Skandika 500 manual

Skandika 500
5.6 · 1
PDF manual
 · 36 pages
English
manualSkandika 500

View the manual for the Skandika 500 here, for free. This manual comes under the category vibration plates and has been rated by 1 people with an average of a 5.6. This manual is available in the following languages: English. Do you have a question about the Skandika 500 or do you need help? Ask your question here

Need help?

Do you have a question about the Skandika and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandSkandika
Model500
Productvibration plate
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Skandika 500 below.

How can I troubleshoot issues with the console of the Skandika 500 vibration plate?

To troubleshoot issues with the console of the Skandika 500 vibration plate, follow these steps: 1. Check the power connection to ensure the machine is receiving power. 2. Verify that the console is securely connected to the vibration plate. 3. Press the ON/OFF button to restart the machine. 4. Adjust the time and speed using the TIME/SPEED (+) and TIME/SPEED (-) buttons. 5. Switch between the strong and soft modes to see if the issue persists. 6. Check the remote control receiver (RC Receiver) for any obstructions. 7. Monitor the display for any error messages or unusual readings. 8. If the issue persists, refer to the manual for further troubleshooting steps.

What should I do if the remote control of the Skandika 500 vibration plate is not functioning properly?

To troubleshoot the remote control of the Skandika 500 vibration plate if it's not functioning properly, follow these steps: 1. Check the batteries in the remote control and replace them if necessary. 2. Ensure there are no obstructions blocking the signal between the remote control and the receiver on the vibration plate. 3. Try resetting the remote control by removing the batteries, pressing all the buttons to discharge any remaining power, and then reinserting the batteries. 4. Make sure the remote control is within a reasonable range from the vibration plate for proper functionality. 5. If the issue persists, consider contacting customer support for further assistance.

How can I troubleshoot operational issues with the Skandika 500 vibration plate?

To troubleshoot operational issues with the Skandika 500 vibration plate, follow these steps: 1. Press the ON/OFF button to start up the machine and press it again to turn it off. 2. Adjust the time by pressing the TIME (+) button to increase the time and the TIME (-) button to reduce it. 3. Adjust the speed by pressing the SPEED (+) button to increase the speed and the SPEED (-) button to decrease it. 4. For mode selection, press the mode button to switch between manual program ("00") and automatic programs ("P1, P2, P3"). 5. To switch between soft mode and powerful mode, press the SWITCH button accordingly.

How do I select and switch between the Manual and Automatic Program (P1, P2, P3) on the Skandika 500 vibration plate?

To select and switch between the Manual and Automatic Program (P1, P2, P3) on the Skandika 500 vibration plate, follow these steps: 1. Press the MODE button on the console. 2. Use the same button to toggle between Manual and Automatic Program options. 3. Select the desired program (P1, P2, or P3) by pressing the MODE button until the correct program is displayed. 4. Confirm your selection by pressing the corresponding button for the chosen program. 5. To switch between the Manual and Automatic Program, repeat the process by pressing the MODE button and selecting the desired program. These steps will allow you to easily switch between the Manual and Automatic Program options on your Skandika 500 vibration plate.

What should I do if the selected Manual Program (P1, P2, P3) is not running as expected?

If the selected Manual Program (P1, P2, P3) is not running as expected on the Skandika 500 vibration plate, follow these steps: 1. Check the TIME/SPEED buttons to ensure the correct settings for time and speed. 2. Verify that the machine is turned on using the ON/OFF button. 3. Use the MODE button to select the desired manual program (P1, P2, P3). 4. If the issue persists, switch between the strong and soft modes using the SWITCH button. 5. Monitor the TIME and SPEED/MODE displays for any anomalies in the settings. 6. If the problem continues, consider using the remote control receiver (RC Receiver) for troubleshooting. 7. Ensure that the vibration plate is in the appropriate mode (STRONG or SOFT) based on your preference. These steps should help resolve any issues with the selected Manual Program on the Skandika 500 vibration plate.

Is the manual of the Skandika 500 available in English?

Yes, the manual of the Skandika 500 is available in English .

Is your question not listed? Ask your question here

No results