Sony ICF-C414 manual

Sony ICF-C414
8.7 · 5
PDF manual
 · 2 pages
English
manualSony ICF-C414
English
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
To reduce the risk of fire, do not cover the
ventilation of the apparatus with newspapers,
tablecloths, curtains, etc. And do not place lighted
candles on the apparatus.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing,
and do not place objects filled with liquids, such
as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or
batteries installed) to excessive heat such as
sunshine, fire or the like for a long time.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main plug
from the AC outlet immediately.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
Features

Large, easy to-see, 1.4 inch green LED.

Dual alarm FM/AM Clock radio.

Various types of alarms — buzzer, radio and
melody.

Automatic time set — When you plug the clock
in for the first time, the current time will be
shown in the display.

Automatic Daylight Saving Time/Summer time
adjustment.

Date button to display month, day and year.

Brightness control (High/Middle/Low).

No Power No Problem™ alarm system to keep
the clock and the alarm operating during a
power interruption with a CR2032 battery
installed.

Extendable snooze — Snooze time can be
extended from 10 up to 60 minutes.

Progressive Alarm Speed (buzzer only).
About the backup
battery
To keep good time, as backup power source, this
unit has one CR2032 battery inside of the unit in
addition to the house current.
The battery keeps the clock and the alarm
operating in the event of a power interruption.
Note for customers in Canada
The clock is preset at the factory, and its memory
is powered by the preinstalled Sony CR2032
battery. If the “AM 12:00” appears on the display
when the unit is connected to AC outlet for the
first time, the battery may be weak. In this case,
consult a Sony dealer. The preinstalled CR2032
battery is considered part of the product, and is
covered by the warranty. You are required to show
“Note for customers in Canada” (in this
instruction) to a Sony dealer in order to validate
the warranty for this product.
Knowing when to replace the battery
When the battery becomes weak, the “
indicator appears in the display.
In the event of a power interruption when the
battery is weak, the current time and alarm will
be initialized.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may present a risk
of fire or explosion.
Installing and replacing the backup battery1 Keep the AC plug connected to the AC outlet, remove the screw that secures the battery compartment at the rear of the unit using a screwdriver, and remove the battery compartment (See Fig. -).2 Insert a new battery in the battery compartment with the side facing up. To remove the battery from the battery compartment, push it out from the side marked PUSH (See Fig. -).3 Insert the battery compartment back into the unit and secure it with the screw (See Fig. -).4 When you are replacing the battery, press RADIO ON to turn the “
” indicator off in the display.
Notes

If you replace the battery, do not disconnect the
AC plug from the AC outlet.
Otherwise, the current time and alarm will be
initialized.

Be sure to observe the correct polarity when
installing the battery.
Setting the clock for
the first time
This unit is preset to the current date and time at
the factory, and is powered by the back up battery.
All you need to do is just plug it in and select your
time zone.
1 Plug in the unit.
First, the month and date appear, then the
year, and then the current Eastern Standard/
Daylight Time appears in the display.
2 Press TIME ZONE.
Area number “2” appears in the display.
If you live in the Eastern Time zone, you do
not need to adjust the area setting.
Area number Time zone
1 Atlantic Standard/
Daylight Time
2
(default)
Eastern Standard/
Daylight Time
3 Central Standard/
Daylight Time
4 Mountain Standard/
Daylight Time
5 Pacific Standard/Daylight
Time
6 Yukon Standard/Daylight
Time
7 Hawaiian Standard/
Daylight Time
3 Press TIME ZONE repeatedly until the desired number appears.
The display returns to the clock about 4
seconds after the operation is complete.
Note
During the shipment and your first use, a clock
error may occur. In this case, refer to “Setting the
clock and date” to set the correct time.
When daylight saving time (summer time) begins
This unit employs Automatic Daylight Saving
Time/Summer Time adjustment. The DST
indicator appears in the display at the beginning
of the daylight saving time (summer time), and
disappears at the end of it.

Daylight saving time begins at: 2:00 AM on the
second Sunday of March.

Standard time begins at: 2:00 AM on the first
Sunday of November.
To cancel the automatic DST/summer time adjustment and to set DST display manually
The automatic DST/summer time adjustment can
be cancelled.
Press and hold DST for at least 3 seconds while
the clock is displayed.
A beep sounds, and “Aut
OFF” appears in the
display to show that the automatic DST/summer
time adjustment is cancelled. The display returns
to the clock.
Notes

Daylight Saving Time depends on the law in
each country/region, and your area may not use
it. In such a case, cancel the automatic DST/
summer time adjustment before using the set
and set the time manually as necessary.

