Silva 56013 manual

Silva 56013
7.4 · 1
PDF manual
 · 1 page
English
manualSilva 56013
Wir gratulieren Ihnen zum Kauf eines SILVA Schrittzählers/Pedometers!
Ein Schrittzähler/Pedometer ist ein Gerät, das je nach dem gewählten Moell die
Anzahl der Schritte, Entfernungen, tatsächliche Trainingszeit und verbrauchte
Kalorien anzeigt.
Bewegung fördert Ihre Gesundheit und ein gesundes Leben mit einem
Schrittzähler/Pedometer macht der Spaziergang/das Lauftraining noch mehr

Spaß!

Allgemeines über Pedometer
Um jeden Schritt erfassen zu können, arbeitet das Pedometer mit einem eingebauten Pendel.
Das Pendel ist beweglich und erzeugt bei jeder Bewegung ein klickendes Geräusch. Das ist
normal und eine Voraussetzung für das Funktionieren des Pedometers.
Befestigung des Pedometers
Befestigen Sie das Pedometer am besten am Hosenbund oder an einem Gürtel an der Hüfte.
Um eine optimale Funktion des Geräts zu gewährleisten, muss das Pedometer aufrecht
positioniert werden, d.h. ohne Neigung.
Batteriewechsel
Wenn die Displayanzeige schwach zu werden beginnt, müssen die Batterien gewechselt
werden. Lösen Sie die Schrauben auf der Rückseite mit einem Sternschraubenzieher.
Wechseln Sie die Batterie (Typ L1142). Lebensdauer der Batterie: ca. 1 Jahr.
Sonstiges
Das Pedometer ist weder wasserdicht noch stoßsicher behandeln Sie es deshalb sorgsam.
Garantie
1 Jahr Garantie für Fabrikationsmängel. Die Garantie erstreckt sich nicht auf normalen
Verschleiß oder Schäden, die durch Unachtsamkeit oder Veränderungen welcher Art auch
immer entstanden sind. Die Garantie gilt nicht für die Batterie.
Anweisung für Modell STEP COUNTER
(Silber/Rot) Art.Nr. 56012
Dieses Modell wurde für die Berechnung der Schrittanzahl
entwickelt.
Nullstellung des Schrittzählers
Eine der Tasten drücken und eine Sekunde gedrückt halten.
Der Schrittzähler wird auf Null gestellt.
Anweisungen für Modell PEDOMETER
(Silber/Blau) Art.Nr. 56013
Dieses Modell wurde für die Berechnung der Schrittanzahl
entwickelt und zeigt außerdem die zurückgelegte Entfernung
an. Um die Entfernung anzeigen zu können, muss die
Schrittlänge eingestellt werden.
Einstellung der Schrittlänge
Die Schrittlänge ermitteln Sie am einfachsten dadurch, dass Sie zum Beispiel 10 Schritte gehen
und die zurückgelegte Entfernung messen. Wenn Sie die Entfernung durch 10 dividieren,
erhalten Sie die aktuelle Schrittlänge.
Auf MODE drücken, so dass der Text „KM“ im Display erscheint.
Dann auf STRIDE drücken. Die eingestellte Schrittlänge beginnt zu blinken. Wiederholt auf
STRIDE drücken, um die Schrittlänge auf den gewünschten Wert zu erhöhen (die Schrittlänge
wird pro Tastendruck um 1 cm erhöht; wenn MIL eingestellt ist, um 0,1 ft.). STRIDE loslassen.
Nach einigen Sekunden kehrt der Schrittzähler zur Entfernungsfunktion zurück und die neue
Schrittlänge ist eingestellt.
Anzeige der Schrittanzahl
Auf MODE drücken, bis der Text „STEP“ im Display erscheint.
Anzeige der zurückgelegten Entfernung
Auf MODE drücken, so dass der Text „KM“ (oder MIL, wenn Meilen als Einheit gewählt
wurden) im Display erscheint.
Nullstellung des Schrittzählers
Die Tasten MODE und STRIDE drücken und eine Sekunde gedrückt halten, um den
Schrittzähler auf Null zu stellen.
Änderung der Entfernungseinheit
Die Grundeinstellung des Pedometers lautet auf km (und cm für die Schrittlänge). Diese
Einstellung kann in Miles/ft geändert werden.
MODE und STRIDE gleichzeitig drücken und länger als 5 Sekunden gedrückt halten. Das
