Smeg PV163S2 manual

Smeg PV163S2
6.8 · 1
PDF manual
 · 22 pages
English
manualSmeg PV163S2

Installation

46

5.7 Electrical connection

General information
Check the grid characteristics against the
data indicated on the plate.
The identification plate bearing the
technical data, serial number and brand
name is visibly positioned on the appliance.
Do not remove this plate for any reason.
Perform the ground connection using a wire
that is 20 mm longer than the other wires.
The appliance can work in the following
modes:
220-240 V 1N~
3 x 1 mm² three-core cable.
Fixed connection
Fit the power line with an omnipolar circuit
breaker in compliance with installation
regulations.
The circuit breaker should be located near
the appliance and in an easily reachable
position.
Connection with plug and socket
Make sure that the plug and socket are of
the same type.
Avoid using adapters and shunts as these
could cause overheating and a risk of
burns.
Power voltage
Danger of electrocution
• Have the electrical connection
performed by authorised technical
personnel.
• Use personal protective equipment.
• The appliance must be connected to
earth in compliance with electrical
system safety standards.
• Disconnect the main power supply.
• Do not pull the cable to remove the
plug.
• Use cables withstanding a temperature
of at least 90°C.
• The tightening torque of the screws of
the terminal supply wires must be 1.5 - 2
Nm.
The values indicated above refer
to the cross-section of the internal
conductor.

220-240V~

1 mm
2
20 mm

Manual

View the manual for the Smeg PV163S2 here, for free. This manual comes under the category stoves and has been rated by 1 people with an average of a 6.8. This manual is available in the following languages: English. Do you have a question about the Smeg PV163S2 or do you need help? Ask your question here

Need help?

Do you have a question about the Smeg and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Smeg PV163S2 specifications

Below you will find the product specifications and the manual specifications of the Smeg PV163S2.

General
BrandSmeg
ModelPV163S2 | PV163S2
Productstove
EAN8017709254728
LanguageEnglish
FiletypeUser manual (PDF), Product Brochure (PDF), Brochure (PDF), Warranty information (PDF), Datasheet (PDF)
Design
Appliance placementBuilt-in
Hob typeGas
Number of cooking zones3 zone(s)
Top surface typeGlass
Number of simultaneously used cooking zones3
Product colorBrushed steel
Number of gas cooking zones3 zone(s)
Number of electric cooking zones0 zone(s)
Pan support materialCast iron
Simmer cooking zone shapeRound
Regular cooking zone shapeRound
Large cooking zone shapeRound
Cooking zone 3 power1100 W
Cooking zone 2 shapeRound
Cooking zone 1 power3200 W
Cooking zone 2 positionRight rear
Cooking zone 3 power sourceGas
Cooking zone 3 positionRight front
Cooking zone 2 power sourceGas
Cooking zone 3 shapeRound
Cooking zone 2 power2600 W
Cooking zone 1 positionLeft
Cooking zone 1 shapeRound
Cooking zone 1 typeLarge
Cooking zone 3 typeSimmer
Cooking zone 1 power sourceGas
Cooking zone 2 typeRegular
Power
Connected load (electric)1 W
Connected load (gas)6900 W
AC input voltage220-240 V
AC input frequency50 - 60 Hz
Gas typeLiquefied Petroleum Gas (LPG)
Performance
Simmer cooking zone1100 W
Regular cooking zone2600 W
Large cooking zone3200 W
Thermocouple protectionYes
Ergonomics
Easy to cleanYes
Built-in displayNo
Electronic ignitionYes
Control typeRotary
Control positionTop front
Weight & dimensions
Width600 mm
Depth510 mm
Height48 mm
Installation compartment width560 mm
Installation compartment depth (min)482 mm
Installation compartment depth (max)486 mm
Installation compartment height40 mm
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Smeg PV163S2 below.

Can I use my pans on induction?

Nowadays almost all pans are suitable for induction. You can easily test whether your old pans can also be used on induction by holding a magnet against the bottom of the pan. If the magnet stays on the pan, your old pan is suitable for induction.

How do I reset my induction hob?

Most induction hobs can be reset by disconnecting the hob from power by unplugging it from the power outlet. You will then have to wait at least 60 minutes.

What is a Perilex connection?

A Perilex connection is a special connection that can handle more power than a normal connection. This connection has five holes instead of two and is often used for induction hobs.

Is cooking on induction dangerous?

No, cooking on induction is not dangerous.

What is the height of the Smeg PV163S2?

The Smeg PV163S2 has a height of 48 mm.

What is the width of the Smeg PV163S2?

The Smeg PV163S2 has a width of 600 mm.

What is the depth of the Smeg PV163S2?

The Smeg PV163S2 has a depth of 510 mm.

Is the manual of the Smeg PV163S2 available in English?

Yes, the manual of the Smeg PV163S2 is available in English .

Is your question not listed? Ask your question here

No results