Sharp PN-R903A manual

Sharp PN-R903A
6.6 · 1
PDF manual
 · 62 pages
English
manualSharp PN-R903A
6
E
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam. Do not use in an environment where
there are corrosive gases (sulfur dioxide, hydrogen sulde,
nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this
could lead to re.
- Ensure that the monitor does not come into contact with
water or other uids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to re or
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of re.
- Do not use the monitor in places where it may be exposed to
direct sunlight. Risk of cabinet deformation and failure if the
monitor is used in direct sunlight.
- Please be sure to constantly remove dust and garbage that
has attached to the ventilation opening.
If dust collects in the ventilation opening, it may lead to
excessive heat, outbreak of re, or malfunction.
- As a standard, clean the inside of the monitor once every
year. If dust collects inside the monitor, it may lead to
excessive heat, outbreak of re, or malfunction. Please
request a cleaning of the inside of the monitor from an
authorized SHARP servicing dealer or service center.
- Images cannot be rotated on this monitor.
When using in portrait orientation, you will need to prepare
appropriately orientated content in advance.
- The AC outlet shall be installed near the equipment and shall
be easily accessible.

The Power Cord

- Use only the power cord supplied with the monitor.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in re or electric shock.
- Do not use the power cord with a power tap.
Adding an extension cord may lead to re as a result of
overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.

Manual Scope

- Microsoft and Windows are either registered trademarks or
trademarks of Microsoft Corporation in the United States
and/or other countries.
- The terms HDMI and HDMI High-Denition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing Administrator, Inc. in the
United States and other countries.
- DisplayPort is a registered trademark of Video Electronics
Standards Association.
- Adobe, Acrobat, and Acrobat Reader are either registered
trademarks or trademarks of Adobe Systems Incorporated in
the United States and/or other countries.
- This product comes with RICOH Bitmap Fonts produced and
sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
- This manual assumes use in landscape orientation, except
where specically noted.

LED Backlight

The LED backlight in this product has a limited lifetime.
* If the screen gets dark or does not turn on, it may be
necessary to replace the LED backlight.
* This LED backlight is exclusive to this product and must
be replaced by an authorized SHARP servicing dealer
or service center. Please contact an authorized SHARP
servicing dealer or service center for assistance.
Fan
The fan in this product has a limited lifetime.
Please contact an authorized SHARP servicing dealer or
service center for assistance with fan replacement.

TIPS AND SAFETY INSTRUCTIONS

Manual

View the manual for the Sharp PN-R903A here, for free. This manual comes under the category monitors and has been rated by 1 people with an average of a 6.6. This manual is available in the following languages: English. Do you have a question about the Sharp PN-R903A or do you need help? Ask your question here

Need help?

Do you have a question about the Sharp and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Sharp PN-R903A specifications

Below you will find the product specifications and the manual specifications of the Sharp PN-R903A.

General
BrandSharp
ModelPN-R903A | PN-R903A
Productmonitor
EAN4974019771762, 4974019916002, 0074000066595
LanguageEnglish
FiletypeUser manual (PDF)
Display
Display diagonal90 "
Display resolution1920 x 1080 pixels
Display technologyLED
HD typeFull HD
Panel typeUV2A
Display number of colors1.06 billion colors
Pixel pitch1.038 x 1.038 mm
Display brightness700 cd/m²
Contrast ratio (typical)4000:1
Response time6 ms
Viewing angle, horizontal176 °
Viewing angle, vertical176 °
Active display area (W x H)1992 x 1120 mm
Panel life- h
TouchscreenNo
Other features
Power managementYes
Plug and PlayYes
Ports & interfaces
Ethernet LANYes
DisplayPorts quantity1
DVI portYes
DVI-I ports quantity1
VGA (D-Sub) input ports1
HDMI ports quantity2
RS-232CYes
DVI-D ports quantity1
PC Audio inYes
USB portNo
Performance
Analog signal format systemNTSC, NTSC 3.58, NTSC 4.43, PAL, PAL 60, SECAM
HDCPYes
PurposeUniversal
TV tuner integratedNo
Audio
Built-in speaker(s)Yes
Number of built-in speakers2
Design
VESA mountingYes
Product colorBlack
Product designDigital signage flat panel
Panel mounting interface600 x 400,600 x 600 mm
Placement supportedIndoor
Power
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (typical)660 W
Power consumption (standby)- W
Operational conditions
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)20 - 80 %
Computer system
Computer systemNo
Weight & dimensions
Width2054 mm
Depth122 mm
Height1196 mm
Weight74978 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Sharp PN-R903A below.

What screen dimensions does my monitor have?

The size of your monitor is usually expressed in inches, 1 inch is 2.54 centimetres. The size is the diagonal size of your monitor, so you measure the screen from bottom left to top right.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

What is the weight of the Sharp PN-R903A?

The Sharp PN-R903A has a weight of 74978 g.

What is the screen size of the Sharp PN-R903A?

The screen size of the Sharp PN-R903A is 90 ".

What is the height of the Sharp PN-R903A?

