Shure ANI4OUT manual

Shure ANI4OUT
8.6 · 1
PDF manual
 · 23 pages
English
manualShure ANI4OUT
Shure Incorporated
16/23
1.
2.
Log Details
Description
Provides details on events and errors, including IP address and subnet mask.
Time Stamp
Power cycles:days:hours:minutes:seconds since most recent boot-up.
Event ID
Indicates event type for internal reference.
Tip: Use the filter to narrow down results. Select a category heading to sort the log.

Levels and Metering

Adjusting Input levels

Check the source level before it reaches the Network Interface:
Verify that the networked microphones or other Dante sources are operating at nominal output levels.
Levels for Microflex Advance
microphones are adjustable through their web application.
Adjust the digital gain in the Network Interface web application:
Use the faders or manually enter a gain value.
The digital gain adjusts the level of the signal before it reaches the analog circuitry.
Set these levels as high as possible without reaching the peak level (0 dB) on the meter.

Adjusting Output Levels

Access the analog output levels through the web application, by selecting an output level from the Analog Gain (dB) pull-down
menu. Match the output level from the Network Interface to the input sensitivity on the analog device:
Line level (0 dB)
Aux level (-20 dB)
Microphone level (-46 dB)

LED Signal and Clipping Indicators

Each analog output channel has a corresponding LED:
Green: Audio signal present
Red: Audio signal is clipping and should be attenuated.
Note: the meters in the web application are not affected by the Analog Gain (dB) setting.

Pre- and Post-Fader Metering

There are two modes for monitoring so that both the input and output signals can be monitored separately.
When set to pre-fader, the meter displays the signal level from the source on the Dante network. If signals are too low or clip
ping, adjust them at the source.
When set to post-fader, the meter is affected by the digital gain. It is not affected by the output analog gain setting.

Manual

View the manual for the Shure ANI4OUT here, for free. This manual comes under the category hand blenders and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Shure ANI4OUT or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Shure and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Shure ANI4OUT specifications

Below you will find the product specifications and the manual specifications of the Shure ANI4OUT.

General
BrandShure
ModelANI4OUT | ANI4OUT-XLR
Producthand blender
EAN0042406475457
LanguageEnglish
FiletypeUser manual (PDF), Datasheet (PDF)
Audio
Frequency range20 - 20000 Hz
Dynamic range117 dB
Total Harmonic Distortion (THD) + noise0.05 %
Channels quantity4 channels
Balanced line output level20 dB
Power
Power consumption (typical)10 W
External power supplyYes
Operational conditions
Operating temperature (T-T)-6.7 - 40 °C
Storage temperature (T-T)-29 - 74 °C
Network
Ethernet LANYes
Design
Product colorBlack
Ports & interfaces
Ethernet LAN (RJ-45) ports1
XLR inputs4
Weight & dimensions
Width140 mm
Depth128 mm
Height40 mm
Weight663 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Shure ANI4OUT below.

What is the weight of the Shure ANI4OUT?

The Shure ANI4OUT has a weight of 663 g.

What is the height of the Shure ANI4OUT?

The Shure ANI4OUT has a height of 40 mm.

What is the width of the Shure ANI4OUT?

The Shure ANI4OUT has a width of 140 mm.

What is the depth of the Shure ANI4OUT?

The Shure ANI4OUT has a depth of 128 mm.

Is the manual of the Shure ANI4OUT available in English?

Yes, the manual of the Shure ANI4OUT is available in English .

Is your question not listed? Ask your question here

No results