Siemens iQ300 WT44E107FI manual

Siemens iQ300 WT44E107FI
8.5 · 22
PDF manual
 · 8 pages
English
manualSiemens iQ300 WT44E107FI
7
Programme overview also see Page 5
Sort the laundry according to type of textile and fabric. Fabrics must be suitable for tumble drying.
After drying...
ciron laundry lightly iron laundry @cdo not iron laundry cmangle laundry
PROGRAMMES TEXTILE TYPE AND INFORMATION
*Ê Cottons max. 7 kgHard-wearing fabrics, boil-resistant fabrics made of cotton or linen.*Ï Easy-Caremax. 3.5 kgNon-iron laundry made of synthetic fibres and blended fabric, easy-care cotton.
Ô Iron Dry c÷@c
Fabrics suitable for ironing (iron fabrics in order to avoid creasing).· Cupboard Dry @Single-layer fabrics. Cupboard Dry Plus @Fabrics made of thick, multilayered items of clothing. Time programme warm 20minmax. 3 kg
Pre-dried, multi-layered, sensitive fabrics made of acrylic fibres, or separate small items of laundry. Also for subsequent
drying.x Super 40’max. 2 kgLaundry made of synthetic fibres, cotton or blended fabrics (for example) that needs to be dried quickly. The values
may differ from the those specified depending on the type of fabric, mixture of laundry to be dried, residual moisture in
the fabric and loading capacity.üOutdoormax. 1.5 kgFabrics with membrane coating, water-repellent fabrics, functional clothing, fleece fabrics (dry jackets/trousers with removable internal lining separately).
*Dryness levels can be selected individually a÷Cupboard Dry Plus, ·üCupboard Dry and Ô Iron Dry (depending on the model). Degree of dryness can be finely adjusted;
multi-layered textiles require a longer drying time than single-layered items of clothing. Recommendation: Dry separately.
9702 / 9001268418

*1268418*

BSH Hausgeräte GmbHCarl-Wery-Straße 3481739 München/GERMANYWT44E107FIManufactured by BSH Hausgeräte GmbH under Trademark License of Siemens AG
8

Installation

Delivery specification: dryer, instructions for installation and use, woollens basket (depending on model).Check dryer for transport damage.The dryer is very heavy. Do not attempt to lift it on your own.Be careful to avoid sharp edges.Do not lift the dryer by any of the protruding parts (e.g. the door) as they may break off.Do not set up in a room that is susceptible to frost. Freezing water may cause damage. If in doubt, have the appliance connected by an expert.Setting up the dryerThe appliance plug must always be accessible.Ensure that the appliance is installed on a clean, level and solid surface.Keep the cooling grille at the front of the dryer unobstructed.Keep the area around the dryer clean.Make the dryer level using the threaded feetand a spirit level.Do not remove the threaded feet under any circumstances.
Mains connection see safety instructions a Page 11.
Connect to an AC earthed socket. If in doubt have the socket checked by an expert.
The mains voltage and the voltage shown on the rating plate (a Page 9) must correspond.
The connected load and necessary fuse protection are specified on the rating plate.
Converting the installed load Note the fuse protection of the socket.
16/10 Amps

