Sanoxy WAP-300 manual

Sanoxy WAP-300
7.8 · 1
PDF manual
 · 2 pages
English
manualSanoxy WAP-300

WiFi REPEATER

REV.1.1
A4. Open web browser and type
http://192.168.10.1 in the browser's
address box. This number is the
default IP address for this device.
A5. The login screen below will
appear. Enter the “User Name” and
“Password” and click “OK” to login.
The default User name is “admin
and the Password is “admin”.
A6. After logging in and click “Setup Wizard”, you will see the web page below:
Select “Wireless Repeater Mode (Station)” and click on ‘Next to continue.
Wireless-N Wifi Repeater
04
Wireless-N Wifi Repeater
03
Wireless-N Wifi Repeater
02
You can configure the Wi-Fi Repeater by connecting it with your computer/laptop with enclosed RJ45 cable or wirelessly. We recommend you to do it with wire.A2. Click the “Start” button (it should be located at the lower-left corner of your screen), then click Control Panel”. Click “View Network Status and Tasks”, and then click Manage Network Connections”. Right-click “Local Area Network”, then select “Properties”. When the Local Area Connection Propertieswindow appears, select “Internet Protocol Version 4 (TCP/IPv4)” and then click “Properties”.
A1. Plug the Wi-Fi Repeater to a
wall socket. Connect your computer
/ laptop with the Wi-Fi Repeater with
enclosed RJ45 Cable.
A3. Setting IP address manually: Type IP address is 192.168.10.x (x is from 2 to 254), and Subnet mask is 255.255.255.0. Type the Router’s LAN IP address (the default IP is 192.168.10.1) into the Default gateway field.
How to configure the Wi-Fi RepeaterA. Configure the Wi-Fi Repeater with RJ45 Cable
For a typical wireless setup at home (as shown below), please do the
following:
You will need WiFi
AP/Router Internet access
You will need broadband
Router Internet access
Connect the WiFi-Repeater
to your Router/Switch with
RJ-45 Cable
Setting up a Wireless Infrastructure Network
Wireless Repeater ModeGetting StartedWireless AP ModeWireless-N Wifi Repeater
01
The WiFi Repeater is a combined wired/wireless network connection device
designed specifically for small business, office, and home office networking
requirements. It allows a wireless network to be expanded using multiple access
points without the need for a wired backbone to link them. It also works well with
other 11b/g and 11n protocol wireless products.
NOTE: If you need to reset the Wi-Fi Repeater, you need press and hold the
reset button inside the tiny hole for 10 seconds.
Before you starting to use this router, please check if there's anything missing in
the package, and contact your dealer of purchase to claim for missing items:
·1 x Wireless-N Repeater
·1 x RJ-45 Networking Cable
·1 x Quick installation Guide
IntroductionPackage ContentsA7. Click on ‘Repeater – OneKey Setting’ buttonA8. Wait a few seconds and you will see the site below and please click on Wireless Network Selection’ button.Wireless-N Wifi Repeater
05
A9. Click on ‘Refresh List’ button. Select the Wireless SSID and click ‘Next’ to continue.
A10.When you see the site below, please do not change any setting but only
insert the password of your network.
Click on ‘Apply and Reboot’ button.
Wireless-N Wifi Repeater
06
A11. Click ‘OK’ to confirm. The Repeater will restart.
A12. Wait a few seconds and you will see the status site like below. It means your Wi-Fi Repeater is ready for use.
The Wi-Fi Repeater1 WLAN key is same with your router.
If you do not see the site like above, you need to re-configure it again.
NOTE: If you need to reset the Wi-Fi Repeater, you need press the reset button
inside the tiny hole for 10 seconds.
Wireless-N Wifi Repeater
07

Wireless-N

展开尺寸:360 x 240 m m

成品尺寸:120 x 90 m m

Manual

View the manual for the Sanoxy WAP-300 here, for free. This manual comes under the category Wifi repeaters and has been rated by 1 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Sanoxy WAP-300 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Sanoxy WAP-300 and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Sanoxy WAP-300 owners to provide you with a good answer.

Number of questions: 0

Sanoxy WAP-300 specifications

Below you will find the product specifications and the manual specifications of the Sanoxy WAP-300.

General
Brand Sanoxy
Model WAP-300 | WAP-300
Product Wifi repeater
EAN 609224104015, 816473012453, 0609224104015, 0816473012453
Language English
Filetype Usermanual (PDF)
Data transmission
Maximum data transfer rate 150 Mbit/s
Supported data transfer rates 11 Mbps, 54 Mbps, 150 Mbps
Antenna
Antenna design Integrated
Wireless LAN features
Modulation 16-QAM,64-QAM,BPSK,CCK,DBPSK,DQPSK,DSSS,OFDM,QPSK
Frequency band 2.4 GHz
Channels quantity 14 channels
Ports & interfaces
Interface RJ 45
Connectivity technology Wireless
Ethernet LAN (RJ-45) ports 1
Certificates
Certification Wi-Fi, RoHS, CE Mark (Europe), FCC (USA)
Security
Security algorithms 128-bit WEP,64-bit WEP,TKIP,WPA,WPA-PSK,WPA2,WPA2-PSK
null
System requirements
Compatible operating systems Linux, Linux Kernel 3.0.8, Linux 2.6.18-2.6.38, Microsoft Windows, Windows ME, Windows 98SE, Windows Vista 32/64 bit, Windows XP 32/64 bit, Windows 2000 32/64 bit, Mac OS, Mac OS 10.8, Mac OS 10.7, Mac OS 10.6, Mac OS 10.5, Mac OS 10.4
Features
LED indicators
Operational conditions
Operating temperature (T-T) 0 - 40 °C
Operating relative humidity (H-H) 10 - 90 %
Storage relative humidity (H-H) 5 - 95 %
Weight & dimensions
Dimensions (WxDxH) 101.6 x 203.2 x 254 mm
Weight 454 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Sanoxy WAP-300 below.

Is your question not listed? Ask your question here

No results