Siemens WT44C102EE manual

Siemens WT44C102EE
8.9 · 3
PDF manual
 · 8 pages
English
manualSiemens WT44C102EE
1 2 3 4 5
6
End of programme as soon as stop/Îü(finished/anti-crease) indicator light
flashes
Adding or removing laundry
The drying cycle can be interrupted in order to add or remove laundry.
The programme must then be continued or ended.
The drum and the door may be hot!
1. Open the door. The drying process is interrupted.
2. Load or remove laundry and close the door.
3. If required, select a new programme and additional functions.
4. Press the inicio/stop (start/stop) button.
Emptying condensation
Empty the container after every use.
1. Remove the condensation container and hold it
level.
2. Open the locking cap.
3. Pour out the condensation.
Check the valve in the condensation container for dirt:
If there are fluff deposits on the valve
a rinse the valve under
running water. Also pour some tap water into the empty condensation
container then pour it out again through the valve.
To do this, press the valve in and allow all the water to drain out.
4. Regularly remove any deposits in the locking cap hole using
a pointed object.
5. Close the locking cap.
6. Always push the tank fully back in until it locks in place.
If the depósito Èü(container) / limp. ¡°l(cleaning) indicator
light comes on after emptying the container
a see page 10.
Cleaning the fluff filter
Clean the fluff filter after every use.
1. Open the door and pull out the fluff filter.
2. Remove the fluff (brush your hand over the fluff filter).
If the fluff filter is very dirty or blocked, wash it out with warm water
and dry thoroughly.
3. Replace the fluff filter.
4. Remove fluff from door/door area.
Switching off the dryer
Set the programme selector to desactivado (off).
Do not leave laundry in the dryer.
Removing the laundry
Your dryer has an automatic anti-crease function. The drum is moved at set intervals for 30 minutes after
the programme has ended. Laundry remains loose and fluffy (for 90 minutes, if additional menos Ô (easy-
iron) function is selected - depending on model).
... and adapt to individual requirements
Never operate the dryer if it is damaged.
Inform your after-sales service.
Inspecting
the dryer
Sorting and loading laundry
Remove all objects from pockets.
Pay particular attention to cigarette lighters.
The drum must be empty before filling.

Your new dryer

Congratulations - You have chosen to buy a modern, high-quality
Siemens domestic appliance.
A distinctive feature of your dryer is its low energy consumption.
Every dryer which leaves our factory is carefully checked to ensure
that it functions correctly and is in perfect condition.
Should you have any questions, our after-sales service will be pleased
to help.
Disposal in an environmentally-responsible manner
Dispose of packaging in an environmentally-responsible manner.
This appliance is designated according to European directive
2002/96/EC which governs waste electrical and electronic
equipment (WEEE).
The directive provides an EU-wide framework for the return and
recycling of old appliances.
For further information about our products, accessories, spare parts
and services, please visit: www.siemens-home.com

Intended use

Contents Page

ʋ Preparation . . . . . . . . . . . . . . . . . . . . . . 2
ʋ Setting the programmes . . . . . . . . . . . . . 2
ʋ Drying . . . . . . . . . . . . . . . . . . . . . . . . 3/4
ʋ Notes on laundry . . . . . . . . . . . . . . . . . . 5
ʋ Care and cleaning . . . . . . . . . . . . . . . . . . 6
ʋ Overview of programmes . . . . . . . . . . . . 7
ʋ Installation . . . . . . . . . . . . . . . . . . . . . . . 8
ʋ Frost protection / Transport. . . . . . . . . . . 8
ʋ Technical data . . . . . . . . . . . . . . . . . . . . 9
ʋ Optional accessories . . . . . . . . . . . . . . . . 9
ʋ What to do if... / After-sales service . . . . 10
ʋ Safety instructions . . . . . . . . . . . . . . . . 11

Preparing for installation, see page 8

Selecting and adjusting the programme

Drying

Condensation container
Control panel

Care and cleaning

Dryer cabinet, control panel, air cooler, moisture sensors
– Wipe off with a soft, damp cloth.– Do not use abrasive cleaners or solvents.– Remove detergent and cleaning agent residue immediately.Clean the air cooler 5 to 6 times a year or if
depósito Èü(container) / limp. ¡°l(cleaning) flashes after cleaning the fluff filter.
Air cooler
In order to clean it, the air cooler must be removed. Allow the dryer to cool.
Residual water may leak out, so place an absorbent towel underneath
the maintenance door.
1. Unlock the maintenance door (1).
2. Fully open the maintenance door (2).
3. Turn both locking levers outwards (1).
4. Pull out the front insert (2).
5. Remove the air cooler.
Take care not to damage the air cooler.
When cleaning, use warm water only. Do not use hard or sharp-edged objects.
6. Clean the air cooler thoroughly and allow the water to drain off.
Clean the seals.
7. First insert the air cooler (handle at the bottom) and then the front insert.
8. Turn back both locking levers.
9. Lock the maintenance door.
Moisture sensors
The dryer is fitted with stainless steel moisture sensors. The sensors measure the level of
moisture in the laundry. After a long period of operation, a fine layer of limescale may form
on the sensors.
1. Open the door.
2. Clean the moisture sensors using a slightly damp sponge with a rough
surface.
Do not use steel wool or abrasive materials.
Select the drying programme ...
Press the inicio/stop (start/stop) button
1
2
3
Only if your hands are dry.
Only hold the plug by the plug
casing.
Connecting the
mains plug

