Schwinn 700IC manual

Schwinn 700IC
7.5 · 1
PDF manual
 · 68 pages
English
manualSchwinn 700IC

Schwinn

IC3 / IC7 / 700IC Bikes

Service Manual

8018628.080123.E

Service Manual

Section Code Section Page Number
1 Important Safety Instructions 2
1 Safety Warning Labels and Serial Number 3
1 Reading the Serial Number 3
 6SHFL¿FDWLRQV
1 Maintenance 4
1 Leveling the Machine 5
1 Moving/Storing the Machine 5
1 Troubleshooting 6
1 Changing Unit Measures 7
1 Maintenance Parts Exploded View 8
1 Replacement Procedure Skill Level 9
Mechanical Procedures 10
2 Brake Lubrication 10
3 Brake Adjustment 13
4 Belt Tension Adjustment 15
Part Replacement 19
5 Pedals 19
6 Console 22
7 Handlebars and Handlebar Post 24
8 Fender 27
9 Brake Pad Assembly and Brake/Resistance Knob Assembly 29
10 Crank Arm 32
11 Drive Belt Cover 36
12 Flywheel Tensioners 39
13 Drive Belt 43
14 Flywheel Assembly 49
15 Speed Sensor 55
16 Crank Axle Wave Washer 61
17 Drive Pulley 64

Table of Contents

Nautilus, Inc., www.NautilusInc.com, 5415 Centerpoint Parkway, Groveport, OH 43125 U.S.A. - Customer Service: North America (800) 605-3369, csnls@nautilus.com | outside U.S.
www.nautilusinternational.com | © 2018 Nautilus, Inc. | Schwinn and the Schwinn Quality logo are trademarks owned by or licensed to Nautilus,Inc., which are registered or otherwise
protected by common law in the United States and other countries. Polar® is a trademark of its owner. | ORIGINAL DOCUMENT - ENGLISH VERSION ONLY
8018887.080123.E

View the manual for the Schwinn 700IC here, for free. This manual comes under the category bicycle trainers and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Schwinn 700IC or do you need help? Ask your question here

Need help?

Do you have a question about the Schwinn and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Schwinn 700IC is a bicycle trainer that is designed for indoor use. It provides users with a convenient way to continue their cycling training regimen regardless of the weather conditions outside. The 700IC features a sturdy construction that ensures stability during use, allowing cyclists to focus on their training without any distractions. It is equipped with a high-quality flywheel that provides a smooth and consistent riding experience, simulating the feel of riding on the road. This bicycle trainer is designed to be adjustable, offering riders the ability to customize their workout to their specific needs. The height and handlebar position can be easily adjusted to provide a comfortable and ergonomic riding position. The saddle is also adjustable, allowing users to find the perfect fit for their body type. The 700IC features a compact and space-saving design, making it suitable for use in small apartments or homes with limited space. It is also equipped with transport wheels, making it easy to move and store when not in use. This bicycle trainer is compatible with various cycling apps and virtual training platforms, allowing users to track their performance and join virtual cycling classes. It also features a built-in media rack, providing a convenient spot to place a smartphone or tablet for entertainment during workouts. Overall, the Schwinn 700IC is a reliable and durable bicycle trainer that offers adjustable features and compatibility with virtual training platforms, providing users with a convenient and effective indoor cycling experience.

General
BrandSchwinn
Model700IC
Productbicycle trainer
LanguageEnglish
FiletypeUser manual (PDF), Instructions / Assembly (PDF), Quickstart Guide (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Schwinn 700IC below.

How much should I exercise as an adult per week?

As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.

What is an adult's maximum heart rate?

As a rule of thumb for your maximum heart rate, you can use 220 minus your age.

How do I troubleshoot if the Schwinn 700IC bicycle trainer does not turn on?

To troubleshoot if the Schwinn 700IC bicycle trainer does not turn on, follow these steps: 1. Check the power source: Ensure that the bicycle trainer is properly plugged into a working power outlet. Verify that the power cord is securely connected to the trainer. 2. Check the power switch: Make sure that the power switch on the bicycle trainer is in the "on" position. If it is already on, try turning it off and then back on again. 3. Check the batteries: If the bicycle trainer has a battery compartment, check if the batteries are inserted correctly and if they have enough charge. Replace the batteries if necessary. 4. Reset the console: If the trainer has a console, try resetting it by pressing the reset button or following the instructions in the manual. 5. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact Schwinn customer service for further assistance. They can provide specific troubleshooting steps or arrange for repairs if needed. Remember to always refer to the Schwinn 700IC bicycle trainer manual for detailed instructions and safety precautions.

