortion)
Power requirements
120 V AC, 60 Hz
For clock back up: 3V DC, CR2032 battery (1)
Dimensions
Approx. 290.5 mm × 152.0 mm × 139.5 mm (w/h/d)
(11
3
/
8
inches × 5
15
/
16
inches × 5
1
/
2
inches)
including projecting parts and controls
Mass
Approx. 1.94 kg (4 lb 4 oz) including power
supply unit
Supplied accessories
Remote commander (1)
AM loop antenna (1)
Audio connecting cable (1)
Universal Dock Adapter for iPhone (1)
Universal Dock Adapter for iPhone 3G & iPhone
3GS (1)
Universal Dock Adapter for iPhone 4 (1)
Design and specifications are subject to change
without notice.
4-150-697-13(2)
This unit includes a preinstalled Sony Lithium battery (CR2032) as back-up power source for the clock, which is preset
to EST (Eastern Standard Time) at the factory. And this battery is considered part of the product.
Connecting the
antenna
To connect the AM loop antenna
The shape and the length of the antenna is
designed to receive AM signals. Do not dismantle
or roll up the antenna.
1 Remove only the loop part from the plastic stand.2 Set up the AM loop antenna.3 Insert the AM antenna terminal into the AM ANTENNA jack on the rear of the unit.To remove the AM loop antenna
Pull the AM antenna terminal while pushing up
the terminal clamp.
Adjusting the AM loop antenna
Find a place and an orientation that provide good
reception.

Do not place the AM loop antenna near the
unit or other AV equipment, as noise may
result.
Tip
Adjust the direction of the AM loop antenna for
best AM broadcast sound.
Preparing the remote
commander
Before using the card remote commander for the
first time, remove the insulation film.
To know when to replace the battery
With normal use, the battery (CR2025) should
last for about six months. When the remote
commander no longer operates the unit, replace
the battery with a new one.
CR2025
Compatible iPod/iPhone models
Compatible iPod/iPhone models are as follows.
Update your iPod/iPhone to use the latest software
before you use it.
iPod nano
3rd generation
(video)
iPod classic
iPod
4th generation
iPod touch
1st generation
iPhone 4
iPhone
iPod nano
1st generation
iPod
4th generation
(color display)
iPhone 3G
iPod nano
4th generation
(video)
iPod touch
2nd generation
iPod nano
2nd generation
(aluminum)
iPod
5th generation
(video)
iPod mini
iPod nano
5th generation
(video camera)
iPhone 3GS
iPod touch
3rd generation
Notes

In these Operating Instructions, “iPod” is used
as a general reference to iPod functions on an
iPod or iPhone, unless otherwise specified by
the text or illustrations.

The connector of the unit is for sole use with an
iPod. If you use devices that do not match with
the connector, connect to the AUDIO IN jack of
this unit with the supplied audio connecting
cable.

Sony cannot accept responsibility in the event
that data recorded to an iPod is lost or damaged
when using an iPod connected to this unit.
Troubleshooting
Should any problem persist after you have made
the following checks, consult your nearest Sony
dealer.
The clock flashes AM 12:00” due to a power
interruption.

The battery is low. Replace the battery. Remove
the old battery and install a new one.
The radio, iPod or buzzer alarm does not
sound at the preset alarm time.

Check that alarm “A” or alarm “B” is properly
displayed.
The radio or alarm of iPod is activated but no
sound comes on at the preset alarm time.

Check the alarm volume setting.
There is no sound from the iPod.

Make sure the iPod is securely connected.

Adjust the VOLUME.
The iPod cannot be operated with this unit.

Make sure the iPod is securely connected.
The iPod cannot be charged.

Make sure the iPod is securely connected.
When Daylight Saving Time (summer time)
begins, the clock does not employ the
Daylight Saving Time automatically.

Make sure the clock is set correctly.

Press and hold CLOCK and SNOOZE/DATE/
SLEEP OFF simultaneously for at least
2 seconds to activate the Automatic DST
function.
Notes

Do not attempt to charge the battery.

If you are not going to use the remote
commander for a long time, remove the battery
to avoid any damage that may be caused by
leakage and corrosion.
About the backup
battery
To keep accurate time, this unit contains a
CR2032 battery as a backup power source.
The battery keeps the clock and the alarm
operating in the event of a power interruption.
To know when to replace the battery
When the battery becomes weak, “” appears in
the display.
If a power interruption occurs while the battery is
weak, the current time and alarm will be erased.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may cause a fire or
explosion.
Note
If “AM 12:00” flashes in the display when the unit
is connected to an AC outlet for the first time, the
battery may be weak. In this case, consult your
Sony dealer.
To replace the battery1 Keep the AC plug connected to the AC outlet, remove the screw that secures the battery compartment lid at the bottom of the unit using a screwdriver, and open the lid (see Fig. ).2 Insert a new battery in the battery compartment with the side facing up (see Fig. ).3 Close the battery compartment lid and secure it with the screw (see Fig. ).
4 Press iPod & iPhone , RADIO
BAND, AUDIO IN or SNOOZE/DATE/SLEEP OFF to turn “” off in the display.
Note
When you replace the battery, do not disconnect
the plug from the AC outlet. Otherwise, the
calendar, current time, alarm and station presets
will be erased.
Reset button
CR2032
If the time in the display is incorrect after the battery is changed (Reset)
Press the reset button with a pointed device. The
reset button is in the small hole located in the
battery compartment (see Fig. ).
©2009 Sony Corporation Printed in China

FM/AM

Clock Radio

No Power No Problem is a trademark of Sony Corporation.

ICF-CS10iP

Operating Instructions

Dream Machine is a trademark of Sony Corporation.
s

View the manual for the Sony ICF-CS10iP here, for free. This manual comes under the category Clock Radio and has been rated by 3 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Sony ICF-CS10iP or do you need help? Ask your question here

Need help?

Do you have a question about the Sony and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Sony owners to provide you with a good answer.

Lance • 14-1-2022No comments

Show me how to turn and or power button on my Sony fm and am clock radio model no icf- cs101p by video now

Answer this question
Ranga reddy • 11-10-2021No comments

Which type of power adapter to be used ?what are the voltage required

Answer this question

Number of questions: 2

General
Sony
ICF-CS10iP | ICF-CS10IP
Clock Radio
0027242773318
English
User manual (PDF)
Audio
Audio output channels2.0 channels
RMS rated power7 W
Frequency range- Hz
Impedance6 Ω
Driver diameter570 mm
Ports & interfaces
Headphone connectivity3.5 mm
Bluetooth
Radio
FM radio
Preset stations quantity10
Supported radio bandsAM,FM
Display
DisplayLCD
Other features
Clock/Date display
Backlight
Dimensions (WxDxH)290.5 x 139.5 x 152 mm
Compatible productsiPod touch\niPod nano\niPod\niPod mini\niPod classic\niPhone 4\niPhone 3GS\niPhone 3G\niPhone
Performance
Apple docking compatibilityiPad,iPhone,iPod
Alarm clock
Bass adjustment
Sleep timer
Equalizer
Power
Built-in charger
AC input voltage120 V
AC input frequency60 Hz
Battery typeCR2032, CR2025
Weight & dimensions
Weight1940 g
Packaging content
Manual
AC adapter included
Quick start guide
Design
Product colourBlack
Indication light
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Sony ICF-CS10iP below.

Is your question not listed? Ask your question here

No results