Drying

Information on laundry ...

Labelling of fabrics
Follow the manufacturer's care information.
( Drying at normal temperature.
'cLow-temperature drying a in addition, select delicado (low heat).
)cDo not machine dry.
Be sure to follow the safety instructions a see page 11!
For example, do not use the dryer for the following fabrics:
Airtight fabrics (e.g. rubber-coated fabrics).
Delicate materials (silk, curtains made from synthetic material) a they may crease.
Laundry contaminated with oil.
Before drying for the first time
Do not put any laundry in the dryer. Set the programme selector to a timed programme
(a see page 7) and select inicio/stop (start/stop). When the programme has finished,
set the programme selector to desactivado (off).
Drying tips
To ensure a consistent result, sort the laundry by fabric type and drying programme.
Always dry very small fabrics (e.g. baby socks) together with large items of laundry
(e.g. hand towels).
Fasten zips, hooks and eyelets, button covers and tie together cloth belts, strips, etc.
Do not overdry easy-care laundry a risk of creasing.
Allow laundry to finish drying in the air.
Do not iron laundry immediately after drying, fold items up and leave for a while a the
remaining moisture will then be distributed evenly.
Knitted fabrics (e.g. T shirts, knitwear) often shrink when tumble dried for the first time
a do not use the extra seco (extra dry) programme.
Starched laundry is not always suitable for dryers a starch leaves behind a coating that
adversely affects the drying operation.
Use the correct dosage of fabric softener as per the manufacturer's instructions when
washing the laundry to be dried subsequently.
Using a timed programme with a small laundry load a optimisation of the drying result.
Environmental protection/energy-saving tips
Before drying, spin the laundry thoroughly in the washing machine a the higher the spin
speed, the shorter the drying time will be (consumes less energy), also spin easy-care
laundry.
Use the maximum recommended fill level but do not overload laundry
a overview of programmes, see page 7.
Make sure the room is well ventilated during drying.
Clean the fluff filter after every drying cycle a see page 4.
Do not block or seal the air inlet.
Only when the appliance is
switched off.
Drum
Programme selector
Only operate the dryer
with the fluff filter inserted.
Air inlet
Fluff filter
ʋ exclusively for domestic use,
ʋ only for drying fabrics which have been washed using
water.
Do not leave children unsupervised near the dryer.
Keep pets away from the dryer.
The dryer may be operated by children from 8
years of age, by persons who have limited
physical, sensory or mental abilities and by
persons who have inadequate experience or
knowledge, provided they are supervised or
have been instructed by a responsible person.
For a detailed programme overview, a see page 7.
Before using the dryer for the first time
run the drying cycle without any laundry a see page 7.
Additional functions/status
and service indicators
ˎ menos Ô
(easy-iron)
Reduces creasing and prolongs the anti-creasing phase
after the programme has finished.
ˎ delicado÷
(low heat)
Reduced temperature for delicate fabrics ', e.g. polyacrylic,
polyamide, elastane or acetate; for longer drying times.
stop/Î finished/anti-crease
depósito Èü
(container)
limp. ¡°l(cleaning)
Lit a empty the container for condensation.
Flashes a clean the fluff filter and/or air cooler.

View the manual for the Siemens WT44C102EE here, for free. This manual comes under the category dryers and has been rated by 3 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the Siemens WT44C102EE or do you need help? Ask your question here

Need help?

