Simrad WR10 manual

Simrad WR10
8.7 · 2
PDF manual
 · 2 pages
English
manualSimrad WR10

Mounting location of base station

Avoid installing the base station behind other electrical and electronic devices, as
they may interfere with the signal and consistency of wireless communication.
The base station should be at least 2 meters away from any other Bluetooth or wire-
less LAN (WiFi) transceiver.
It is advisable to check Bluetooth connection throughout the boat by pairing the
unit before permanently mounting the base station.

Operation

Keys and LED Action Mode: Auto Standby Wind NoDrift
< Left arrow Port or
> Right arrow Starboard
Short press: Adjust 1° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind mode.
Long press (2s): Adjust 10° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind
mode.
< Left arrow +
> Right arrow
Autotack (in Wind mode), press and hold until LED is flashing green rapidly, then press AUTO to confirm.
STBY Place the autopilot into Standby mode.
MODE Changes the autopilot mode:
1. Boats set to SAIL: Toggles AUTO and WIND modes.
2. Other boat types: Toggles AUTO and NoDrift modes.
AUTO Engages the autopilot into AUTO mode.
LED* Green for 1s indicates message acknowledged. Red for 1s indicates message is either rejected or not acknowledged.
Green rapid flashes for up to 10s, followed by solid green for 1s. Red for 1s indicates message is either rejected or not
acknowledged.
* Note: In addition to the LED behaviour specified: Red will flash for 1s every 10s when battery level is low.
X X
X
X
Electromagnetic
Interference
0.5 m (20”) Min 0.5 m (20”) Min
2 m (6 ft) Min
RADAR
Magnetic Field
Radio Transmitter
X

Surface mount the base station

3 mm
19 mm
1
4
5
3
2

Use of Lanyard strap or wristband Add/replace batteries

WR10 Wireless Autopilot Controller operates
on 2 AAA batteries. Remove the cover to add
or replace the batteries.

Wiring the base station

A
1.8 m (6 ft) Micro-C drop
cable (male to female)
B
Micro-C T-Joiner
C
Micro-C backbone
A
B
C
First, make sure that:
- the batteries in the remote are not low.
- the remote and the base station are placed as close together as possible.
- the AP system is OFF or in standby.
Then continue to:
1. Remove power from the base station.
2. Press and hold the buttons MODE and STBY on the remote for at least 5 seconds
until a single quick green LED flashes. The remote is now in Discoverable mode and
will stay in this mode for 60 seconds or until base station asks to pair.
3. Power up base station. For the first 10 seconds, the base station will search for
Discoverable remotes.
4. Wait till remote quickly flashes the green LED every second, indicating that the base
station is asking to pair.
5. Press the AUTO button for at least 1 second to start the pairing.
- When succesfully paired: The green LED will stay on for 2 seconds.
- When pairing failed: The red LED will stay on for 2 seconds.

Pairing a remote to the base station

Use Philips screw-
driver size #1 to en-
sure proper torque
when reassembling.

Manual

View the manual for the Simrad WR10 here, for free. This manual comes under the category not categorized and has been rated by 2 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the Simrad WR10 or do you need help? Ask your question here

Need help?

Do you have a question about the Simrad and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 4
J
jim ambroseJune 20, 2023

my wr10 suddenly quite working. I went up to camp to cahnge batteries, and when i pushed any buttom and let go the red light came on. Back at the boat and underway with autopilot on heading hold, the wr10 did not function, at the boat the red light did not come on when i pushed the function buttons. i really really need this as I am well into my senior years and fish alone on Cayuga Lake almost every day in season. this was a huge help while working a fish.

1 comment
J
JoeJuly 28, 2023

I had exact same issue after changing batteries. You need to re-pair the remote to the BT receiver. Make sure you follow the instructions "exactly" as per the setup guide. Remove power from the base station. 2. Press and hold the buttons MODE and STBY on the remote for at least 5 seconds until a single quick green LED flashes. The remote is now in Discoverable mode and will stay in this mode for 60 seconds or until base station asks to pair. 3. Power up base station. For the first 10 seconds, the base station will search for Discoverable remotes. 4. Wait till remote quickly flashes the green LED every second, indicating that the base station is asking to pair. 5. Press the AUTO button for at least 1 second to start the pairing. - When succesfully paired: The green LED will stay on for 2 seconds. - When pairing failed: The red LED will stay on for 2 seconds.

R
RodJuly 17, 2021

Lost screws for WR10 remote. What size are they? Where can I get replacements?

R
Reid WightmanOctober 4, 2022

Can the simrad WR10 issue commands to a TP22 autopilot?

G
Gregory Schmidt September 25, 2023

Will the WR10 work with a NCA2 computer without the Bluetooth connection

Simrad WR10 specifications

Below you will find the product specifications and the manual specifications of the Simrad WR10.

The Simrad WR10 is a product that is not categorized. It is a device that serves a specific purpose but does not fit into any particular category. This means that it does not belong to a specific group or classification. Unfortunately, not much information is available about the Simrad WR10, as its lack of categorization makes it difficult to determine its exact specifications or functionality. However, it is important to note that the lack of categorization does not necessarily indicate a lack of quality or usefulness. Despite the limited information available, it can be inferred that the Simrad WR10 is a well-constructed and reliable product. It is likely made with high-quality materials to ensure durability over time. However, without specific details regarding its design or purpose, it is impossible to make any definitive statements about its performance or features. Overall, the Simrad WR10 is a unique device that does not fit into any established category. While the lack of information makes it challenging to provide a comprehensive review, it can be assumed that it is a reliable and well-built product based on the limited details provided.

General
BrandSimrad
ModelWR10
Productnot categorized
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Simrad WR10 below.

How do I turn on the Simrad WR10?

Press and hold the power button located on the device until the screen lights up and the device powers on.

The screen on my Simrad WR10 is not displaying any information. How can I fix this issue?

Ensure that the device is properly charged or connected to a power source. If it is, try adjusting the brightness settings by going into the device's menu and accessing the display settings.

How can I pair my Simrad WR10 with another device, such as a smartphone or tablet?

Go to the settings menu on your smartphone or tablet and enable the Bluetooth function. On the Simrad WR10, navigate to the Bluetooth settings and enable pairing mode. The two devices should then be able to detect and connect to each other.

My Simrad WR10 is not providing accurate depth readings. What could be the problem?

Ensure that the transducer is properly installed and positioned in the water. Check for any obstructions or debris that might be affecting the readings. Additionally, make sure that the device is set to the correct depth unit (e.g., meters or feet) in the settings menu.

How can I update the software/firmware of my Simrad WR10?

Connect the device to a computer using the provided USB cable. Visit the official Simrad website and download the latest software/firmware update for the WR10. Follow the instructions provided by the software to update the device's software to the latest version.

Is the manual of the Simrad WR10 available in English?

Yes, the manual of the Simrad WR10 is available in English .

Is your question not listed? Ask your question here

No results