Frost protection / Transport

Preparation
1. Empty the condensate container a page 4.
2. Select any programme using the programme selector.
3. Press the start button a condensation is pumped into the container.
4. Wait 5 min. and then empty the condensate container again.
5. Turn the programme selector to Off.
1.
Take all accessory parts out of the drum.The drum must be empty.Make sure that the airinlet remains unobstructed Clean and level
2.
3.
turn to
Off
press and hold selection then turn 3 x to the rightturn to
Off
set
amperage1 x to the rightFeedback (depending on model):
off
flashes
10 A
16 A
Do not operate the dryer if there is a danger of frost.Do not set up the dryer behind a door or sliding door as this may obstruct or prevent the dryer door from opening. This will prevent a potentially fatal danger to children from locking themselves in.
9
Technical data
ʠ
Dimensions (DxWxH) 60 x 60 x 85 cm (height adjustable)
Weight approximately 45 kg
Max. capacity 7 kg
Condensate container 4.2 l
Connection voltage
Connected load
Fuse protection see appliance rating plate
Ambient temperature
Product number/
Production number
You can find the rating plate on the back of the dryer.
Power consumption when switched off 0.10 W
Power consumption when ready for use (left-on mode) 1.00 W
Consumption values table
Programme
Spin speed which is
used for spinning
the laundry
Duration** Energy consumption**
ÊüCottons
7 kg 3.5 kg 7 kg 3.5 kg
10 A 16 A 10 A 16 A 10 A 16 A 10 A 16 A
·üCupboard Dry* 1400 rpm 112 min 98 min 93 min 63 min 3.67 kWh 3.54 kWh 2.02 kWh 1.95 kWh
1000 rpm 131 min 115 min 100 min 70 min 4.28 kWh 4.13 kWh 2.36 kWh 2.27 kWh
800 rpm 150 min 133 min 116 min 86 min 4.90 kWh 4.72 kWh 2.89 kWh 2.79 kWh
ÔüIron Dry* 1400 rpm 93 min 69 min 78 min 48 min 2.65 kWh 2.55 kWh 1.83 kWh 1.78 kWh
1000 rpm 111 min 82 min 87 min 57 min 3.34 kWh 3.22 kWh 2.30 kwh 2.23 kwh
800 rpm 130 min 94 min 98 min 68 min 4.05 kWh 3.90 kWh 2.89 kwh 2.81 kwh
ÏüEasy-Care 3.5 kg 3.5 kg
·üCupboard Dry* 800 rpm 48 min 42 min 1.39 kWh 1.35 kWh
600 rpm 60 min 51 min 1.70 kWh 1.65 kWh
* Programme setting for testing in accordance with the applicable EN61121 standard.
** The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual moisture in the laundry, the degree
of dryness that has been set, the amount of laundry being loaded, the environmental conditions, and any additional functions that have been activated.
Most efficient programme for cotton fabrics
The following "standard cottons programme" (identified with ) is suitable for drying normal, wet cotton laundry and is most efficient in terms of
its combined energy consumption for drying wet cotton laundry.
Standard programme for cottons in accordance with current EU regulation 932/2012
Programme Load Energy consumption Programme duration
Cottons Cupboard Dry 7 kg/3.5 kg
16 A 16 A
4.13 kWh/2.27 kWh 115 min/70 min
Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
The consumption values are determined using a circuit breaker/fuse rating of 16 A.
Optional accessories (from after-sales service using order number, depending on model)
Platform
For easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth to save space. The dryer must be fastened
to the washing machine using this connection set. With pull-out worktop: WZ 20300
Connection fittings for condensation outlet
The condensation is conveyed directly via a hose.
Installation underneath the worktop
Instead of the appliance covering plate, you must have a metal cover fitted by a specialist.
WZ
20500
WZ
20310
WZ
20160
WZ
20290
10

What to do if ...

If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales service. We
will always find an appropriate solution and will avoid unnecessary visits by engineers. Trust the
expertise of the manufacturer and rest assured that the repair will be carried out by trained service
technicians using original spare parts. The contact details of your local after-sales service can be found
in the enclosed after-sales service directory, or by calling one of these numbers:
GB 0344 892 8999 (Calls charged at local or mobile rate.)
IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
When contacting the after-sales service, please quote the appliance's product number (E no.) and
production number (FD) (see the inside of the door).
Set the programme selector to Off and remove the appliance plug from the socket.
ʠ
The start indicator lamp
does not light up.
Mains plug plugged in?
Programme selected?
Check the socket fuse.
ʠ
The display panel light and
indicator lights (depending on
model) go out and the start
indicator light flashes.
Energy-saving mode is activated a see the separate Energy-saving
mode instructions.
ʠ
The Í(Empty water) and
start indicator lamp flash.
Empty the condensate container.
If featured, check hose for condensation outlet.
ʠ
The x (Clean filter) and
start indicator lamp flash.
Clean the fluff filter and/or air cooler under running water
aPage 4/6.
ʠ
Dryer does not start. start button selected?
Door closed?
Ambient temperature greater than 5°C? The optimum ambient
temperature for drying is between 5 °C and 35 °C.
ʠ
Water is running out. Align dryer horizontally.
Clean air cooler seal.
ʠ
The door opens by itself. Push the door closed until you hear it engage.
ʠ
Creasing. Laundry load exceeded?
Remove articles of clothing immediately after the end of the
programme, hang up and pull into shape.
Unsuitable programme selected a Page 7.
ʠ
Laundry is not dried correctly
or is still too damp.
After the end of the programme, warm laundry feels damper than it
actually is. Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but does
not increase the temperature. Your laundry will become drier.
Select a programme with a longer drying time or increase the drying
level. This does not increase the temperature.
Select a time programme for extended drying of laundry that is still
damp.
If you have exceeded the maximum load for the programme, the
laundry may not be dried correctly.
Clean the moisture sensor in the drum. A fine layer of limescale may
adversely affect the performance of the sensors and your washing will
not dry properly.
Drying has been interrupted as a result of a power cut, because the
condensate container is full or because the maximum drying time has
been exceeded.
ʠ
Drying time too long. Rinse the fluff filters under running water a Page 4.
Insufficient supply of air a ensure that air can circulate.
Air inlet possibly blocked a Clear inlet a Page 8.
Ambient temperature higher than 35 °C a ventilate the room. The
optimum ambient temperature for drying is between 5 °C and 35 °C.
Outside of this range, the drying time may increase.
ʠ
The humidity in the room
increases significantly.
Make sure the room is sufficiently ventilated.
ʠ
Power failure. Remove laundry from the dryer immediately and spread out.
This allows the heat to dissipate. Be careful as the door, the drum
and the laundry may be hot.
ʠ
One or more indicator lights
for programme status are
flashing.
Clean filter and air cooler a Page 4/6.
Check installation conditions a Page 8.
Switch off, leave to cool down, switch on again, restart programme.
11