Display zeigt nun MIL statt KM an. Um wieder zurückzuwechseln, den Vorgang wiederholen.
Filterfunktion
Das Pedometer ist mit einer Funktion ausgestattet, die eine unbeabsichtigte Erfassung von
Schritten verhindert, wenn Sie stehen oder kurze zufällige Bewegungen machen, die nicht
zu Ihrem Spaziergang/Lauftraining gehören. Für die Schrittzählung müssen 6 Schritte ohne
Unterbrechung gemacht werden.
Anweisungen für Modell PEDOMETER
PLUS (Silber/Grau) Art.Nr. 56014
Dieses Modell wurde für die Berechnung der Schrittanzahl,
der zurückgelegten Entfernung und der verbrauchten Kalorien
entwickelt und ist außerdem mit einem Timer ausgestattet.
Um die Entfernung anzeigen und den Kalorienverbrauch
berechnen zu können, müssen die Schrittlänge und das
Körpergewicht eingegeben werden.
Einstellung der Schrittlänge
Die Schrittlänge ermitteln Sie am einfachsten dadurch, dass Sie zum Beispiel 10 Schritte gehen
und die zurückgelegte Entfernung messen. Wenn Sie die Entfernung durch 10 dividieren,
erhalten Sie die aktuelle Schrittlänge.
Auf MODE drücken, so dass der Text „KM“ im Display erscheint.
Dann auf SET drücken. Die eingestellte Schrittlänge beginnt zu blinken. Wiederholt auf SET
drücken, um die Schrittlänge auf den gewünschten Wert zu erhöhen (die Schrittlänge wird pro
Tastendruck um 1 cm erhöht; wenn MIL eingestellt ist, um 0,1 ft.). SET loslassen. Nach einigen
Sekunden kehrt der Schrittzähler zur Entfernungsfunktion zurück und die neue Schrittlänge ist
eingestellt.
Einstellung des Körpergewichts
Wiederholt auf MODE drücken, bis CAL im Display erscheint.
Dann auf SET drücken. Das eingestellte Körpergewicht beginnt zu blinken. Wiederholt auf SET
drücken, um das Körpergewicht auf den gewünschten Wert zu erhöhen (das Körpergewicht
wird pro Tastendruck um 5 kg erhöht; wenn MIL eingestellt ist, um 10 lb). SET loslassen.
Nach einigen Sekunden kehrt der Schrittzähler zur Kalorienfunktion zurück und das neue
Körpergewicht ist eingestellt.
Anzeige der Schrittanzahl
Auf MODE drücken, bis der Text „STEP“ im Display erscheint.
Anzeige der zurückgelegten Entfernung
Auf MODE drücken, so dass der Text „KM“ (oder MIL, wenn Meilen als Einheit gewählt
wurden) im Display erscheint.
Anzeige der verbrauchten Kalorien
Auf MODE drücken, bis der Text „CALim Display erscheint.
Anzeige der tatsächlichen Geh-/Trainingszeit
Auf MODE drücken, bis der Text TMR“ im Display erscheint.
Der eingebaute Timer funktioniert automatisch. Er schaltet sich ein, wenn Sie mit Ihrem
Spaziergang/Lauftraining beginnen und schaltet sich aus, wenn Sie stehen bleiben.
Nullstellung des Schrittzählers
Die Tasten MODE und SET drücken und eine Sekunde gedrückt halten, um den Schrittzähler
auf Null zu stellen.
Änderung der Entfernungs- und Gewichtseinheit
Die Grundeinstellung des Pedometers lautet auf km (und cm für die Schrittlänge) sowie auf kg
für das Körpergewicht. Diese Einstellung kann in Miles/ft bzw. lb geändert werden.
MODE und SET gleichzeitig drücken und länger als 5 Sekunden gedrückt halten. Das Display
zeigt nun MIL statt KM und bei der Einstellung des Körpergewichts lb statt kg an. Um wieder
zurückzuwechseln, den Vorgang wiederholen.
Filterfunktion
Das Pedometer Plus ist mit einer Funktion ausgestattet, die eine unbeabsichtigte Erfassung
von Schritten verhindert, wenn Sie stehen oder kurze zufällige Bewegungen machen, die nicht
zu Ihrem Spaziergang/Lauftraining gehören. Für die Schrittzählung müssen 6 Schritte ohne
Unterbrechung gemacht werden.

