Siemens WM12E227EP manual

Siemens WM12E227EP
(1)
  • Number of pages: 6
  • Filetype: PDF
1

Safety instructions

The washing machine is heavy - take care when lifting.
Caution: frozen hoses may rip/burst. Do not install the washing machine in areas exposed
to frost or outdoors.
The washing machine could be damaged. Do not lift the appliance by protruding
components (e.g. the washing machine door).
In addition to the instructions provided in this document, special regulations from the
relevant water and electric utility companies may apply.
If in doubt, have a technician connect the appliance.
Lay hoses and cables in such a way that there is no risk of tripping.

Installation surface

The machine must be stable so that it does not move around.
The installation surface must be firm and level.
Soft floors/floor coverings are not suitable.

Installation on a pedestal

The feet of the washing machine must be secured with holding brackets*.
* order no. WMZ2200, WX9756, CZ110600, Z7080X0

Installation on a wood joist floor

If possible, place the washing machine in a corner.
Screw a water-resistant wooden board (min. 30 mm thick) to the floor.
The feet of the washing machine must be secured with holding brackets*.
* order no. see above

Installing the appliance

Install the appliance before connecting it to the power supply.

Installation in a kitchenette (underneath the worktop or fitted in a cabinet)

Recess width of 60 cm required.
Only install the washing machine underneath a continuous worktop that is securely
connected to adjacent cabinets.

Installation underneath the worktop

Risk of electric shock.
Instead of the appliance covering plate, you must have a metal cover * fitted by an expert.
* order no. WMZ2420, WZ10190
Recess width of 60 cm required.
2

Scope of delivery depending on model

Also required, depending on the connection:

1 hose clamp Ø 24-40 mm (exclusive dealers) to connect to a siphon
a page 4; water connection.

Useful tools

Spirit level for installation.

Hose and cable lengths depending on model

Left-hand connection

or

Right-hand connection

Available from specialist dealers/the after-sales service:
Extension for Aqua-Stop or cold-water inlet hose (approx. 2.50 m).
order no. WMZ2380, WZ10130, CZ11350, Z7070X0
Longer inlet hose (approx. 2.20 m) for standard model.
Mains cable
Water outlet
Water inlet
Elbow
for fixing the drainage
hose in place
Covers
A
quaä
St
op
A
quaä
S
ecure
St
an
d
ar
d
Wrench
(depending on model)
~
145 cm
~
100 cm
~
90 cm
~
140 cm
~
145 cm
min. 60 cm
~
90 cm
max. 100 cm
Moisture inside the drum is
due to final testing.
3

Removing the transport braces

Before using the appliance for the first time, make sure that you
completely remove transport braces and keep them for subsequent
transportation.
If you need to transport the appliance at a later date, always re-affix the
transport braces to prevent damage to the machine a page 6.
Store the screw and sleeve screwed together.
1. Take the hoses and elbow out of the holders, depending on model.
2. Loosen the bolts ....
... until they move freely in the sleeves.
3. Completely remove all 4 transportation protection devices (each bolt
together with sleeve) and take the main cable out of the holder.
Always displace bolt and sleeve together as shown in the illustration.
All bolts and sleeves must be removed.
4. Insert covers.
4

Water connection depending on model

Risk of electric shock. Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).
To prevent leaks or water damage, observe the instructions in this
section.
Caution: only operate the washing machine using cold drinking water.
Do not connect to the mixer tap of an unpressurised hot-water boiler.
Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
If in doubt, have a technician connect the appliance.

Water inlet

Water inlet hose:
Caution: do not bend, squash, modify or cut through
(otherwise its strength is no longer guaranteed).
Optimum water pressure in the supply network: 100ä1,000 kPa (1ä10 bar)
When the tap is on, the water flow is at least 8 l/min.
If the water pressure is higher than this, a pressure reducing valve must be installed.
Model: AquaäStop
AquaäSecure
Standard
1. Connect the water inlet hose to the tap.
Caution: only tighten the screw connections by
hand.
2. Open the water tap carefully, checking the leak
tightness of the connection points.
Caution: the screw connection is under mains water
pressure.

Water outlet

Water outlet hose:
Caution: do not bend or pull lengthways.
Height difference between the installation surface and the drain:
min. 60 cm - max. 100 cm
Outlet in a sink
Caution: secure the drain hose from slipping out.
Caution: the plug must not block drainage from the sink. During
pumping, check whether the water is draining away quickly enough.
The end of the drain hose must not be immersed in the water pumped
out. This risks water being sucked back into the washing machine.
Drainage into a siphon:
Caution: the connection point must be secured with a hose clamp,
Ø 24-40 mm (exclusive dealers).
max.
90°
max.
90°
min.
10 mm
min.
10 mm
3/4”
3/4”
Siemens WM12E227EP

Need help?

Number of questions: 0

Do you have a question about the Siemens WM12E227EP or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Siemens WM12E227EP owners to properly answer your question.

View the manual for the Siemens WM12E227EP here, for free. This manual comes under the category Washing Machines and has been rated by 1 people with an average of a 6.5. This manual is available in the following languages: English. Do you have a question about the Siemens WM12E227EP or do you need help? Ask your question here

Siemens WM12E227EP specifications

General
Brand Siemens
Model WM12E227EP
Product Washing Machine
Language English
Filetype PDF
Power
Energy efficiency class (old) A++
Energy consumption washing per cycle - kWh
Current 10 A
AC input voltage 220 - 240 V
AC input frequency 50 Hz
Water consumption per cycle - L
Other features
Annual water consumption washing 10560 L
Annual energy consumption washing 197 kWh
Washing class A
Design
Built-in display
Loading type Front-load
Cord length 1.6 m
Door hinge Left
Door opening angle 90 °
Drum volume 55 L
Water fill Cold
Certification CE, VDE
Drum material Stainless steel
Control type Buttons,Rotary
Product colour White
Door colour White
Ergonomics
Appliance placement Freestanding
Child lock
Remaining time indication
Performance
Number of washing programs -
Rated capacity 7 kg
Maximum spin speed 1200 RPM
Spin-drying class B
Noise level (wash) 59 dB
Delayed start timer
Foam control system
Delay start (max) 24 h
Noise level (spin) 76 dB
Weight & dimensions
Width 600 mm
Depth 590 mm
Height 848 mm
Weight 81000 g
Technical details
Sustainability certificates ENERGY STAR
Washing programs
Hygiene/anti-allergy washing program
Black washing program
Mix washing program
Pre-wash program
Quick washing program
show more

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Siemens WM12E227EP.

Is your question not listed? Ask your question here