Safety instructions

EmergencyPull the appliance plug out of the socket immediately or disconnect the fuse.ONLY use the dryer...in rooms inside the house.to dry fabrics. The dryer must NEVER...be used for other purposes than those described above.be modified in terms of its technology or attributes.DangersThe dryer must not be used by children or persons who have not been instructed in its use.Do not leave children unsupervised near the dryer.Keep pets away from the dryer.Remove all objects from pockets. Make especially sure that cigarette lighters are removed as they constitute an a explosion hazard.
Do not lean or sit on the door a risk of tipping.
Installation
Secure loose cables a tripping hazard.
Do not operate the dryer if there is a risk of frost.Mains connectionConnect the dryer according to specifications to an AC earthed socket, as otherwise it cannot be guaranteed that the appliance is completely safe.The cable cross-section must be sufficient.Only use earth-leakage circuit breakers with the following symbol: The appliance plug and socket must be compatible.Do not use multiple plugs/couplings and/or extension cables.
Do not hold the appliance plug with wet hands a risk of electric shock.
Never pull the appliance plug out of the socket by its cable.
Do not damage the mains lead a risk of electric shock.
Operation
Only load the drum with laundry. Check the contents before you switch the dryer
on.
Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease or paint (e.g. hair setting spray, nail polish remover, stain remover, cleaning solvent, etc.) a fire/explosion hazard.The tumble dryer is not to be used if industrial chemicals have been used for cleaning.
Dust (e.g. coal dust, flour) poses a danger: do not use the dryeraexplosion
hazard.Do not turn off the dryer until the drying process ends, unless the laundry will be removed quickly and spread out, so that the heat can dissipate.Do not put laundry containing foamed material/rubber in the dryer a elastic material may be destroyed and the dryer may be damaged due to possible deformation of the foamed material.Light things, such as long hair, may be sucked into the air inlet of the dryer a risk of injury.Final part of a tumble dryer cycle occurs without heat (cool down cycle), to ensure that the items are left at a temperature that ensures that the items will not be damaged.Switch off the dryer once the programme has ended.The exterior of the appliance's rear panel becomes very hot during operation. Never touch the hot surface of the appliance's rear panel.
Keep children away from the appliance a risk of burns.
Condensation is not drinking water and may be contaminated with fluff.DefectDo not use the dryer if it is defective or if you suspect it is.Repairs must only be carried out by the after-sales service.Do not use the dryer if the mains cable is defective. To avoid danger, only have the defective mains cable replaced by the after-sales service.Always pull the mains plug out of the socket before changing the bulb for the interior light a risk of electric shock.Spare partsOnly use genuine spare parts and accessories for safety reasons.Disposal
Dryer: pull out the appliance plug, then cut off the mains cable from the
appliance. Dispose of at municipal waste disposal facility.
Packaging: do not leave children alone with packing partsa risk
of suffocation.All materials are environmentally sound and can be reused. Dispose of in an environmentally-responsible manner.
siemens-home.bsh-group.com/welcomeRegister
your
productonline

Tumble dryer

WT44E107FI
en Operating and installation instructions Observe the safety instructions on page 11!
Read these instructions and the separate Energy-saving mode instructions before switching on the dryer.

