Sharp PN-R903A manual

Sharp PN-R903A
6.6 · 1
PDF manual
 · 62 pages
English
manualSharp PN-R903A
36
E

Controlling the Monitor with a PC (RS-232C)

n

Repeater control

This system has a function to allow setting of multiple
monitors connected in a daisy chain using a single command.
This function is called repeater control. You can use Repeater
control function without assigning ID numbers.
[E
xamp
l
e
]
Set 1
Set 2 Set
3S
et 4
* If monitors are connected as shown above, you can
execute a command like “Set all monitors’ input settings to
D-SUB[RGB]”.
n

Repeater control command

Repeater control is achieved by setting the FOURTH
CHARACTER of the parameter to “+”.
Example:
VOLM030 +
Sets volume of all monitors to 30.
In repeater control, responses are returned by all the
connected monitors.
If you want to determine that a value has been returned by a
specic set, assign ID numbers to each monitor in advance.
When some monitors do not return their responses, the
probable cause is that the monitors could not receive the
command or command processing is not complete. Do not
send a new command.
Example: (When 4 monitors are connected, and
assigned ID numbers: 1 through 4)
VOLM030 +
WAIT
OK
001
OK
002
OK
003
OK
004 If 4 monitors are connected in
a chain, reliable operation can
be ensured by sending a new
command only after a reply
has been returned by 4th (last)
monitor.
Repeater control can also be used for reading settings.
Example:
VOLM ? ? ? +
WAIT
10
001
Volume settings for all
monitors are returned.
20
002
30
003
30
004
TIPS
If repeater control is used during ID designation (IDSL,
IDLK), the ID designation is canceled.

Setting of the GAMMA user data

n

To transfer the GAMMA user data

Use the user data transfer commands (UGRW, UGGW and
UGBW). For each of the R, G and B colors, divide the total
512 pieces of user data into 16 blocks, and transfer 32 pieces
of data with each command.
C1 C2 C3 C4 P1 P2 P3 P4
S1 S2
Command field
Block number (01 to 16)
Data fieldChecksum field
Example: To transfer the data of block 1 (0 to 31 levels)
of red (R) data
UGRW01000000010002 … 0031C0
Command
Block number
32 pieces of data Checksum
One piece of data consists
of 4 digits.
* If data is less than 4 digits, add a “0” (zero) to make it 4
digits.
* The checksum eld is the character string (ASCII) data of
lower-order one byte which indicates the sum of the block
number and 32 pieces of data in hexadecimal (0 to F).
n

Saving the GAMMA user data

Use the user data save command (UGSV) to save the
transferred user data in the monitor.
If the data is not saved, it will be cleared when:
The main power switch is off
POWER SAVE MODE is ON and the monitor enters
standby mode
n

Activating the GAMMA user data

To activate the transferred user data, select USER for GAMMA
of the PICTURE menu, or send the corresponding RS-232C
command.
n

Checking the GAMMA user data

Use the user data read commands (UGRR, UGGR and
UGBR) to return 512 pieces of user data for each of the R,
G and B colors. Divide the data into 16 blocks and return 32
pieces of data with each command. The value to be returned
is not the value stored in the monitor, but the value in the
temporary memory for display. (These values are the same
when the user data save command (UGSV) above has been
sent.)
TIPS
The user data is not initialized by RESET of the PICTURE
menu. To initialize the user data, use ALL RESET of the
FUNCTION menu.
The GAMMA user data initialize command (UGRS) allows
the initialization of the user data only.

Manual

View the manual for the Sharp PN-R903A here, for free. This manual comes under the category monitors and has been rated by 1 people with an average of a 6.6. This manual is available in the following languages: English. Do you have a question about the Sharp PN-R903A or do you need help? Ask your question here

Need help?

Do you have a question about the Sharp and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Sharp PN-R903A specifications

Below you will find the product specifications and the manual specifications of the Sharp PN-R903A.

General
BrandSharp
ModelPN-R903A | PN-R903A
Productmonitor
EAN4974019771762, 4974019916002, 0074000066595
LanguageEnglish
FiletypeUser manual (PDF)
Display
Display diagonal90 "
Display resolution1920 x 1080 pixels
Display technologyLED
HD typeFull HD
Panel typeUV2A
Display number of colors1.06 billion colors
Pixel pitch1.038 x 1.038 mm
Display brightness700 cd/m²
Contrast ratio (typical)4000:1
Response time6 ms
Viewing angle, horizontal176 °
Viewing angle, vertical176 °
Active display area (W x H)1992 x 1120 mm
Panel life- h
TouchscreenNo
Other features
Power managementYes
Plug and PlayYes
Ports & interfaces
Ethernet LANYes
DisplayPorts quantity1
DVI portYes
DVI-I ports quantity1
VGA (D-Sub) input ports1
HDMI ports quantity2
RS-232CYes
DVI-D ports quantity1
PC Audio inYes
USB portNo
Performance
Analog signal format systemNTSC, NTSC 3.58, NTSC 4.43, PAL, PAL 60, SECAM
HDCPYes
PurposeUniversal
TV tuner integratedNo
Audio
Built-in speaker(s)Yes
Number of built-in speakers2
Design
VESA mountingYes
Product colorBlack
Product designDigital signage flat panel
Panel mounting interface600 x 400,600 x 600 mm
Placement supportedIndoor
Power
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (typical)660 W
Power consumption (standby)- W
Operational conditions
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)20 - 80 %
Computer system
Computer systemNo
Weight & dimensions
Width2054 mm
Depth122 mm
Height1196 mm
Weight74978 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Sharp PN-R903A below.