Congratulations on your purchase of a SILVA Pedometer/Step Counter!

A Step Counter/Pedometer is an exercise device which, depending on model,

counts number of steps, and calculates distance, exercise time and consumed

calories.

Exercising is good for your health and with a Step Counter/Pedometer your walk

or jog will be even more fun!

General about Pedometers
To register every step the pedometer uses a built-in pendulum. This pendulum is moving and
will during movement give a clicking sound. This is completely normal and is required to make
the product work properly.
Attaching the Pedometer
The ideal place is to attach it on the top of the trousers or on a belt close to the hip. For best
functionality it shall be place vertically i.e. not tilting.
Battery change
Change battery when the display dims. Use a screwdriver to open the rear case.
Change battery (type L1142). Battery life is approx.1 year.
Misc
The Pedometer is not shock-, or waterproof – therefore treat it carefully.
Warranty
1 year warranty against manufacturing faults. The warranty does not apply to modications,
normal wear and tear or abuse. Battery is not covered by this warranty.

Instruction for model STEP COUNTER

(Silver/Red) Art.no. 56012

This model is developed to count the number of steps taken.
Reset the Step Counter
Press and hold any of the two buttons for a second and the
counter is reset.

Instruction for model PEDOMETER

(Silver/Blue) Art.nr. 56013

This model is developed to count the number of steps taken
and to show distance. To be able to show distance the stride
length has to be entered.
Set the stride length
The easiest way to nd the stride length is to walk for
example 10 steps and then measure that distance. Divide the distance by 10 to nd the stride
length.
Press MODE so the text KM appears in the display.
Press STRIDE and the current stride length starts ashing. Press STRIDE repeatedly to
increase the stride length to the wished value (increases by 1 cm per press, or 0.1 ft if MIL is
selected) and then release STRIDE. After a few seconds the Step Counter will return to the
distance function and the new stride length is set.
Show number of steps
Press MODE until the text “STEP” is shown in the display.
Show distance
Press MODE until the text ”KM” (or MIL if miles is selected) is shown in the display.
Reset the Pedometer
Press and hold MODE and STRIDE buttons simultaneously for a second and the counter is
reset.
Change of distance unit
The Pedometers default setting is km (and cm for stride length). This can be changed to miles/
ft:
Press and hold MODE and STRIDE buttons simultaneously for 5 seconds. The display will now
show MIL instead of KM. Repeat to change back.
Filter function
The Pedometer has a function, which prevents accidental registration of steps when standing
still or at short accidental movements that is not part of the walk/jog. For correct step counting
6 steps in a row must be taken without a stop.

