Siemens iQ300 WT43N200 manual

Siemens iQ300 WT43N200
8 · 14
PDF manual
 · 40 pages
English
manualSiemens iQ300 WT43N200
Faults and what to do about them en
33

3 Faults and what to do about them

Faults and what to do about them
Faults Cause/remedy
Ì on the display panel
and drying has been
interrupted.
Empty the condensate container and press the Start button ~ Page 24.
If the optional condensation drain is installed, the drain hose may be
blocked. Check the hose for deposits and flush the hose out.
¥ on the display panel. Clean the fluff filter and/or the heat exchanger, then select the Start button
~ Page 27;~ Page 31.
Dryer does not start. Mains plug plugged in or fuse checked?
program selected? Select a program.
Dryer door open? Close the door.
Childproof lock activated? Deactivate the childproof lock.
"Finish in" time selected? program starts after a delay.
Display panel goes off
and Start button flashes.
Not a fault. Energy saving mode is active ~ Page 13.
Creasing. Creasing occurs when you have exceeded the maximum load or selected
the wrong program for the type of fabric. All the required information can
be found in the program table.
Remove clothes immediately after drying; creasing may occur if they are
left in the drum.
Water is leaking out. Not a fault; the dryer may be positioned on an incline. Level the dryer.
Change in the pro-
gramme duration dis-
played during drying.
Not a fault. The moisture sensors detect the remaining moisture in the load and
adjust the programme length (except timed programmes).
Laundry is not dried cor-
rectly or is still too damp.
After the end of the program, warm laundry feels damper than it actually is.
Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but does not
increase the temperature. Your laundry will become drier ~ Page 24.
Select a program with a longer drying time or increase the drying level. This
does not increase the temperature.
Select a timed program for subsequent drying of laundry that is still damp
~ Page 22.
If you have exceeded the maximum load for the program, the laundry may
not be dried properly.
Clean the moisture sensor in the drum. The sensor may become covered by
a fine layer of limescale or residues of detergents and care products which
then impair its function. Your laundry is not being dried correctly
~ Page 32.
Drying has been interrupted as a result of a power cut, because the conden-
sate container is full or because the maximum drying time has been
exceeded.
Note: See also the laundry tips ~ Page 21.
* depending on the model

View the manual for the Siemens iQ300 WT43N200 here, for free. This manual comes under the category dryers and has been rated by 14 people with an average of a 8. This manual is available in the following languages: English. Do you have a question about the Siemens iQ300 WT43N200 or do you need help? Ask your question here

Need help?

Do you have a question about the Siemens and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 6
H
HieleSeptember 28, 2020

How can you turn off the beeping sound on the WT43RV00 iq300 dryer?

This message has been automatically translated
Y
Yvonne SchaffelhuberMarch 2, 2018

How can I turn off the signal tone?

This message has been automatically translated
N
Nicole HeckerJanuary 8, 2020

How do I remove the child lock?

This message has been automatically translated
M
Mary-LouMarch 10, 2024

How do I continue to dry clothes which are still damp

D
Denise MolloyDecember 10, 2023

What setting will give me a drying temperature of 65 please

A
Anne Lise Munson JohansenNovember 11, 2020

Cleaning out the condensate container

The Siemens iQ300 WT43N200 is a freestanding dryer with a width of 598 millimeters, a depth of 599 millimeters, and a height of 842 millimeters. Weighing 39000 grams, it is designed to be placed in any suitable spot in the household. The energy efficiency class of this dryer is B, and it has an annual energy consumption of 496 kilowatt-hours, qualifying it as an average energy-saving device. The drying class is also marked as B, indicating a moderate drying performance. With a rated capacity of 7 kilograms, this Siemens iQ300 model can handle a considerable amount of laundry in each cycle. Equipped with a connected load of 2800 watts and an AC input frequency of 50 Hz, it operates effectively to dry clothes efficiently. In terms of noise, the Siemens iQ300 WT43N200 has a level of 65 decibels, which is comparable to conversational speech. This ensures relatively quiet operation while the dryer is in use. Overall, the Siemens iQ300 WT43N200 offers a practical solution for drying clothes with its moderate energy efficiency and capacity. Its compact dimensions and sturdy construction make it suitable for everyday use. However, it is important to consider your specific needs and requirements when choosing a dryer, as individual preferences may vary.