View the manual for the Siemens iQ300 WT44E107FI here, for free. This manual comes under the category dryers and has been rated by 22 people with an average of a 8.5. This manual is available in the following languages: English. Do you have a question about the Siemens iQ300 WT44E107FI or do you need help? Ask your question here

Need help?

Do you have a question about the Siemens and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 15
P
Pia andersenFebruary 11, 2020

I have purchased this dryer Siemens iQ300 WT44E107FI with number WT44E107FI/01. And since it is used, I did not receive a manual. Can you send me information about what the different buttons mean? Especially the one that can light up since only one of them lights up.

This message has been automatically translated
C
Carl Johan Hilding October 22, 2020

Hello. Our Siemens iQ300 WT44E107FI dryer is warning that it is full of water even though the container is empty. What could be wrong? Best regards, Carl Johan.

This message has been automatically translated
N
NooshinJanuary 6, 2021

My dryer Siemens iQ300 WT44E107FI has stopped working! It started making a strange sound and after 4-5 cycles it stopped working! And there was also a slight burnt smell...

This message has been automatically translated
T
Tove ThyniJanuary 9, 2021

Why does our dryer stop before the laundry is dry? I have emptied the water container and removed the dust from the collection box.

This message has been automatically translated
V
Vicki Damsgaard SerupMarch 11, 2020

Hello, When I dry duvets or duvet covers, the machine beeps/stops after a short time. The duvet is not dry. I start it again, the machine runs for 2-5 minutes, and then stops again. What is wrong? Best regards, Vicki Serup

This message has been automatically translated
M
Monica Almqvist August 25, 2020

Which program is for down jacket with tennis balls and low temperature?

This message has been automatically translated
M
MariaOctober 6, 2020

how much space if any is required between the top of the machine i.e. Siemens iq300 condenser dryer and the bottom of the worktop?

P
PatrikJuly 31, 2022

The dryer won't start. After selecting a program and pressing Start, it just beeps twice and nothing further happens. No other symbol is shown.

1 comment
P
Pulkit gargSeptember 2, 2022

Did you get any solution

C
CliveSeptember 18, 2023

Hi, when I turn in my iQ300 dryer it beeps three times but no lights come on and it won’t start. When I turn it on, there is F:08 on the hr/min display. Any help would be appreciated. Thanks Clive

The Siemens iQ300 WT44E107FI is a freestanding dryer with a condensation drying system. Its door hinge is located on the right, and it features button and rotary controls for easy operation. The built-in LED display provides clear information about the drying process. The dryer comes with a cord length of 1.45 meters, allowing for flexible placement in your home. With a rated capacity of 7 kilograms, it can handle a moderate amount of laundry in a single drying cycle. It has been classified as a B-grade drying class, indicating its efficiency in removing moisture from clothes. The cycle time of the Siemens iQ300 WT44E107FI is 120 minutes, providing sufficient time for thorough drying. The noise level while operating is measured at 66 decibels, which may be considered moderate. One of the key features of this dryer is its anti-crease function, which helps to reduce wrinkles in clothes. It also includes a dedicated anti-crease cycle that lasts for 120 minutes, ensuring that your garments come out looking neat and tidy. In summary, the Siemens iQ300 WT44E107FI is a feature-packed dryer that offers convenience and efficiency. With its condensation drying system, button and rotary controls, LED display, and anti-crease function, it provides a reliable and effective solution for drying your laundry.

General
BrandSiemens
ModeliQ300 WT44E107FI | WT44E107FI
Productdryer
EAN4242003800973
LanguageEnglish
FiletypeUser manual (PDF)
Design
Appliance placementFreestanding
Loading typeFront-load
Drying systemCondensation
Product colorWhite
Door hingeRight
Control typeButtons, Rotary
Built-in displayYes
Display typeLED
Cord length1.45 m
Drum materialGalvalume
Drum volume112 L
Performance
Drum capacity7 kg
Drying classB
Cycle time120 min
Noise level66 dB
Anti-Crease functionYes
Anti-Crease cycle120 min
Ergonomics
Delayed start timerNo
Drum interior lightNo
LED program stage indicatorYes
Child lock-
Power
Energy efficiency classB
Connected load2800 W
AC input voltage220 - 240 V
AC input frequency50 Hz
Heat sourceElectric
Annual energy consumption497 kWh
Power consumption (off)0.1 W
Power consumption (standby)1 W
Current16 A
Weight & dimensions
Width598 mm
Depth601 mm
Height842 mm
Weight38002 g
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Siemens iQ300 WT44E107FI below.