Instruction for model PEDOMETER PLUS

(Silver/Grey) Art.nr. 56014

This model is developed to count the number of steps taken,
show distance, calculate consumed calories and take the
effective time. To be able to show distance and calculate
calories the stride length and body weight has to be entered.
Set the stride length
The easiest way to nd the stride length is to walk for example 10 steps and then measure that
distance. Divide the distance by 10 to nd the stride length.
Press MODE so the text KM appears in the display.
Press SET and the current stride length starts ashing. Press SET repeatedly to increase the
stride length to the wished value (increases by 1 cm per press, or 0.1 ft if MIL is selected) and
then release SET. After a few seconds the Pedometer Plus will return to the distance function
and the new stride length is set.
Set the body weight
Press MODE repeatedly until CAL is shown in the display.
Now press SET and the current body weight starts ashing.
Press SET repeatedly to increase the body weight to the wished value (increases by 5 kg per
press, or 10 lb if MIL is selected) and then release SET. After a few seconds the Pedometer
Plus will return to the calorie function and the new body weight is set.
Show number of steps
Press MODE until the text “STEP” is shown in the display.
Show distance
Press MODE until the text “KM” (or MIL if miles is selected) is shown in the display.
Show consumed calories
Press MODE until the text “CAL” is shown in the display.
Show effective time of the walk/jog
Press MODE until the text “TMR” is shown in the display.
The timer is automatic and starts when starting walking/jogging and stops when stopping.
Reset the Pedometer
Press and hold MODE and SET buttons simultaneously for a second and the counter is reset.
Change of distance-, and weight unit
The Pedometer Plus default setting is km (and cm for stride length). This can be changed to
miles/ft and lb:
Press and hold MODE and SET buttons simultaneously for 5 seconds. The display will now
show MIL instead of KM and lb instead of kg in the body weight setting. Repeat to change
back.
Filter function
The Pedometer Plus has a function, which prevents accidental registration of steps when
standing still or at short accidental movements that is not part of the walk/jog. For correct step
counting 6 steps in a row must be taken without a stop.

Grattis till Ditt köp av en SILVA Stegräknare/Pedometer!

En stegräknare/pedometer är ett motionstillbehör som, beroende av vald modell,

håller ordning på antal steg, distans, effektiv motionstid samt förbrukade kalorier.

Att motionera främjar god hälsa och ett sunt liv – med en Stegräknare/Pedometer

blir promenaden/löpturen ännu roligare!

Allmänt om pedometrar
För att registrera varje steg använder pedometern en inbyggd pendel. Pendeln är rörlig och
kommer vid rörelse att avge ett klickande ljud. Detta är normalt och är en förutsättning för att
pedometern skall fungera.
Placering av pedometern
Idealiska placeringen är i byxlinning eller livrem vid höften. För bästa funktion skall pedometern
fästas helt upprätt d.v.s. inte luta.
Batteribyte
Byt batteri när displayens tecken börjar bli svaga. Använd stjärnskruvmejsel och lossa skruvarna
på baksidan. Byt batteri (typ L1142). Batterilivslängd ca 1 år.
Övrigt
Pedometern är inte vattentät eller stötskyddad – behandla den därför varsamt.
Garanti
1 års garanti mot fabrikationsfel. Garantin omfattar inte normal förslitning, skador uppkomna
genom oaktsamhet samt om pedometern på något sätt modierats. Batteriet omfattas ej av
garantin.

Instruktion för modell STEP COUNTER

(Silver/Röd) Art.nr. 56012

Denna modell är framtagen för att räkna antalet steg.
Nollställning av stegräknaren
Tryck och håll in någon av knapparna under en sekund så
nollställs stegräknaren.

