Siemens SC 76M530 manual

Siemens SC 76M530
9.3 · 1
PDF manual
 · 24 pages
English
manualSiemens SC 76M530
en
13
Aqua sensor

Aqua sensor *

* depending on model
The Aqua sensor is an optical measuring
device (light barrier) which measures the
turbidity of the rinsing water.
The Aqua sensor is used according to the
programme. If the Aqua sensor is active,
“clean” rinsing water can be transferred to
the next rinse bath and water consumption
can be reduced by 2–4 litres. If the
turbidity is greater, the water is drained
and is replaced with fresh water. In the
automatic programmes the temperature
and running time can also be adjusted to
the degree of soiling.

Switching on the appliance

Turn on the tap fully.
Switch on ON/OFF switch (.
The display of the last selected
programme flashes. This programme
remains selected if no other
programme button 0 is pressed. The
expected programme duration flashes
on the digital display `.
Press the START button H.
The programme starts running.

Remaining running time display

When the programme is selected, the
remaining running time of the programme
is indicated on the digital display `.
The running time is determined during the
programme by the water temperature, the
number of utensils as well as the degree
of soiling and may vary (depending on the
selected programme).
Timer programming

Timer programming *

* depending on model
You can delay the start of the programme
in 1-hour steps up to 24 hours.
Close the door.
Switch on ON/OFF switch (.
Press button 8 + until the digital
display ` jumps to œ:‹‚.
Press 8 + or – button until the
displayed time corresponds with your
requirements.
Press START button H, timer
programming is activated.
To delete timer programming, press
the 8 + or – button until ` œ:‹‹ is
indicated on the digital display.
You can change your programme
selection at any time until the
programme starts.

End of programme

The programme has ended when the
value :‹‹ is indicated on the numerical
display `.
Switching off automatically after the end of the pr ogramme

Switching off automatically after

the end of the programme *

* depending on model
To save energy, the dishwasher is
switched off 1 minute after the programme
ends (factory setting).
Automatic disconnection can be adjusted
from ˜:‹‹ to ˜:‹ƒ.
Close the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button H until š:... is
indicated on the digital display.
Release both buttons.
Press programme button # until the
factory set value ˜:‹‚ is indicated on
the digital display `.

Washing the dishes

˜:‹‹ Appliance does not switch off
automatically
˜:‹‚ Off after 1 min
˜:‹ƒ Off after 120 min
s

View the manual for the Siemens SC 76M530 here, for free. This manual comes under the category Dishwashers and has been rated by 1 people with an average of a 9.3. This manual is available in the following languages: English. Do you have a question about the Siemens SC 76M530 or do you need help? Ask your question here

Need help?

Do you have a question about the Siemens and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Siemens owners to provide you with a good answer.

Number of questions: 0

General
Siemens
SC 76M530
Dishwasher
English
User manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Siemens SC 76M530 below.

Is your question not listed? Ask your question here

No results