What screen dimensions does my monitor have?

The size of your monitor is usually expressed in inches, 1 inch is 2.54 centimetres. The size is the diagonal size of your monitor, so you measure the screen from bottom left to top right.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

What is the weight of the Sharp PN-R903A?

The Sharp PN-R903A has a weight of 74978 g.

What is the screen size of the Sharp PN-R903A?

The screen size of the Sharp PN-R903A is 90 ".

What is the height of the Sharp PN-R903A?

The Sharp PN-R903A has a height of 1196 mm.

What is the screen resolution of the display of the Sharp PN-R903A?

The screen resolution of the Sharp PN-R903A is 1920 x 1080 pixels.

What is the width of the Sharp PN-R903A?

The Sharp PN-R903A has a width of 2054 mm.

What is the depth of the Sharp PN-R903A?

The Sharp PN-R903A has a depth of 122 mm.

Does the Sharp PN-R903A have a display resolution of 1920 x 1080 pixels?

Yes, the Sharp PN-R903A has a display resolution of 1920 x 1080 pixels. This means users can expect sharp and clear images on the 90" screen.

Is the display technology of the Sharp PN-R903A LED?

Yes, the Sharp PN-R903A uses LED technology, which typically provides energy-efficient performance and vibrant colors.

What is the display brightness of the Sharp PN-R903A?

The Sharp PN-R903A has a display brightness of 700 cd/m², which is considered quite high compared to other monitors, ensuring a bright and vivid viewing experience.

What is the typical contrast ratio of the Sharp PN-R903A?

The Sharp PN-R903A has a contrast ratio of 4000:1, which indicates good differentiation between dark and light colors on the screen.

Does the Sharp PN-R903A come with Ethernet LAN connectivity?

Yes, the Sharp PN-R903A is equipped with Ethernet LAN connectivity, allowing for easy network connection and access to online content or resources.

How can I troubleshoot issues with selecting the display method (PIP/PbyP) on the Sharp PN-R903A monitor?

To troubleshoot issues with selecting the display method (PIP/PbyP) on the Sharp PN-R903A monitor, follow these steps: 1. Access the MULTI/PIP menu on the monitor. 2. Navigate to the PIP/PbyP settings within the menu. 3. Select the desired display method: PIP, PbyP, or PbyP2. 4. Adjust the PIP size, horizontal position (H-POS), vertical position (V-POS), and blending as needed. 5. Choose the input signal source for the sub screen in PIP mode. 6. Set the sound output for the main and sub screens in PIP, PbyP, or PbyP2 mode. 7. Configure the position of the main screen in PbyP or PbyP2 mode. 8. Set the display method for when no signals are input in PIP, PbyP, or PbyP2 mode to either MANUAL or AUTO. These steps should help you troubleshoot and customize the display method on your Sharp PN-R903A monitor.

How can I adjust the date and time settings on the Sharp PN-R903A monitor?

To adjust the date and time settings on the Sharp PN-R903A monitor, follow these steps: 1. Press the up or down arrow buttons to select the date and time on the date/time setting screen. 2. Use the left or right arrow buttons to change the numerical values for the date and time. 3. Press the ENTER button to confirm the date and time settings. 4. Ensure that the date is set in "Month/Day/Year" order and the time is set on a 12-hour basis. 5. Note that the clock is maintained by the internal battery. 6. If the date/time setting screen appears when turning on the monitor, the internal battery may need replacement after about 5 years. 7. Contact an authorized SHARP servicing dealer for assistance with battery replacement if needed.

How can I troubleshoot issues with the enlarge function on the Sharp PN-R903A monitor?

To troubleshoot issues with the enlarge function on the Sharp PN-R903A monitor, follow these steps: 1. Ensure that the "Enlarge" setting is turned on in the MULTI menu. 2. Select "ADVANCED (ENLARGE)" in the menu. 3. Set the number of monitors aligned horizontally and vertically in the ENLARGE H and ENLARGE V settings. 4. Configure the section of the separated image to be displayed on each monitor in the ENLARGE-POS setting by selecting the position using the navigation buttons. 5. If black bands appear around the screen when connecting a laptop computer with specific resolutions, enable the ZOOM2 SPECIAL SETTING in the OTHERS menu and select ZOOM2 in the SIZE setting to display the area inside the black band. These steps should help you troubleshoot any issues with the enlarge function on your Sharp PN-R903A monitor.

How can I troubleshoot issues with the sound output settings in PIP/PbyP modes on the monitor?

To troubleshoot sound output settings in PIP/PbyP modes on the Sharp PN-R903A monitor, follow these steps: 1. Access the "MULTI/PIP" menu on the monitor. 2. Navigate to the "SOUND CHANGE" option in the menu. 3. Adjust the sound settings to specify the sound output for PIP, PbyP, or PbyP2 modes. 4. Ensure that the main screen sound is output correctly, even when specifying sound for the sub screen. 5. If needed, adjust the position of the main screen in PbyP or PbyP2 mode using the "MAIN POS" setting. 6. Similarly, adjust the position of the sub screen in PbyP2 mode using the "PbyP2 POS" setting. 7. Check the "AUTO OFF" setting to determine the display method when no signals are input for the sub screen in PIP, PbyP, or PbyP2 modes. These steps will help you troubleshoot and optimize the sound output settings in PIP/PbyP modes on your Sharp PN-R903A monitor.

Is the manual of the Sharp PN-R903A available in English?

Yes, the manual of the Sharp PN-R903A is available in English .

Is your question not listed? Ask your question here

No results