Instruktion för modell PEDOMETER

(Silver/Blå) Art.nr. 56013

Denna modell är framtagen för att räkna antalet steg och
även visa tillryggalagd distans. För att kunna visa distans
måste inställning av steglängd ske.
Inställning av steglängd
Att ta reda på steglängden görs enklast genom att
exempelvis gå 10 steg och sedan mäta den tillryggalagda distansen. Dividera distansen med 10
och aktuell steglängd erhålls.
Tryck MODE så att texten KM syns i displayen.
Tryck på STRIDE varvid den inställda steglängden börjar blinka. Tryck upprepade gånger på
STRIDE för att öka steglängden till önskat värde (ökning sker med 1 cm per tryck, eller 0.1
ft om MIL är inställt) och släpp sedan STRIDE. Efter några sekunder återgår stegräknaren till
distansfunktionen och den nya steglängden är inställd.
Visa antal steg
Tryck på MODE tills texten ”STEP” syns i displayen.
Visa tillryggalagd distans
Tryck på MODE tills texten ”KM” (eller MIL om miles valts som enhet) syns i displayen.
Nollställning av stegräknaren
Tryck och håll in MODE och STRIDE knapparna under en sekund så nollställs stegräknaren.
Byte av distansenhet
Pedometerns grundinställning är km (och cm för steglängd). Denna kan ändras till miles/ft:
Tryck och håll inne MODE och STRIDE samtidigt i mer än 5 sekunder. Displayen kommer nu
visa MIL i stället för KM. För att byta tillbaka upprepa förfarandet.
Filterfunktion
Pedometer är försedd med en funktion som förhindrar oavsiktlig stegregistrering vid
stillastående eller vid korta tillfälliga rörelser som inte är en del av promenaden/löpturen. För att
stegräkning skall ske måste 6 steg i rad tas utan uppehåll.

Instruktion för modell PEDOMETER

PLUS (Silver/Grå) Art.nr. 56014

Denna modell är framtagen för att räkna antalet steg, visa
tillryggalagd distans, mäta antalet förbrukade kalorier samt
ta den effektiva tiden. För att kunna visa distans och räkna
ut kaloriförbrukning måste inställning av steglängd och
kroppsvikt ske.
Inställning av steglängd
Att ta reda på steglängden görs enklast genom att exempelvis gå 10 steg och sedan mäta den
tillryggalagda distansen. Dividera distansen med 10 och aktuell steglängd erhålls.
Tryck MODE så att texten KM syns i displayen.
Tryck på SET varvid den inställda steglängden börjar blinka. Tryck upprepade gånger på SET för
att öka steglängden till önskat värde (ökning sker med 1 cm per tryck, eller 0.1 ft om MIL är
inställt) och släpp sedan SET. Efter några sekunder återgår stegräknaren till distansfunktionen
och den nya steglängden är inställd.
Inställning av kroppsvikt
Tryck MODE upprepade gånger tills CAL syns i displayen.
Tryck nu på SET varvid den inställda kroppsvikten börjar blinka. Tryck upprepade gånger på SET
för att ändra kroppsvikten till önskat värde (ökning sker med 5 kg per tryck, eller 10 lb om MIL
är inställt) och släpp sedan SET. Efter några sekunder återgår stegräknaren till kalorifunktionen
och den nya kroppsvikten är inställd.
Visa antal steg
Tryck på MODE tills texten ”STEP” syns i displayen.
Visa tillryggalagd distans
Tryck på MODE tills texten ”KM” (eller MIL om miles valts som enhet) syns i displayen.
Visa förbrukade kalorier
Tryck på MODE tills texten ”CAL” syns i displayen.
Visa effektiv gång/löptid
Tryck på MODE tills texten ”TMR” syns i displayen.
Den inbyggda timern fungerar automatiskt och startar vi påbörjad gång/löpning och stannar vid
uppehåll.
Nollställning av stegräknaren
Tryck och håll in MODE och SET knapparna under en sekund så nollställs stegräknaren.
Byte av distans-, och viktenhet
Pedometerns grundinställning är km (och cm för steglängd) samt kg för kroppsvikt. Denna kan
ändras till miles/ft respektive lb:
Tryck och håll inne MODE och SET samtidigt i mer än 5 sekunder. Displayen kommer nu visa
MIL i stället för KM och vid kroppsviktsinställning lb i stället för kg. För att byta tillbaka upprepa
förfarandet.
Filterfunktion
Pedometer Plus är försedd med en funktion som förhindrar oavsiktlig stegregistrering vid
stillastående eller vid korta tillfälliga rörelser som inte är en del av promenaden/löpturen. För att
stegräkning skall ske måste 6 steg i rad tas utan uppehåll.
Toutes nos félicitations pour l’achat du podomètre/compteur de pas SILVA !
Un podomètre/compteur de pas est un article de sport qui, en fonction du
modèle, permet de compter le nombre de pas effectués, de calculer la distance
parcourue, le temps de course effectif ainsi que la consommation en calories.
Le sport est facteur de bonne santé et de vie saine mais grâce au podomètre/
compteur de pas, la marche ou le jogging n’en auront que plus d’intérêt !
Généralités sur les podomètres
An d’enregistrer chaque pas, le podomètre utilise un pendule intégré. Ce pendule étant
mobile, un clic sonore se fait entendre à chaque mouvement. Ceci est tout à fait normal et
nécessaire au bon fonctionnement du podomètre.
Placement du podomètre
Il se clipe de manière idéale à la ceinture du pantalon ou sur une ceinture portée sur
les hanches. Pour une meilleure fonctionnalité, nous vous recommandons de le placer
verticalement et de ne pas le pencher.
Changement de pile
Changer la pile lorsque les chiffres afchés commencent à s’affaiblir. Utiliser un tournevis et
dévisser les vis à l’arrière. Changer la pile (type L1142). Durée de vie de la pile : environ 1 an.
Autres
Le pédomètre n’est ni étanche ni protégé contre les chocs nous vous recommandons donc
d’en prendre particulièrement soin.
Garantie
1 an de garantie contre les défauts de fabrication. La garantie ne couvre pas l’usure normale,
les dommages résultants d’une négligence ainsi que les éventuelles modications qui
pourraient être faites sur le podomètre. La pile n’est pas couverte par la garantie.
Instruction d’utilisation pour le modèle
STEP COUNTER (Argent/Rouge) art.