To activate the automatic DST/summer time
adjustment again, press and hold DST for at
least 3 seconds. A beep sounds, and “Aut
On” appears in the display to show that the
automatic DST/summer time adjustment is
activated. The display returns to the clock.

To change the display to the daylight saving
time (summer time) manually, see “To change
the display to the daylight saving time (summer
time) indication.
Setting the clock and
date
To change the setting manually, follow the
procedure from step 1.
1 Press CLOCK for at least 2 seconds.
You will hear a beep and the year will start to
flash in the display.
2 Press + or until the correct year appears in the display.3 Press CLOCK.
4 Repeat steps 2 and 3 to set the month,
day and time.
After setting the time, two short beeps sound
and the clock starts from 0 seconds.

Pressing and holding + or changes the year,
month or day rapidly.
When setting the current time, time changes
rapidly by 1 minute-increments up to 10
minutes, and then by 10 minute-increments.

While setting the clock, you must perform each
step within 65 seconds, or the clock setting
mode will be cancelled.
To display the year and date
Press SNOOZE/DATE/SLEEP OFF once for the
date, and within about 3 seconds press it again for
the year.
The display shows the date or year for about 3
seconds and then changes back to the current
time.
If you connect the AC plug to an AC outlet while
this unit is powered from the backup power
source, the current date and time appears in the
following order (the same as when the unit is
powered on after a power interruption).
“month and date” (about 1 second)
“year”
(about 1 second)
current time
To change the display to the daylight saving time (summer time) indication
Change the daylight saving time (summer time)
adjustment setting according to the following
procedures if you have cancelled the automatic
DST/summer time adjustment.
Press DST.
The DST indicator appears in the display and the
time indication changes to the daylight saving
time (summer time).
To deactivate the daylight saving time (summer
time) adjustment, press DST again.
Setting the brightness
of the display
Three levels of brightness are available by pressing
BRIGHTNESS.
Playing the radio
1 Press RADIO ON to turn on the radio.2 Adjust the volume using VOLUME.3 Select BAND.4 Tune in to a station using TUNING.To turn off the radio
Press RADIO OFF/ALARM RESET.
Improving the reception
FM:
The AC power cord functions as an FM
antenna. Extend the AC power cord fully to
increase reception sensitivity.
AM:
Rotate the unit horizontally for optimum
reception. A ferrite bar AM antenna is built-in
to the unit.
Do not operate the unit over a steel desk or metal
surface, as this may lead to interference of
reception.
Setting the alarm
The dual alarm function allows you to set two
alarm programs (ALARM A and ALARM B).
The alarm time can be set for each program and
the alarm sound is selectable from buzzer, radio
or melody.
Notes

Before setting the alarm, make sure to set the
clock (see “Setting the clock and date”).

The factory set alarm time is “PM 12:00”.

To set the radio alarm, first tune in to a station
and adjust the volume (see “Playing the radio”).
To set the alarm time1 Set ALARM A (or B) to the desired alarm sound ( (buzzer), RADIO or MELODY).
The alarm time appears for a few seconds, and
then the ALARM A (or B) indicator lights up
in the display. (It does not appear when the
switch is set to OFF.)
When you set the alarm to MELODY, the
alarm sounds the melody- “Spring” from “The
Four Seasons” by Antonio Lucio Vivaldi.
2 Press ALARM TIME SET A (or B) + or
to set the desired time.
Each press of ALARM TIME SET A (or B) + or
changes the indication by 1 minute. If you
press and hold ALARM TIME SET A (or B) +
or , the alarm time goes forward (or
backward) by 1 minute up to 10 minutes, and
then by 10 minutes increments. While setting
the alarm time, the ALARM A (or B) indicator
flashes in the display. The following example is
when setting the ALARM A.
When the alarm time setting is complete, the
display returns to the clock after a few seconds
and the ALARM A (or B) indicator changes
from flashing to fully lit.

