Siemens iQ500 WT47G439EE manual

Siemens iQ500 WT47G439EE
6.9 · 3
PDF manual
 · 44 pages
English
manualSiemens iQ500 WT47G439EE
Faults and what to do about them en
37

3 Faults and what to do about them

Faults and what to do about them
Faults Cause/remedy
Ì on the display panel
and drying has been
interrupted.
Empty the condensate container; ~ Page 32 and the dryer; ~ Page 15.
If the optional condensation drain* is installed, the drain hose may be
blocked or kinked. Check the hose for deposits and rinse the hose. Lay
the hose without any kinks.
¥ on the display panel. Clean the fluff filter and press the Start button ~ Page 31.
selfCleaning on the é
display panel.
Not a fault. The heat exchanger is cleaned automatically. Do not pull out
the condensate container while this is displayed.
Dryer does not start. Mains plug plugged in or fuse checked?
Programme selected? Select a programme.
Dryer door open? Close the door.
Is the childproof lock activated? Deactivate the childproof lock.
"Ready in" time selected? Programme starts after a delay ~ Page 26.
Creasing. Creasing occurs when you have exceeded the maximum load or selected
the wrong programme for the type of fabric. All the required information
can be found in the programme table ~ Page 24.
Remove clothes immediately after drying; creasing may occur if they are
left in the drum.
Water is leaking out. Not a fault; the dryer may be positioned on an incline. Level the dryer.
Change in the pro-
gramme duration dis-
played during drying.
Not a fault. The moisture sensors detect the remaining moisture in the load and
adjust the programme length (except timed programmes).
Laundry is not dried cor-
rectly or is still too damp.
After the end of the programme, warm laundry feels damper than it actually
is. Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but does not
increase the temperature. Your laundry will become drier ~ Page 26.
Select a programme with a longer drying time or increase the drying level.
This does not increase the temperature.
Select a timed programme for subsequent drying of laundry that is still
damp ~ Page 24.
If you have exceeded the maximum load for the programme, the laundry
may not be dried properly.
Clean the moisture sensor in the drum. The sensor may become covered by
a fine layer of limescale or residues of detergents and care products which
then impair its function. Your laundry is not being dried correctly
~ Page 35.
Drying has been interrupted as a result of a power cut, because the conden-
sate container is full or because the maximum drying time has been
exceeded.
Note: See also the laundry tips ~ Page 23.
* Depending on the model

View the manual for the Siemens iQ500 WT47G439EE here, for free. This manual comes under the category dryers and has been rated by 3 people with an average of a 6.9. This manual is available in the following languages: English. Do you have a question about the Siemens iQ500 WT47G439EE or do you need help? Ask your question here

Need help?

Do you have a question about the Siemens and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Siemens iQ500 WT47G439EE is a dryer designed to provide efficient and reliable drying performance. With its sleek and modern design, it offers a stylish addition to any laundry room. This dryer is equipped with advanced features to ensure optimal drying results. It has a generous capacity, allowing for large loads to be dried at once, saving time and energy. The iQ500 WT47G439EE also offers a variety of drying programs to accommodate different fabric types and laundry needs. Featuring sensor-controlled autoDry technology, this dryer continuously monitors the moisture levels in the drum and adjusts the drying time accordingly. This ensures that clothes are dried to perfection without the risk of over-drying or shrinkage. The WT47G439EE is equipped with a self-cleaning condenser which automatically cleans itself during the drying process, ensuring efficient and consistent drying performance over time. Operating the iQ500 WT47G439EE is simple and intuitive, thanks to its easy-to-use control panel. It also offers a convenient delay start function, allowing you to set the drying process to start at a later time to suit your schedule. In terms of energy efficiency, the iQ500 WT47G439EE is designed to save both electricity and money. It has been awarded the highest energy efficiency rating, making it an environmentally friendly choice. Overall, the Siemens iQ500 WT47G439EE is a reliable and efficient dryer that offers a range of features to ensure optimal drying performance.

General
BrandSiemens
ModeliQ500 WT47G439EE
Productdryer
LanguageEnglish
FiletypeUser manual (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Siemens iQ500 WT47G439EE below.

What is a condenser dryer?

A condenser dryer is a dryer in which condensation ends up in a reservoir.

What is a drain dryer?

A drain dryer is a dryer in which the warm air and condensation are drained through a hose.

What is the best thing to do about a smelly dryer?

It is best to wipe the dryer drum with a damp cloth and some lemon cleaner.

There is a burning smell from my dryer, now what?

Check the following: - That the fluff filter is clean. - That the bottom of the dryer is free of dust. - That the drain hose is clean. If the above does not help, a mechanic should be called in.

How do I select the appropriate drying program for different types of laundry?

Use the dryer's easy-to-navigate interface to select the desired drying program based on the type of laundry you are drying. Each program is optimized for specific fabrics and load sizes, ensuring efficient and effective drying results.

What is the maximum load capacity for the Siemens iQ500 WT47G439EE dryer?

The Siemens iQ500 WT47G439EE dryer has a generous maximum load capacity of 9 kilograms, allowing you to dry large laundry loads with ease.

How can I ensure energy-efficient operation while using the dryer?

To promote energy efficiency, you can utilize the sensors integrated into the dryer that automatically adjust the drying time and energy consumption based on the moisture levels detected in the load. Additionally, make sure to clean the lint filter regularly to optimize airflow and enhance drying performance.

How can I prevent wrinkling of clothes during the drying process?

To minimize wrinkles, you can select the appropriate drying program, such as the "Easy Iron" or "Delicate" settings, which offer lower heating intensity and shorter drying times. Additionally, promptly removing the laundry from the dryer at the end of the cycle and placing it neatly can help reduce creasing.

Can I delay the start time of the drying cycle to fit my schedule?

Absolutely! The Siemens iQ500 WT47G439EE dryer features a convenient delay start function that enables you to set a desired time delay for the drying cycle to begin. This way, you can ensure that your laundry finishes drying precisely when you need it.

Is the manual of the Siemens iQ500 WT47G439EE available in English?

Yes, the manual of the Siemens iQ500 WT47G439EE is available in English .

Is your question not listed? Ask your question here

No results