General
BrandSiemens
ModeliQ300 WT43N200 | WT43N200
Productdryer
EAN4242003755327
LanguageEnglish
FiletypeUser manual (PDF)
Design
Appliance placementFreestanding
Loading typeFront-load
Drying systemHeat pump
Product colorWhite
Built-in displayYes
Display typeLED
Drum materialGalvalume
Cord length1.45 m
Control typeRotary, Touch
Drum volume112 L
Power
Energy efficiency classB
Annual energy consumption496 kWh
Heat source-
Connected load2800 W
AC input voltage220 - 240 V
AC input frequency50 Hz
Energy consumption4.08 kWh
Power consumption (off)0.1 W
Power consumption (standby)0.5 W
Performance
Drying classB
Noise level65 dB
Drum capacity7 kg
Cycle time111 min
Anti-Crease functionYes
Anti-Crease cycle120 min
Auto, Wool, Mix, Quick
Weight & dimensions
Width598 mm
Depth599 mm
Height842 mm
Weight39000 g
Ergonomics
Delayed start timerYes
Child lockYes
Drum interior lightNo
BuzzerYes
Remaining time indicationYes
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Siemens iQ300 WT43N200 below.

What is a condenser dryer?

A condenser dryer is a dryer in which condensation ends up in a reservoir.

What is a drain dryer?

A drain dryer is a dryer in which the warm air and condensation are drained through a hose.

What is the best thing to do about a smelly dryer?

It is best to wipe the dryer drum with a damp cloth and some lemon cleaner.

There is a burning smell from my dryer, now what?

Check the following: - That the fluff filter is clean. - That the bottom of the dryer is free of dust. - That the drain hose is clean. If the above does not help, a mechanic should be called in.

What is the weight of the Siemens iQ300 WT43N200?

The Siemens iQ300 WT43N200 has a weight of 39000 g.

What is the height of the Siemens iQ300 WT43N200?

The Siemens iQ300 WT43N200 has a height of 842 mm.

What is the width of the Siemens iQ300 WT43N200?

The Siemens iQ300 WT43N200 has a width of 598 mm.

What is the depth of the Siemens iQ300 WT43N200?

The Siemens iQ300 WT43N200 has a depth of 599 mm.

What energy label does the Siemens iQ300 WT43N200 have?

The Siemens iQ300 WT43N200 has energy label B.

Why is my Siemens iQ300 dryer not turning on?

Make sure the power cord is securely plugged into a functioning electrical outlet and check the circuit breaker to ensure it hasn't tripped. Additionally, ensure that the door is closed properly, as the dryer will not start if the door is ajar.

How can I select the appropriate drying program on my Siemens iQ300 WT43N200?

Rotate the program selector dial to choose the desired drying program. Refer to the label next to each program on the control panel for guidance on the type of garments or fabrics suitable for each specific program.

My clothes are not drying properly. Any suggestions?

First, ensure that the lint filter is clean, as a clogged filter can impede proper drying. Additionally, check if the selected drying program matches the type and thickness of the garments you are drying. If needed, select a higher temperature or longer drying time for bulkier items.

How do I prevent wrinkling of clothes in the dryer?

After the drying cycle is complete, promptly remove your garments from the drum to minimize wrinkling. Once removed, you can either fold them right away or hang them up to prevent further creasing.

Is there a way to reduce the noise level of my Siemens iQ300 dryer?

To reduce noise, ensure that the dryer is installed on a stable, even surface to minimize vibrations. Additionally, ensure the load inside the drum is balanced and not overloaded, as an unbalanced load can cause excessive noise.

Does the Siemens iQ300 WT43N200 have a freestanding placement?

Yes, the Siemens iQ300 WT43N200 has a freestanding placement. This means that it can be placed anywhere in your home without the need for built-in installation.

What is the annual energy consumption of the Siemens iQ300 WT43N200?

The annual energy consumption of the Siemens iQ300 WT43N200 is 496 kWh. This is an indicator of how much energy the dryer will consume over the course of a year.

What is the drying class of the Siemens iQ300 WT43N200?

The drying class of the Siemens iQ300 WT43N200 is B. This means that it has a moderate drying performance compared to other dryers on the market.

What is the noise level of the Siemens iQ300 WT43N200?

The noise level of the Siemens iQ300 WT43N200 is 65 dB. This is a fairly standard noise level for dryers and may be noticeable in a quiet room.

What is the rated capacity of the Siemens iQ300 WT43N200?

The rated capacity of the Siemens iQ300 WT43N200 is 7 kg. This means that it can accommodate up to 7 kilograms of laundry per load, making it suitable for medium-sized households.

Is the manual of the Siemens iQ300 WT43N200 available in English?

Yes, the manual of the Siemens iQ300 WT43N200 is available in English .

Is your question not listed? Ask your question here

No results