56012

Ce modèle est conçu pour le calcul du nombre de pas
effectués.
Réinitialiser le compteur de pas
Maintenir l’un des boutons enfoncé durant une seconde pour
remettre le compteur à zéro.
Instruction d’utilisation pour le modèle
PEDOMETER (Argent/Bleu) art. 56013
Ce modèle est conçu pour le calcul du nombre de pas et de
la distance parcourue. An de pouvoir indiquer la distance, la
longueur du pas doit tout d’abord être programmée.
Programmer la longueur de pas
La manière la plus simple pour cela est de faire par exemple
10 pas, puis de mesurer la distance parcourue. Il suft ensuite de diviser cette distance par 10
pour obtenir la longueur moyenne de votre pas.
Appuyer sur MODE de manière à afcher le texte KM.
Appuyer sur STRIDE et la longueur de pas réglée commence à clignoter. Répéter la pression
sur la touche STRIDE jusqu’à obtenir la longueur souhaitée (une pression augmente la longueur
de 1 cm, ou de 0,1 ft sur MIL) puis relâcher STRIDE. Quelques secondes après, le compteur
revient sur la fonction de calcul de la distance en fonction de la nouvelle longueur de pas.
Indiquer le nombre de pas
Appuyer sur MODE jusqu’à ce que le texte «STEP» s’afche.
Indiquer la distance parcourue
Appuyer sur MODE jusqu’à ce que le texte «KM» (ou MIL si l’unité miles a été sélectionnée)
s’afche.
Réinitialisation du podomètre
Appuyer et maintenir enfoncés les boutons MODE et STRIDE durant une seconde an de
remettre le compteur à zéro.
Changement de l’unité de distance
Le podomètre est réglé par défaut sur l’unité km ( et cm pour la longueur de pas). Il est
possible de passer en unité miles/ft :
Appuyer simultanément sur MODE et STRIDE en les maintenant enfoncés durant plus de
5 secondes. MIL s’afche alors à la place de KM. Pour revenir à l’unité précédente, répéter
l’opération.
Fonction de ltre
Le podomètre est pourvu d’une fonction permettant d’éviter l’enregistrement accidentel de
pas en position immobile ou lors de petits mouvements ne faisant pas partie de la marche
ou du jogging. Le calcul des pas ne se fera que lorsque 6 pas seront effectués d’aflée sans
aucune pose.
Instruction d’utilisation pour le modèle
PEDOMETER PLUS (Argent/Gris) art