What should I do if I encounter an error message on the Schwinn 700IC bicycle trainer display?

To troubleshoot if you encounter an error message on the Schwinn 700IC bicycle trainer display, follow these steps: 1. Check the error message: Read the error message displayed on the console carefully. Take note of any specific codes or instructions provided. 2. Power cycle the trainer: Turn off the bicycle trainer and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again. This can help reset the system and clear temporary errors. 3. Check the connections: Ensure that all cables and connections between the console and the trainer are secure and properly connected. If any cables appear damaged or loose, try reconnecting or replacing them. 4. Perform a software update: If the error message persists, check if there is a software update available for the Schwinn 700IC. Follow the instructions in the manual to download and install the update, if applicable. 5. Contact customer support: If the error message continues to appear after following the above steps, it is recommended to contact Schwinn customer service for further assistance. They can provide specific troubleshooting steps or arrange for repairs if needed. Remember to always refer to the Schwinn 700IC bicycle trainer manual for detailed instructions and safety precautions.

How can I troubleshoot if the resistance levels are not working properly on the Schwinn 700IC bicycle trainer?

To troubleshoot if the resistance levels are not working properly on the Schwinn 700IC bicycle trainer, follow these steps: 1. Check the resistance knob: Ensure that the resistance knob is properly tightened and not loose. If it is loose, tighten it clockwise to increase the resistance. 2. Inspect the resistance assembly: Remove the acorn nut and hex nut at the end of the resistance knob rod. Check for any damage or wear on the resistance knob assembly. If any parts are damaged, they may need to be replaced. 3. Replace the resistance knob assembly: If the resistance knob assembly is damaged, follow the instructions in the assembly manual to replace it. Carefully install the new resistance knob assembly, making sure to thread it through the square spacer and secure it with the hex nut and acorn nut. 4. Install the new brake assembly: After replacing the resistance knob assembly, install the new brake assembly according to the instructions in the manual. 5. Adjust the resistance knob: Once the new assembly is installed, adjust the resistance knob as necessary to achieve the desired resistance level. 6. Perform a final inspection: Inspect the entire machine to ensure that all hardware is tight and components are properly assembled. Refer to the owner's manual for specific instructions on the final inspection. If the issue persists after following these steps, it is recommended to contact Schwinn customer service for further assistance.

What should I check if the pedals of the Schwinn 700IC bicycle trainer are making a clicking noise?

To troubleshoot if the pedals of the Schwinn 700IC bicycle trainer are making a clicking noise, follow these steps: 1. Check the pedal installation: Ensure that the pedals are securely and properly installed on the crank arms. Use a pedal wrench to tighten the pedals clockwise. Make sure they are not loose or wobbling. 2. Inspect the pedal threads: Examine the threads on the pedals and crank arms for any damage or wear. If the threads are damaged, the pedals may need to be replaced. 3. Lubricate the pedal threads: Apply a small amount of bicycle-specific grease or lubricant to the pedal threads. This can help reduce friction and eliminate clicking noises caused by dry or worn threads. 4. Check the pedal bearings: If the clicking noise persists, the pedal bearings may be worn or damaged. In this case, it is recommended to contact Schwinn customer service for further assistance. They can provide specific troubleshooting steps or arrange for repairs if needed. Remember to always refer to the Schwinn 700IC bicycle trainer manual for detailed instructions and safety precautions.

How do I troubleshoot if the heart rate monitor is not syncing with the Schwinn 700IC bicycle trainer?

To troubleshoot if the heart rate monitor is not syncing with the Schwinn 700IC bicycle trainer, follow these steps: 1. Check the data cable integrity: Ensure that all wires in the data cable are intact. If any wires are cut or crimped, replace the cable. 2. Check the data cable connections/orientation: Make sure the data cable is securely connected to both the console and the main frame assembly. Ensure that the small latch on the connector is aligned and snapped into place. 3. Check the batteries: Verify that the batteries in the console are installed correctly. If they are correctly installed, replace them with a fresh set of new batteries. 4. Check the speed sensor magnet position: Ensure that the speed sensor magnet is properly in place on the flywheel. 5. Check the speed sensor assembly: Verify that the speed sensor assembly is aligned with the magnet and connected to the data cable. Realign the sensor if necessary. Replace the sensor if there is any damage to it or the connecting wire. If the issue persists after following these steps, it is recommended to contact Schwinn customer care for further assistance. Please note that the heart rate monitor function is an approximation and should be used for reference only.

Is the manual of the Schwinn 700IC available in English?

Yes, the manual of the Schwinn 700IC is available in English .

Is your question not listed? Ask your question here

No results