While ALARM A (or B) is set to , RADIO
or MELODY, the alarm time setting can be
changed by ALARM TIME SET A (or B) + or .
One press of ALARM TIME SET A (or B) + or
displays the alarm time for about 4 seconds. By
pressing ALARM TIME SET A (or B) + or
while the alarm time appears in the display, the
alarm time will be changed.

For the buzzer alarm, the beeping of the alarm
becomes more rapid after every few seconds in
three progressive stages.

The ALARM A (or B) indicator flashes in the
display while:
– The alarm time appears in the display.
– The alarm sounds.
– The snooze function is turned on.

The alarm time setting cannot be changed if
ALARM A (or B) is set to OFF. If you press
ALARM TIME SET A (or B) + or , “OFF”
appears in the display for about 0.5 seconds.

If a second alarm sounds during a first (or the
snooze function is active), the second alarm
takes priority.

CLOCK, DST, and TIME ZONE are unavailable
while the alarm sounds or when the snooze
function is turned on.

The alarm function works as usual at the first
and last day of daylight saving time (summer
time). As a result, if the automatic DST/
summer time adjustment is set and the alarm is
set at a time skipped when the daylight saving
time begins, the alarm is skipped; if the alarm is
set at a time overlapping when daylight saving
time ends, the alarm will sound twice.

If the same alarm time is set for both ALARM
A and B, the ALARM A takes priority.
To doze for a few more minutes
Press SNOOZE/DATE/SLEEP OFF.
The alarm sound stops but will automatically
come on again after about 10 minutes. Each time
you press SNOOZE/DATE/SLEEP OFF, the
snooze time changes as follows:
The maximum snooze time is 60 minutes.
The display shows the snooze time for about
4 seconds and returns to show the current time.
When you press SNOOZE/DATE/SLEEP OFF
after the current time appears, the snooze time
starts from 10 minutes again.
To stop the Alarm
Press RADIO OFF/ALARM RESET to turn off the
alarm.
The alarm will come on again at the same time
the next day.
If RADIO OFF/ALARM RESET is not pressed, the
alarm sounds continuously for about 60 minutes,
and then it will stop automatically.
To deactivate the Alarm
Set ALARM A (or B) to OFF.
The ALARM A (or B) indicator disappears from
the display.
Note on alarm in the event of a power
interruption
In the event of a power interruption, the alarm
functions work until the battery is empty.
However, the following functions differ:

Nothing will appear on the display.

When the alarm sound is set to radio, it will
change to buzzer automatically.

If the power returns while the alarm sounds,
the alarm sounds continuously for about 60
minutes (or until turned off).
4-135-644-21(1)
©2009 Sony Corporation Printed in China

FM/AM

CLOCK RADIO

ICF-C414

Operating Instructions

Mode d’emploi (au dos)


The alarm buzzes for about one minute, stops
temporarily, and will buzz again after about five
minutes if neither SNOOZE/DATE/SLEEP OFF
or RADIO OFF/ALARM RESET are pressed
while the alarm is buzzing.
If the alarm buzzes and stops (either
automatically after 1 minute or by pressing
SNOOZE/DATE/SLEEP OFF) five times, the
alarm is automatically reset in the case of a
power interruption. The alarm will buzz for 30
minutes (or until turned off) after power is
resumed if the power is resumed within 60
minutes from the alarm time.
If you press SNOOZE/DATE/SLEEP OFF while
the alarm sounds, the snooze time is set to 10
minutes. During a power interruption, snooze
time cannot be set to more than 10 minutes.
If the “
” indicator appears in the display, the
alarm will not work in the event of a power
interruption. Replace the battery if the “
indicator appears.
Setting the sleep timer
You can fall asleep to the radio using the built-in
sleep timer that turns off the radio automatically
after a preset duration.
Press SLEEP.
The radio turns on. You can set the sleep timer to
90, 60, 30, or 15 minutes. Each press changes the
display as follows:
90 60 30 15
OFF
Two short beeps sound when the display returns
to “90”.
The radio will play for the duration you set, then
shut off.
To turn off the radio before the preset
time
Press RADIO OFF/ALARM RESET or SNOOZE/
DATE/SLEEP OFF.
To use both sleep timer and alarm
You can fall asleep to the radio and also be
awakened by the buzzer, radio or melody alarm at
the preset time.
1 Set the alarm. (See “Setting the alarm”.) 2 Set the sleep timer. (See “Setting the sleep timer”.)
Precautions

Play the unit on the power source specified in
“Specifications.