56014

Ce modèle est conçu pour le calcul du nombre de pas, de
la distance parcourue, de la consommation en calories ainsi
que de la durée effective. Le calcul de la distance et de la
consommation en calories ne peut se faire que sur la base
de la longueur du pas et du poids programmés.
Programmer la longueur de pas
La manière la plus simple pour cela est de faire par exemple 10 pas, puis de mesurer la
distance parcourue. Il suft ensuite de diviser cette distance par 10 pour obtenir la longueur
moyenne de votre pas.
Appuyer sur MODE de manière à afcher le texte KM.
Appuyer sur SET et la longueur de pas réglée commence à clignoter. Répéter la pression sur la
touche SET jusqu’à obtenir la longueur souhaitée (une pression augmente la longueur de 1 cm,
ou de 0,1 ft sur MIL) puis relâcher SET. Quelques secondes après, le compteur revient sur la
fonction de calcul de la distance en fonction de la nouvelle longueur de pas.
Programmer votre poids
Appuyer plusieurs fois sur MODE jusqu’à ce que CAL s’afche.
Appuyer ensuite sur SET et le poids programmé commence à clignoter. Répéter la pression
sur la touche SET jusqu’à obtenir le poids souhaité (une pression augmente la valeur de 5 kg,
ou de 10 lb sur MIL) puis relâcher SET. Quelques secondes après, le compteur revient sur la
fonction du calcul de la consommation en calories en fonction du nouveau poids programmé.
Indiquer le nombre de pas
Appuyer sur MODE jusqu’à ce que le texte «STEP» s’afche.
Indiquer la distance parcourue
Appuyer sur MODE jusqu’à ce que le texte «KM» (ou MIL si l’unité miles a été sélectionnée)
s’afche.
Indiquer la consommation en calories
Appuyer sur MODE jusqu’à ce que le texte «CAL» s’afche.
Indiquer le temps de marche/course effectif
Appuyer sur MODE jusqu’à ce que le texte «TMR» s’afche.
Le minuteur intégré fonctionne automatiquement et se déclenche dès que la marche/ le
jogging démarre puis s’interrompt dès l’arrêt.
Réinitialisation du podomètre
Appuyer et maintenir enfoncés les boutons MODE et SET durant une seconde an de remettre
le compteur à zéro.
Changement de l’unité de distance et de poids
Le podomètre est réglé par défaut sur l’unité km (et cm pour la longueur de pas) et l’unité kg
pour le poids.
Il est possible de passer en unités miles/ft et lb :
Appuyer simultanément sur MODE et SET en les maintenant enfoncés durant plus de 5
secondes. MIL s’afche alors à la place de KM et lb à la place de kg. Pour revenir aux unités
précédentes, répéter l’opération.
Fonction de ltre
Le podomètre est pourvu d’une fonction permettant d’éviter l’enregistrement accidentel de
pas en position immobile ou lors de petits mouvements ne faisant pas partie de la marche
ou du jogging. Le calcul des pas ne se fera que lorsque 6 pas seront effectués d’aflée sans
aucune pose.

www.silva.se

View the manual for the Silva 56013 here, for free. This manual comes under the category pedometers and has been rated by 1 people with an average of a 7.4. This manual is available in the following languages: English. Do you have a question about the Silva 56013 or do you need help? Ask your question here

Need help?

Do you have a question about the Silva and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandSilva
Model56013
Productpedometer
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Silva 56013 below.

How much should I exercise as an adult per week?

As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.

How do I know when to change the battery in the Silva 56013 pedometer?