What is a condenser dryer?

A condenser dryer is a dryer in which condensation ends up in a reservoir.

What is a drain dryer?

A drain dryer is a dryer in which the warm air and condensation are drained through a hose.

What is the best thing to do about a smelly dryer?

It is best to wipe the dryer drum with a damp cloth and some lemon cleaner.

There is a burning smell from my dryer, now what?

Check the following: - That the fluff filter is clean. - That the bottom of the dryer is free of dust. - That the drain hose is clean. If the above does not help, a mechanic should be called in.

What is the weight of the Siemens iQ300 WT44E107FI?

The Siemens iQ300 WT44E107FI has a weight of 38002 g.

What is the height of the Siemens iQ300 WT44E107FI?

The Siemens iQ300 WT44E107FI has a height of 842 mm.

What is the width of the Siemens iQ300 WT44E107FI?

The Siemens iQ300 WT44E107FI has a width of 598 mm.

What is the depth of the Siemens iQ300 WT44E107FI?

The Siemens iQ300 WT44E107FI has a depth of 601 mm.

What energy label does the Siemens iQ300 WT44E107FI have?

The Siemens iQ300 WT44E107FI has energy label B.

How do I properly clean the lint filter of the Siemens iQ300 WT44E107FI dryer?

Regularly remove the lint filter located just inside the dryer door and clear away any lint buildup. This step ensures efficient airflow and prevents potential fire hazards.

Why is my Siemens iQ300 WT44E107FI dryer not starting?

Check if the dryer door is firmly closed and the power cord is securely plugged into a working outlet. Additionally, ensure that the program selector is set to the desired drying cycle and that the Start/Stop button is pressed to initiate the drying process.

What should I do if my dryer is taking longer than usual to dry clothes?

First, confirm that the lint filter is clean and the dryer is not overloaded. Additionally, check the ventilation system to ensure proper airflow and remove any blockages. If the issue persists, consider adjusting the drying program or contacting a professional technician for further assistance.

How can I adjust the drying time for specific loads on the Siemens iQ300 WT44E107FI dryer?

Utilize the machine's customizable drying programs by selecting the desired program and then pressing the Time Dry button to adjust the drying time manually. This option allows you to tailor the drying process to meet your specific needs.

Is it safe to dry delicate fabrics in the Siemens iQ300 WT44E107FI dryer?

Yes, it is safe to dry delicate fabrics using this dryer. Simply utilize the appropriate drying program designed for delicate materials, such as Low Heat, to ensure gentle drying without causing damage. Always refer to the garment care label for specific instructions when drying delicate fabrics.

Does the Siemens iQ300 WT44E107FI have a built-in display?

Yes, the Siemens iQ300 WT44E107FI has a built-in display. This means that the user can easily see and control the settings of the dryer.

What is the rated capacity of the Siemens iQ300 WT44E107FI?

The rated capacity of the Siemens iQ300 WT44E107FI is 7 kg. This is a decent capacity for a dryer and can accommodate a good amount of laundry.

Does the Siemens iQ300 WT44E107FI have an Anti-Crease function?

Yes, the Siemens iQ300 WT44E107FI has an Anti-Crease function. This means that it will keep the clothes rotating periodically after the drying cycle is finished to prevent creasing.

Is the noise level of the Siemens iQ300 WT44E107FI high?

Yes, the noise level of the Siemens iQ300 WT44E107FI is 66 dB. This is considered to be a relatively high noise level for a dryer.

Does the Siemens iQ300 WT44E107FI have a Delayed start timer?

No, the Siemens iQ300 WT44E107FI does not have a Delayed start timer. This means that the user cannot program the dryer to start at a later time.

Is the manual of the Siemens iQ300 WT44E107FI available in English?

Yes, the manual of the Siemens iQ300 WT44E107FI is available in English .

Is your question not listed? Ask your question here

No results