Siemens SC 76M530 manual
PDF manual · 24 pages English
View the manual for the Siemens SC 76M530 here, for free. This manual comes under the category Dishwashers and has been rated by 1 people with an average of a 9.3. This manual is available in the following languages: English. Do you have a question about the Siemens SC 76M530 or do you need help? Ask your question here
- *9000545219*
- 9000545219 en (9102-1) 550MA
- en Table of contents
- Please read the operating and installation instructions carefully. They contain important information on how to install, use and maintain the appliance.
- Retain all documents for subsequent use or for the next owner.
- Read the “Installation” chapter to learn how to install and connect the appliance correctly.
- m Warning
- Knives and other utensils with sharp points must be placed in the cutlery basket with the points downwards or horizontally on the knife shelf *.
- * depending on model
- The description of the childproof lock is at the back in the envelope.
- * depending on model
- You can secure your appliance from being unintentionally the programme terminated (e.g. improper operation by children).
- Activating the button lock:
- If any button is pressed while the programme is running, this ’– is indicated on the digital display. It is not possible to end (Reset) the programme.
- Deactivating the button lock:
- When the programme ends (‹:‹‹ on the digital display), the button lock is cancelled. If there is a power failure, the button lock is retained. Whenever a programme is restarted, the button lock must be reactivated.
- m Warning
- Children could become locked in the appliance (risk of suffocation) or find themselves in other dangerous situations.
- Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed.
- Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front.
- Individual positions are referred to in the text.
- (
- ON/OFF switch
- 0
- Programme buttons **
- 8
- Timer programming *
- @
- Additional options **
- H
- START button
- P
- Display “Check water supply”
- X
- Rinse aid refill indicator
- `
- Digital display
- * depending on model
- ** Number depending on model
- 1"
- Top basket
- 1*
- Top spray arm
- 12
- Bottom spray arm
- 1:
- Filters
- 1B
- Cutlery basket
- 1J
- Bottom basket
- 1R
- Dispenser for rinse aid
- 1Z
- Detergent dispenser
- 1b
- Lock for detergent dispenser
- 1j
- Rating plate
- * depending on model
- As soon as the rinse-aid refill indicator X is lit on the fascia, there is still a rinse-aid reserve of 1 – 2 rinsing processes. Refill with rinse aid.
- The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers.
- Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used.
- The amount of rinse aid dispensed can be set from §:‹‹ to §:‹‡. This is the factory setting §:‹….
- Do not change the amount of rinse aid unless streaks (select lower setting) or water stains (select higher setting) are left on the utensils.
- If the rinse-aid refill indicator X is impaired (e.g. when using combined detergents containing rinse aid component), it can be switched off.
- The rinse aid refill indicator X is now switched off.
- Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles.
- Causes:
- Recommendation:
- Very small utensils should not be washed in the machine, as they may fall out of the baskets.
- To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom up.
- Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
- Top basket 1"
- Bottom basket 1J
- Tip
- Heavily soiled utensils (pans) should be placed in the bottom basket. The more powerful spray jet provides a better dishwashing result.
- You should always place cutlery unsorted with the points downwards.
- * depending on model
- The spikes can be folded down to improve arrangement of pans, bowls and glasses.
- * depending on model
- Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder.
- You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing up liquid. The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling. Tablets contain an adequately l...
- Note
- To ensure a good washing result, always follow the instructions on the detergent packaging!
- If you have further questions, we recommend that you contact the detergent manufacturers’ helpline.
- m Warning
- Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents.
- Tip
- If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate.
- Suitable detergents and care products can be purchased online via our website or via customer service (see back page).
- The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. The programme data has been measured in the laboratory according to AS/NSZ 2007.
- Programme
- Type of utensils and soiling
- Programme sequence
- Possible additional options
- Programme data
- 1.) Duration: hs/ mins
- 2.) Energy consumption in kWh
- 3.) Water consumption in litres
- 4.) With Aquasensor
- ª
- Pots and Pans 70°
- Pots, utensils and cutlery
- Highly soiled
- Prerinse
- Clean 70°
- Intermediate rinse
- Final rinse 70°
- Dry
- All
- 1.) 2:20
- 2.) 1,20
- 3.) 10
- 4.) 8
- ± / °
- Intensive 65°
- Pots, utensils and cutlery
- Highly soiled
- Prerinse
- Clean 65°
- Intermediate rinse
- Final rinse 70°
- Dry
- All
- 1.) 2:40
- 2.) 1,15
- 3.) 9
- 4.) 9
- ¹
- Auto 45° – 65°
- Utensils and cutlery
- Normally soiled
- Is optimised according to the soiling with the aid of sensors.