Do you have a question about the Siemens and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Siemens WT44C102EE dryer is a freestanding appliance with a rated capacity of 7 kg. Its door hinge is located on the right side, allowing for easy loading and unloading of laundry. The drum volume of this dryer measures 112 liters, providing ample space for drying clothes. In terms of energy efficiency, the Siemens WT44C102EE has been classified as class B. This means that it consumes a moderate amount of energy during operation, which may impact electricity consumption costs. The AC input frequency of this dryer is set at 50 Hz, ensuring compatibility with standard power sources. Additionally, it comes with a 1.45-meter-long cord, allowing for flexible placement within your laundry area. One notable feature of the Siemens WT44C102EE dryer is its LED program stage indicator. This indicator provides clear visual feedback on the current stage of the drying cycle, allowing users to easily monitor the progress of their laundry. In terms of dimensions, this dryer has a width of 600 mm, a depth of 630 mm, and a height of 850 mm. These measurements ensure that the dryer can fit into most standard laundry spaces. Overall, the Siemens WT44C102EE dryer offers an efficient and convenient solution for drying clothes. Its moderate energy consumption, generous drum volume, and LED program stage indicator make it a reliable option for everyday use.

General
BrandSiemens
ModelWT44C102EE | WT44C102EE
Productdryer
EAN4242003608463
LanguageEnglish
FiletypeUser manual (PDF)
Design
Loading typeFront-load
Appliance placementFreestanding
Door hingeRight
Drum volume112 L
Cord length1.45 m
Product colorWhite
Drying system-
Built-in display-
Performance
Drum capacity7 kg
Maximum spin speed- RPM
Cycle time117 min
Noise level67 dB
Power
Energy efficiency classB
AC input voltage220 - 240 V
AC input frequency50 Hz
Connected load2300 W
Annual energy consumption251 kWh
Current10 A
Ergonomics
LED program stage indicatorYes
Weight & dimensions
Width600 mm
Depth630 mm
Height850 mm
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Siemens WT44C102EE below.

What is a condenser dryer?

A condenser dryer is a dryer in which condensation ends up in a reservoir.

What is a drain dryer?

A drain dryer is a dryer in which the warm air and condensation are drained through a hose.

What is the best thing to do about a smelly dryer?

It is best to wipe the dryer drum with a damp cloth and some lemon cleaner.

There is a burning smell from my dryer, now what?

Check the following: - That the fluff filter is clean. - That the bottom of the dryer is free of dust. - That the drain hose is clean. If the above does not help, a mechanic should be called in.

What is the height of the Siemens WT44C102EE?

The Siemens WT44C102EE has a height of 850 mm.

What is the width of the Siemens WT44C102EE?

The Siemens WT44C102EE has a width of 600 mm.

What is the depth of the Siemens WT44C102EE?

The Siemens WT44C102EE has a depth of 630 mm.

What energy label does the Siemens WT44C102EE have?

The Siemens WT44C102EE has energy label B.

Does the Siemens WT44C102EE have a rated capacity of 7 kg?

Yes, the Siemens WT44C102EE has a rated capacity of 7 kg. This means it can accommodate up to 7 kg of laundry in a single load.

Is the appliance placement of the Siemens WT44C102EE freestanding?

Yes, the Siemens WT44C102EE is freestanding. This means it can be placed and operated independently without the need for installation or mounting onto a surface.

Does the Siemens WT44C102EE have a right door hinge?

Yes, the Siemens WT44C102EE has a right door hinge. This means the door opens from the right side, providing convenient access to the drum for loading and unloading.

What is the drum volume of the Siemens WT44C102EE?

The drum volume of the Siemens WT44C102EE is 112 L. This indicates that the dryer has a spacious drum, allowing for efficient drying of larger loads of laundry.

Does the Siemens WT44C102EE have an LED program stage indicator?

Yes, the Siemens WT44C102EE has an LED program stage indicator. This feature provides users with clear visual feedback on the current stage of the drying cycle, enhancing convenience and ease of use.

How do I prepare the Siemens WT44C102EE dryer for use?

To prepare the Siemens WT44C102EE dryer for use, follow these steps: 1. Inspect the dryer to ensure it is not damaged. If you notice any damage, inform your after-sales service. 2. Sort and load your laundry into the dryer. Remove any objects from pockets, paying special attention to cigarette lighters. The drum must be empty before filling it with laundry. 3. Connect the mains plug to a power source. Make sure your hands are dry and hold the plug by the plug casing. 4. Select and adjust the drying programme according to your needs. Use the programme selector to choose the desired programme. 5. If necessary, select additional functions such as easy-iron or low heat for delicate fabrics. 6. Press the start/stop button to begin the drying cycle. 7. During the drying process, periodically check the condensation container. Empty it after every use by removing the container, opening the locking cap, and pouring out the condensation. Clean the valve and the locking cap regularly. 8. After each use, clean the fluff filter by opening the door, pulling out the filter, removing the fluff, and replacing the filter. 9. When you have finished using the dryer, set the programme selector to the off position. 10. Remember to remove your laundry from the dryer promptly to prevent wrinkles. By following these steps, you can properly prepare and use the Siemens WT44C102EE dryer.

How do I set the programmes on the Siemens WT44C102EE dryer?