To disconnect the AC power cord (mains lead),
pull it out by the plug, not the cord.

The unit is not disconnected from the AC
power source (mains) as long as it is connected
to the wall outlet, even if the unit itself has been
turned off.

The nameplate and important information
concerning safety are located on the bottom
exterior.

Do not leave the unit in a location near a heat
source such as a radiator or airduct, or in a
place subject to direct sunlight, excessive dust,
mechanical vibration, or shock.

Allow adequate air circulation to prevent
internal heat build-up. Do not place the unit on
a surface (a rug, a blanket, etc.) or near
materials (a curtain) which might block the
ventilation holes.

Should any solid object or liquid fall into the
unit, unplug the unit and have it checked by
qualified personnel before operating it any
further.

To clean the casing, use a soft cloth dampened
with a mild detergent solution.
NOTES ON LITHIUM BATTERY

Wipe the battery with a dry cloth to assure a
good contact.

Be sure to observe the correct polarity when
installing the battery.

Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
If you have any questions or problems concerning
your unit, please consult your nearest Sony dealer.
Troubleshooting
Should any problem occur with the unit, make
the following simple checks to determine whether
or not servicing is required.
If the problem persists, consult your nearest Sony
dealer.
The clock flashes AM 12:00”.

A power interruption occurred and the backup
battery is low. Replace the battery. Remove the
old battery and install a new one.
The buzzer, radio or melody alarm does not
sound at the preset alarm time.

Check that the buzzer, radio or melody alarm is
activated (the ALARM A (or B) indicator lights
up).
The radio alarm is activated but does not
sound at the preset alarm time.

Check that the volume is not set to minimum.
When daylight saving time begins, the clock
does not employ the daylight saving time
automatically.

Make sure the clock is set correctly.

Press and hold DST for at least 3 seconds to
activate the automatic DST/summer time
adjustment.
Specifications
Time display
12-hour System
Frequency range
Band Frequency
FM 87.5 – 108 MHz
AM 530 – 1 710 kHz
Speaker
Approx. 6.6 cm (2
5
/8 inches) dia., 8 Ω
Power output
180 mW (at 10% harmonic distortion)
Power requirements
120 V AC, 60 Hz
For power backup: 3 V DC, one CR2032 battery
Dimensions
Approx. 178.9 × 121.8 × 88.5 mm (w/h/d)
(7
1
/8 × 4
7
/8 × 3
1
/2 inches) incl. projecting parts
and controls
Mass
Approx. 638 g (1 lb 6.5 oz) incl. CR2032 battery
Design and specifications are subject to change
without notice.
Dream Machine is a trademark of Sony Corporation.
Dream Machine est une marque de fabrique de Sony Corporation.
No Power No Problem is a trademark of Sony Corporation.
No Power No Problem est une marque de fabrique de Sony
Corporation.
Battery compartment
AC power cord
There is a tactile dot
above the VOLUME dial to
indicate which way turns
the volume up.
  
s

View the manual for the Sony ICF-C414 here, for free. This manual comes under the category Clock Radio and has been rated by 5 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the Sony ICF-C414 or do you need help? Ask your question here

Need help?

Do you have a question about the Sony and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Sony owners to provide you with a good answer.

Michael Essex • 23-1-2022No comments

Why does my CF414 keep gaining time - adds ~ 1 minute per month+-?

Answer this question

Number of questions: 1

No need to buy external speakers for great audio.  With integrated speakers this display is ready to go once you’re conn...
General
Sony
ICF-C414 | ICFC414S
Clock Radio
4905524556254
English
User manual (PDF)
Radio
Preset stations quantity0
Tuner typeDigital
Radio typeClock
FM band range87.5 - 108 MHz
AM band range530 - 1710 kHz
Loudspeakers
Number of built-in speakers1
Driver unit66 mm
Built-in speaker(s)
Display
Display typeLED
Display diagonal1.4 "
Backlight colourGreen
Backlight
Clock
Integrated clock
Sleep timer
Snooze function
Features
Product colourSilver
Battery
Battery typeCR2032
Weight & dimensions
Weight651 g
Other features
Dimensions (WxDxH)178.9 x 88.5 x 121.8 mm
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Sony ICF-C414 below.

Is your question not listed? Ask your question here

No results