To determine when to change the battery in the Silva 56013 pedometer, follow these steps: 1. Observe the display: When the display dims, it is an indication that the battery needs to be changed. 2. Prepare for battery change: Use a screwdriver to open the rear case of the pedometer. 3. Identify the battery type: The Silva 56013 pedometer uses a battery type L1142. 4. Determine battery life: The battery life of the pedometer is approximately 1 year. Remember to handle the pedometer with care as it is not shockproof or waterproof. The warranty does not cover battery replacement or normal wear and tear. Please note that these steps are based on the information provided and may vary slightly depending on the specific model of the Silva 56013 pedometer.

How do I change the battery in the Silva 56013 pedometer?

To change the battery in the Silva 56013 pedometer, follow these steps: 1. Prepare for battery change: Use a screwdriver to open the rear case of the pedometer. 2. Identify the battery type: The Silva 56013 pedometer uses a battery type L1142. 3. Replace the battery: Remove the old battery from the battery compartment and insert a new L1142 battery in the correct orientation. 4. Close the rear case: Align the rear case with the pedometer and securely fasten it using the screwdriver. Please note that the battery life of the Silva 56013 pedometer is approximately 1 year. It is recommended to change the battery when the display dims. Handle the pedometer with care as it is not shockproof or waterproof. These steps should help you successfully change the battery in your Silva 56013 pedometer.

How do I set the stride length on the Silva 56013 pedometer?

To set the stride length on the Silva 56013 pedometer, follow these steps: 1. Press the MODE button until the text "KM" (or "MIL" if miles is selected) is shown in the display. 2. Press the STRIDE button, and the current stride length will start flashing. 3. Press the STRIDE button repeatedly to increase the stride length to the desired value. Each press increases the stride length by 1 centimeter (or 0.1 feet if miles is selected). 4. Release the STRIDE button. After a few seconds, the pedometer will return to the distance function, and the new stride length will be set. Please note that the stride length is important for accurately calculating distance. To find the stride length, you can walk a certain number of steps and measure the distance covered. Then, divide the distance by the number of steps to determine the average stride length. These steps should help you set the stride length on your Silva 56013 pedometer.

How do I switch between displaying the number of steps and the distance on the Silva 56013 pedometer?

To switch between displaying the number of steps and the distance on the Silva 56013 pedometer, follow these steps: 1. Press the MODE button until the text "STEP" is shown in the display to view the number of steps taken. 2. Press the MODE button again until the text "KM" (or "MIL" if miles is selected) is shown in the display to view the distance covered. Please note that the default unit for distance is kilometers, but it can be changed to miles by pressing and holding the MODE and STRIDE buttons simultaneously for 5 seconds. The display will show "MIL" instead of "KM". Repeat the same steps to change back to kilometers. These steps should help you easily switch between displaying the number of steps and the distance on your Silva 56013 pedometer.

How do I reset the Silva 56013 pedometer?

To reset the Silva 56013 pedometer, follow these steps: 1. Press and hold the MODE button for a few seconds until the display shows "RESET". 2. Release the MODE button. 3. Press the STRIDE button to confirm the reset. 4. The pedometer will reset to its default settings, and the step count will be cleared. Please note that resetting the pedometer will erase all stored data, including the step count and any customized settings. Make sure to back up any important data before performing the reset. These steps should help you easily reset your Silva 56013 pedometer to its default settings.

How do I change the default distance unit from kilometers to miles on the Silva 56013 pedometer?

To change the default distance unit from kilometers to miles on the Silva 56013 pedometer, follow these steps: 1. Press and hold the MODE and STRIDE buttons simultaneously for 5 seconds. 2. The display will show "MIL" instead of "KM", indicating that the distance unit has been changed to miles. 3. To change back to kilometers, repeat the same steps by pressing and holding the MODE and STRIDE buttons simultaneously for 5 seconds. Please note that the default distance unit of the pedometer is kilometers, but it can be easily switched to miles using the above steps. This allows you to view the distance covered in the unit that you prefer. These steps should help you change the default distance unit from kilometers to miles on your Silva 56013 pedometer.

Is the manual of the Silva 56013 available in English?

Yes, the manual of the Silva 56013 is available in English .

Is your question not listed? Ask your question here

No results