To set the programmes on the Siemens WT44C102EE dryer, follow these steps: 1. Sort your laundry according to the type of textile and fabric. Ensure that the fabrics are suitable for tumble drying. 2. Load the laundry into the dryer drum, making sure it is empty of any objects or items in the pockets. 3. Connect the dryer to a power source by plugging in the mains plug. 4. Use the programme selector to choose the desired programme for your laundry. Refer to the programme overview in the manual for information on different programmes and their suitability for specific textile types. 5. If needed, select additional functions such as easy-iron or low heat for delicate fabrics. 6. Press the start/stop button to begin the drying cycle. 7. During the drying process, you can adjust the dryness level if available on your model. This allows you to select options like extra dry, cupboard dry, or iron dry. 8. After the drying cycle is complete, remove your laundry promptly to prevent wrinkles. By following these steps, you can easily set the programmes on the Siemens WT44C102EE dryer for efficient and effective drying of your laundry.

What should I do if the drying process is not working properly on the Siemens WT44C102EE dryer?

If the drying process is not working properly on the Siemens WT44C102EE dryer, you can try the following steps to troubleshoot the issue: 1. Check if you have selected the correct programme for your laundry. Refer to the programme overview in the manual to ensure you are using the appropriate programme. 2. Make sure that the dryer is not installed too closely to other objects. Provide adequate air circulation around the dryer to prevent overheating. 3. If there is a mains failure, restart the dryer once the power is restored. 4. Clean the moisture sensors if there is a fine layer of limescale on them. Refer to the cleaning instructions in the manual for guidance. 5. If your laundry is still damp after drying, consider using the next drying programme up or using the timed programme as a supplement. 6. Check the humidity in the room. If it has significantly increased, ensure that the room is sufficiently ventilated. 7. Clear any obstructions in the air inlet and make sure that the air cooler is properly inserted. 8. If one or more indicator lights are flashing, clean the fluff filter and air cooler as instructed in the manual. 9. Verify that the installation conditions, as specified in the manual, are met. 10. In case of a power failure, remove the laundry from the dryer immediately and spread it out to prevent heat from escaping. By following these steps, you can troubleshoot and resolve issues with the drying process on the Siemens WT44C102EE dryer.

Are there any specific notes on laundry that I should be aware of when using the Siemens WT44C102EE dryer?

When using the Siemens WT44C102EE dryer, there are specific notes on laundry that you should be aware of. Here are the key points: 1. Sort your laundry according to the type of textile and fabric. Fabrics must be suitable for tumble drying. 2. Refer to the programme overview in the manual to select the appropriate programme for your laundry. Different programmes are designed for specific textile types. 3. Pay attention to the recommended maximum load capacity for each programme. For example, the "algodón/algodão" programme can handle a maximum load of 7 kg, while the "sintéticos" programme can handle up to 3.5 kg. 4. Take note of the different dryness levels that can be selected, such as "extra seco" (extra dry), "seco para guardar" (cupboard dry), and "seco para Ôü(iron dry)" (iron dry). Adjust the dryness level according to your preference and the type of laundry. 5. Multi-layered textiles may require a longer drying time compared to single-layered items. It is recommended to dry them separately. 6. Regularly clean the fluff filter and air cooler as instructed in the manual to maintain optimal drying performance. By following these specific notes on laundry, you can ensure effective and efficient drying results with the Siemens WT44C102EE dryer.

How do I care for and clean the Siemens WT44C102EE dryer?

To care for and clean the Siemens WT44C102EE dryer, follow these steps: 1. Dryer Cabinet and Control Panel: - Wipe off the dryer cabinet and control panel with a soft, damp cloth. - Avoid using abrasive cleaners or solvents. - Immediately remove any detergent or cleaning agent residue. 2. Air Cooler: - Allow the dryer to cool down before cleaning the air cooler. - Place an absorbent towel underneath the maintenance door to catch any residual water. - Unlock and fully open the maintenance door. - Turn both locking levers outwards and pull out the front insert. - Carefully remove the air cooler, taking care not to damage it. - Clean the air cooler thoroughly using warm water only. Avoid using hard or sharp-edged objects. - Allow the water to drain off and clean the seals. - Insert the air cooler back into place, followed by the front insert. - Turn back both locking levers and lock the maintenance door. 3. Moisture Sensors: - Open the dryer door. - Clean the moisture sensors using a slightly damp sponge with a rough surface. - Avoid using steel wool or abrasive materials. By following these steps, you can effectively care for and clean the Siemens WT44C102EE dryer, ensuring its optimal performance and longevity.

Is the manual of the Siemens WT44C102EE available in English?

Yes, the manual of the Siemens WT44C102EE is available in English .

Is your question not listed? Ask your question here

No results