Sharp PN-R903A manual

Sharp PN-R903A
6.6 · 1
PDF manual
 · 62 pages
English
manualSharp PN-R903A
32
E
You can return the settings to their factory-preset values and
restrict operations.
1. Hold
SIZE
down until “F” appears in the upper left
corner of the screen.
2. While “F” appears, press
, , , in that
order.
▲▲▲▲▲
OFF
UNLOCKED
ON 1
ON
LED
OFF
MONITOR
FUNCTION
ALL RESET
ADJUSTMENT LOCK
ADJUSTMENT LOCK TARGET
RS-232C/LAN
OSD DISPLAY
LED
TEMPERATURE ALERT
STATUS ALERT
POWER BUTTON
CONTROLLER INPUT
OK…[ENTER] END…[RETURN]
3. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
Press
ENTER
, select the resetting method, and then press
ENTER
.
After initialization, turn the main power switch off and
then back on.
ALL RESET1 ....Resets all the settings to the factory
default settings.
ALL RESET2 ....Returns all settings to the factory default
settings except for the following items:
LAN SETUP, RS-232C/LAN SELECT,
ID No. SET, BAUD RATE, NETWORK,
MAIL, SERVICE & SUPPORT, and
SNMP (See page 25, and pages 49 to
52.)
ADJUSTMENT LOCK
You can disable operations on the monitor and the
remote control unit that use buttons.
OFF ...Enables operation.
ON 1 ..Disables all operations other than turning power
on/off and FUNCTION.
ON 2 ..Only the FUNCTION operation is enabled.
Disables all operations other than FUNCTION (not
even power on/off).
ADJUSTMENT LOCK TARGET
Sets the target to prohibit operation of with
ADJUSTMENT LOCK.
REMOTE CONTROL ..... Prohibits remote control
operation
MONITOR BUTTONS ... Prohibits monitor switch
operation
BOTH ............................. Prohibits remote control and
monitor switch operation
RS-232C/LAN
Species whether to allow control via RS-232C or LAN
(see pages 33 and 45).

Initialization (Reset)/Functional Restriction Setting (FUNCTION)

OSD DISPLAY
Shows/hides the menu, modes and messages.
The FUNCTION screen cannot be hidden.
ON 1 .............. Shows all menus, modes and messages.
ON 2 .............. Hides messages automatically displayed
by the display. Shows messages during
operation.
OFF ............... Hides all menus, modes and messages.
LED
Species whether to light the power LED.
TEMPERATURE ALERT
Selects the notication method for an abnormal
temperature.
OFF .............. Do not notify about an abnormal
temperature.
OSD & LED .. When an abnormal temperature is
detected, the power LED ashes in red
and green alternately and the screen
displays a message: TEMPERATURE.
LED............... When an abnormal temperature is
detected, the power LED ashes in red
and green alternately.
STATUS ALERT
Selects the notication method for a hardware error.
OFF .............. Do not notify about the error.
OSD & LED .. When a hardware error is detected, the
power LED ashes in red and the screen
displays a message: STATUS [xxxx].
LED............... When a hardware error is detected, the
power LED ashes in red.
POWER BUTTON
Normally, leave this setting as MONITOR.
When using an optional part, if instruction appears,
change the setting accordingly.
CONTROLLER INPUT
Normally, you do not need to change this setting.
When using an optional part, if instruction appears,
change the setting accordingly.
4. Press
RETURN
to return to the normal screen.
TIPS
When both abnormal temperature and hardware error are
detected, the hardware error notication overrides.
If TEMPERATURE ALERT or STATUS ALERT is set to
OSD&LED, alert messages will appear even if the OSD
DISPLAY is set to ON 2 or OFF.
If TEMPERATURE ALERT or STATUS ALERT is set to LED
or OSD & LED, the LED lights even if the LED function is
set to OFF.

Manual

View the manual for the Sharp PN-R903A here, for free. This manual comes under the category monitors and has been rated by 1 people with an average of a 6.6. This manual is available in the following languages: English. Do you have a question about the Sharp PN-R903A or do you need help? Ask your question here

Need help?

Do you have a question about the Sharp and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Sharp PN-R903A specifications

Below you will find the product specifications and the manual specifications of the Sharp PN-R903A.

General
BrandSharp
ModelPN-R903A | PN-R903A
Productmonitor
EAN4974019771762, 4974019916002, 0074000066595
LanguageEnglish
FiletypeUser manual (PDF)
Display
Display diagonal90 "
Display resolution1920 x 1080 pixels
Display technologyLED
HD typeFull HD
Panel typeUV2A
Display number of colors1.06 billion colors
Pixel pitch1.038 x 1.038 mm
Display brightness700 cd/m²
Contrast ratio (typical)4000:1
Response time6 ms
Viewing angle, horizontal176 °
Viewing angle, vertical176 °
Active display area (W x H)1992 x 1120 mm
Panel life- h
TouchscreenNo
Other features
Power managementYes
Plug and PlayYes
Ports & interfaces
Ethernet LANYes
DisplayPorts quantity1
DVI portYes
DVI-I ports quantity1
VGA (D-Sub) input ports1
HDMI ports quantity2
RS-232CYes
DVI-D ports quantity1
PC Audio inYes
USB portNo
Performance
Analog signal format systemNTSC, NTSC 3.58, NTSC 4.43, PAL, PAL 60, SECAM
HDCPYes
PurposeUniversal
TV tuner integratedNo
Audio
Built-in speaker(s)Yes
Number of built-in speakers2
Design
VESA mountingYes
Product colorBlack
Product designDigital signage flat panel
Panel mounting interface600 x 400,600 x 600 mm
Placement supportedIndoor
Power
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (typical)660 W
Power consumption (standby)- W
Operational conditions
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)20 - 80 %
Computer system
Computer systemNo
Weight & dimensions
Width2054 mm
Depth122 mm
Height1196 mm
Weight74978 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Sharp PN-R903A below.