The Sharp PN-R903A has a height of 1196 mm.

What is the screen resolution of the display of the Sharp PN-R903A?

The screen resolution of the Sharp PN-R903A is 1920 x 1080 pixels.

What is the width of the Sharp PN-R903A?

The Sharp PN-R903A has a width of 2054 mm.

What is the depth of the Sharp PN-R903A?

The Sharp PN-R903A has a depth of 122 mm.

Does the Sharp PN-R903A have a display resolution of 1920 x 1080 pixels?

Yes, the Sharp PN-R903A has a display resolution of 1920 x 1080 pixels. This means users can expect sharp and clear images on the 90" screen.

Is the display technology of the Sharp PN-R903A LED?

Yes, the Sharp PN-R903A uses LED technology, which typically provides energy-efficient performance and vibrant colors.

What is the display brightness of the Sharp PN-R903A?

The Sharp PN-R903A has a display brightness of 700 cd/m², which is considered quite high compared to other monitors, ensuring a bright and vivid viewing experience.

What is the typical contrast ratio of the Sharp PN-R903A?

The Sharp PN-R903A has a contrast ratio of 4000:1, which indicates good differentiation between dark and light colors on the screen.

Does the Sharp PN-R903A come with Ethernet LAN connectivity?

Yes, the Sharp PN-R903A is equipped with Ethernet LAN connectivity, allowing for easy network connection and access to online content or resources.

How can I troubleshoot issues with selecting the display method (PIP/PbyP) on the Sharp PN-R903A monitor?

To troubleshoot issues with selecting the display method (PIP/PbyP) on the Sharp PN-R903A monitor, follow these steps: 1. Access the MULTI/PIP menu on the monitor. 2. Navigate to the PIP/PbyP settings within the menu. 3. Select the desired display method: PIP, PbyP, or PbyP2. 4. Adjust the PIP size, horizontal position (H-POS), vertical position (V-POS), and blending as needed. 5. Choose the input signal source for the sub screen in PIP mode. 6. Set the sound output for the main and sub screens in PIP, PbyP, or PbyP2 mode. 7. Configure the position of the main screen in PbyP or PbyP2 mode. 8. Set the display method for when no signals are input in PIP, PbyP, or PbyP2 mode to either MANUAL or AUTO. These steps should help you troubleshoot and customize the display method on your Sharp PN-R903A monitor.

How can I adjust the date and time settings on the Sharp PN-R903A monitor?

To adjust the date and time settings on the Sharp PN-R903A monitor, follow these steps: 1. Press the up or down arrow buttons to select the date and time on the date/time setting screen. 2. Use the left or right arrow buttons to change the numerical values for the date and time. 3. Press the ENTER button to confirm the date and time settings. 4. Ensure that the date is set in "Month/Day/Year" order and the time is set on a 12-hour basis. 5. Note that the clock is maintained by the internal battery. 6. If the date/time setting screen appears when turning on the monitor, the internal battery may need replacement after about 5 years. 7. Contact an authorized SHARP servicing dealer for assistance with battery replacement if needed.

How can I troubleshoot issues with the enlarge function on the Sharp PN-R903A monitor?

To troubleshoot issues with the enlarge function on the Sharp PN-R903A monitor, follow these steps: 1. Ensure that the "Enlarge" setting is turned on in the MULTI menu. 2. Select "ADVANCED (ENLARGE)" in the menu. 3. Set the number of monitors aligned horizontally and vertically in the ENLARGE H and ENLARGE V settings. 4. Configure the section of the separated image to be displayed on each monitor in the ENLARGE-POS setting by selecting the position using the navigation buttons. 5. If black bands appear around the screen when connecting a laptop computer with specific resolutions, enable the ZOOM2 SPECIAL SETTING in the OTHERS menu and select ZOOM2 in the SIZE setting to display the area inside the black band. These steps should help you troubleshoot any issues with the enlarge function on your Sharp PN-R903A monitor.

How can I troubleshoot issues with the sound output settings in PIP/PbyP modes on the monitor?

To troubleshoot sound output settings in PIP/PbyP modes on the Sharp PN-R903A monitor, follow these steps: 1. Access the "MULTI/PIP" menu on the monitor. 2. Navigate to the "SOUND CHANGE" option in the menu. 3. Adjust the sound settings to specify the sound output for PIP, PbyP, or PbyP2 modes. 4. Ensure that the main screen sound is output correctly, even when specifying sound for the sub screen. 5. If needed, adjust the position of the main screen in PbyP or PbyP2 mode using the "MAIN POS" setting. 6. Similarly, adjust the position of the sub screen in PbyP2 mode using the "PbyP2 POS" setting. 7. Check the "AUTO OFF" setting to determine the display method when no signals are input for the sub screen in PIP, PbyP, or PbyP2 modes. These steps will help you troubleshoot and optimize the sound output settings in PIP/PbyP modes on your Sharp PN-R903A monitor.

Is the manual of the Sharp PN-R903A available in English?

Yes, the manual of the Sharp PN-R903A is available in English .

Is your question not listed? Ask your question here

No results