- All
- 1.) 1:40 - 2:50
- 2.) 0,6 - 1,15
- 3.) 6 - 11
- 4.) 6 - 11
- Ù / Ø
- Normal 45°
- Utensils and cutlery
- Normally soiled
- Prerinse
- Clean 45°
- Intermediate rinse
- Final rinse 45°
- Dry
- All
- 1.) 2:40
- 2.) 0,49
- 3.) 10,1
- 4.) -
- ñ / ð
- Quick 45°
- Utensils and cutlery
- Lightly soiled
- Clean 45°
- Intermediate rinse
- Final rinse 55°
- Extra drying
- 1.) 0:35
- 2.) 0,50
- 3.) 6
- 4.) -
- ù / ø
- Prerinse
- Lightly soiled
- Prerinse
- None
- 1.) 0:15
- 2.) 0,05
- 3.) 3
- 4.) -
- You can select a suitable programme according to the type of utensils and degree of soiling.
- Test institutes can request the conditions for running comparison tests by sending an e-mail to
- dishwasher@test-appliances.com.
- Quote the appliance number (ENr.) and the production date (FD) which you can find on the rating plate 1j on the appliance door.
- * depending on model
- Additional options can be set with the buttons @.
- The >>Express Wash/ Speed Perfect<< function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. The change in the running time is indicated on the digital display `. To obtain optimum cleaning results at a re...
- The temperature is increased during the cleaning process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles.
- Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly.
- An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption.
- * depending on model
- The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water.
- The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 2–4 litres. If the turbidity is greater, the water is drai...
- When the programme is selected, the remaining running time of the programme is indicated on the digital display `.
- The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
- * depending on model
- You can delay the start of the programme in 1-hour steps up to 24 hours.
- The programme has ended when the value ‹:‹‹ is indicated on the numerical display `.
- * depending on model
- To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting).
- Automatic disconnection can be adjusted from ˜:‹‹ to ˜:‹ƒ.
- ˜:‹‹
- Appliance does not switch off automatically
- ˜:‹‚
- Off after 1 min
- ˜:‹ƒ
- Off after 120 min
- Short time after the end of the programme:
- m Warning
- At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops.
- When the START button H has been pressed, the programme cannot be changed.
- The only way a programme can be changed is by Cancel programme (Reset).
- The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!)
- A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems.
- If you find such deposits:
- Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers.
- Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage.
- Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces.
- Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
- m Warning
- Never use other chlorinated household detergents! Health hazard!
- The filters 1: keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters.
- The filter system consists of a coarse filter, a flat fine filter and a microfilter.
- Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1* and 12.
- The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to elimina...
- Note
- If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset).
- (See chapter entitled “Dishwashing”)
- m Warning
- If on the digital display ` an error code (“:‹‚ to “:„‹), always disconnect the appliance from the power supply and then turn off the tap.
- You can rectify certain faults yourself (see following fault description), for all other faults please contact customer service and state the indicated fault “:XX.
- m Warning
- Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at c...
- Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter.
- In this case:
- If the advice given does not resolve your problem, please contact your customer service. Contact details can be found on the back cover of this instruction manual or in the enclosed customer service list. When calling , please quote the appliance num...
- Rely on the expertise of the manufacturer. Call us to ensure that the repair will be carried out by fully-trained service engineers, who are equipped with original spare parts for your appliance.
- The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragr...
- Install the appliance in the correct sequence:
- Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle.
- Weight:
- max. 27 kg
- Voltage:
- 220–240 V, 50 Hz or 60 Hz
- Connected load:
- 2.0–2.4 kW
- Fuse:
- 10/16 A
- Water pressure:
- at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
- Inlet rate:
- minimum 10 litres/minute
- Water temperature:
- for cold water connection only.
- The required installation dimensions can be found in the installation instructions. Level the appliance. Ensure that the appliance is situated securely on the floor.
- Also observe the sequence of worksteps here.
- Empty the dishwasher and secure loose parts.
- Transport appliance upright only.
- (This prevents residual water from running into the machine control and damaging the programme sequence.)
- If the appliance is in a room where there is a risk of frost (e.g. holiday home), empty the appliance completely (see Transportation).
- Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials.
- Please dispose of the individual parts separated according to type.
- Please ask your dealer or inquire at your local authority about current means of disposal.
- All plastic parts of the appliance are identified with internationally standardised abbreviations (e.g. >PS< polystyrene). Therefore, plastic waste can be sorted out when the appliance is being disposed of.
- Please follow the safety instructions under “Delivery”.
- Please follow the safety instructions under “Disposal of your appliance”.
- This appliance is identified according to the European guideline 2002/96/EC on waste electrical and electronic equipment – WEEE. The guideline specifies the framework for an EU-wide valid return and re-use of old appliances.
- *9000545219*
- 9000545219 en (9102-1) 550MA
General
| Siemens | |
| SC 76M530 | |
| Dishwasher | |
| English | |
| User manual (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Siemens SC 76M530 below.
What do I do about a smelly dishwasher?
Do you have to pre-rinse the dishes?
How much dishwashing detergent should I use?
How do I add softening salt to my dishwasher?
Is the manual of the Siemens SC 76M530 available in English?
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Siemens and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Siemens owners to provide you with a good answer.
Number of questions: 0