What screen dimensions does my monitor have?

The size of your monitor is usually expressed in inches, 1 inch is 2.54 centimetres. The size is the diagonal size of your monitor, so you measure the screen from bottom left to top right.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

What is the weight of the Sharp PN-R903A?

The Sharp PN-R903A has a weight of 74978 g.

What is the screen size of the Sharp PN-R903A?

The screen size of the Sharp PN-R903A is 90 ".

What is the height of the Sharp PN-R903A?

The Sharp PN-R903A has a height of 1196 mm.

What is the screen resolution of the display of the Sharp PN-R903A?

The screen resolution of the Sharp PN-R903A is 1920 x 1080 pixels.

What is the width of the Sharp PN-R903A?

The Sharp PN-R903A has a width of 2054 mm.

What is the depth of the Sharp PN-R903A?

The Sharp PN-R903A has a depth of 122 mm.

Does the Sharp PN-R903A have a display resolution of 1920 x 1080 pixels?

Yes, the Sharp PN-R903A has a display resolution of 1920 x 1080 pixels. This means users can expect sharp and clear images on the 90" screen.

Is the display technology of the Sharp PN-R903A LED?

Yes, the Sharp PN-R903A uses LED technology, which typically provides energy-efficient performance and vibrant colors.

What is the display brightness of the Sharp PN-R903A?

The Sharp PN-R903A has a display brightness of 700 cd/m², which is considered quite high compared to other monitors, ensuring a bright and vivid viewing experience.

What is the typical contrast ratio of the Sharp PN-R903A?

The Sharp PN-R903A has a contrast ratio of 4000:1, which indicates good differentiation between dark and light colors on the screen.

Does the Sharp PN-R903A come with Ethernet LAN connectivity?

Yes, the Sharp PN-R903A is equipped with Ethernet LAN connectivity, allowing for easy network connection and access to online content or resources.

How can I troubleshoot issues with selecting the display method (PIP/PbyP) on the Sharp PN-R903A monitor?

To troubleshoot issues with selecting the display method (PIP/PbyP) on the Sharp PN-R903A monitor, follow these steps: 1. Access the MULTI/PIP menu on the monitor. 2. Navigate to the PIP/PbyP settings within the menu. 3. Select the desired display method: PIP, PbyP, or PbyP2. 4. Adjust the PIP size, horizontal position (H-POS), vertical position (V-POS), and blending as needed. 5. Choose the input signal source for the sub screen in PIP mode. 6. Set the sound output for the main and sub screens in PIP, PbyP, or PbyP2 mode. 7. Configure the position of the main screen in PbyP or PbyP2 mode. 8. Set the display method for when no signals are input in PIP, PbyP, or PbyP2 mode to either MANUAL or AUTO. These steps should help you troubleshoot and customize the display method on your Sharp PN-R903A monitor.

How can I adjust the date and time settings on the Sharp PN-R903A monitor?

To adjust the date and time settings on the Sharp PN-R903A monitor, follow these steps: 1. Press the up or down arrow buttons to select the date and time on the date/time setting screen. 2. Use the left or right arrow buttons to change the numerical values for the date and time. 3. Press the ENTER button to confirm the date and time settings. 4. Ensure that the date is set in "Month/Day/Year" order and the time is set on a 12-hour basis. 5. Note that the clock is maintained by the internal battery. 6. If the date/time setting screen appears when turning on the monitor, the internal battery may need replacement after about 5 years. 7. Contact an authorized SHARP servicing dealer for assistance with battery replacement if needed.

How can I troubleshoot issues with the enlarge function on the Sharp PN-R903A monitor?

To troubleshoot issues with the enlarge function on the Sharp PN-R903A monitor, follow these steps: 1. Ensure that the "Enlarge" setting is turned on in the MULTI menu. 2. Select "ADVANCED (ENLARGE)" in the menu. 3. Set the number of monitors aligned horizontally and vertically in the ENLARGE H and ENLARGE V settings. 4. Configure the section of the separated image to be displayed on each monitor in the ENLARGE-POS setting by selecting the position using the navigation buttons. 5. If black bands appear around the screen when connecting a laptop computer with specific resolutions, enable the ZOOM2 SPECIAL SETTING in the OTHERS menu and select ZOOM2 in the SIZE setting to display the area inside the black band. These steps should help you troubleshoot any issues with the enlarge function on your Sharp PN-R903A monitor.

How can I troubleshoot issues with the sound output settings in PIP/PbyP modes on the monitor?

To troubleshoot sound output settings in PIP/PbyP modes on the Sharp PN-R903A monitor, follow these steps: 1. Access the "MULTI/PIP" menu on the monitor. 2. Navigate to the "SOUND CHANGE" option in the menu. 3. Adjust the sound settings to specify the sound output for PIP, PbyP, or PbyP2 modes. 4. Ensure that the main screen sound is output correctly, even when specifying sound for the sub screen. 5. If needed, adjust the position of the main screen in PbyP or PbyP2 mode using the "MAIN POS" setting. 6. Similarly, adjust the position of the sub screen in PbyP2 mode using the "PbyP2 POS" setting. 7. Check the "AUTO OFF" setting to determine the display method when no signals are input for the sub screen in PIP, PbyP, or PbyP2 modes. These steps will help you troubleshoot and optimize the sound output settings in PIP/PbyP modes on your Sharp PN-R903A monitor.

Is the manual of the Sharp PN-R903A available in English?

Yes, the manual of the Sharp PN-R903A is available in English .

Is your question not listed? Ask your question here

No results