Samsung SHS-H505 manual

Samsung SHS-H505
(3)
  • Number of pages: 2
  • Filetype: PDF

SHS-H505

www.sds.samsun g.com
GC68-02070A ED:02

64&3."/6"-

Convenient Opening- User friendly access with cards and passwordGraphic Interface- Shows the operation status of the doorlockDouble Authorization- Requires card & password combination to openDouble Locking- Prevents opening from outside (Do not disturb)Built-in Fire Detection- Generates alarm in case of a fireSecurity Function- Prevents intrusion from the outside
Direct registration of
Card or key tag
Card or user password
with ID number (01~30)
InitializationRegistrationDeletionOther function
Use index number
All user password/card
5S
4560852580Password
New Password
ID Number
Changing password
CARD
Card or key tag
3S
Password
ID Number
88
CARD
Double Authorization
ON
ON
OFF
OFF
7
9
4
6
Multi-leveled Security Code
CARD
12
1110
9
8
7
6
5
4
3
This section contains important information to ensure the user’s safety and prevent potential damage to property. Please, read this section carefully and use the product accordingly.Warning
The product components used may vary depending on the installation
environment.
2

Safety Cautions

Product Components

• The user shall not install or repair the product without authorization.• Do not install the product in the place where the gap between the door and the frame is 5mm or more.• Make sure that no unauthorized person has the access to the password.• Do not operate the product with wet hands, and keep liquids such as water or drinks away from the product, or the product may malfunction or be damaged.• Do not use the excessive force or sharp objects to push the lockbuttons, as this can damage the product.• Make sure that the door is completely closed when going outside. The manufacturer does not assume the responsibility for any harm caused by engagement of the lock on an improperly closed door.• Please do not hang on the product or pull it.• Be sure to correctly match the poles (+/-) when installing the batteries. Install the batteries with the correct poles (+/-).• Replace all batteries immediately after they run out of power, and never mix new batteries with used ones.• Do not use water, benzene or alcohol when cleaning the product, as these fluids can cause product malfunction.• Replace the batteries within 1 week after the battery replacement alarm sounds.

Mortise

Replacing the Batteries

If the melody of “Blues for Elise” sounds when opening the door with the password or a card (key tag), it is time to replace the batteries.(The low battery indicator is lighted when the melody sounds.)
Battery Replacement Alarm Generation
Replace all 8 batteries within a 1 week of the first alarm sound.
Replacing the Battery
In order to safely use the product, please read “Safety Precautions”. The features of this product and the contents of the user guide may be changed without notice for quality improvement.

Opening the Door from Outside with a Password

Password must be entered after the light is on, and if does not, touch [Number Pad]
and re-enter.
To cancel, press [ ] button and re-enter.
If the password is wrong 5 times,peep warning alarm will sound 20 times and
the system will shut-down for about 3 minutes. When malfunction happens, “beep
will sound every 10 seconds, and stop mode will be turned off automatically after 3
minutes with multiplebeeps’.
Note
When purchased, the product is set to Multi-leveled Security Code Entry
Mode initially. Please refer to “Multi-leveled Security Code Entry Mode
setting” for Common Mode setting.
Silent Mode
Before entering the password, press the [] button and enter the
password, then both the sound of the key entering and the door opening will be suspended. It is a useful function if you do not want to disturb neighbors when you go in and out at night.Touching [Number Pad] will light up the number pad.When two arbitrary buttons are lighted, press the buttons in order.When the numbers on the number pad are lighted, enter the password and press the [] button.
Success:
DING DONG DENG
Fail:
DING DONG DING
DONG
To register multiple cards or key tags, lightly place another card or key tag
to the card reader within 20 seconds after registering the previous card or
key tag.
ID number is given automatically in order of the registration.WarningPlace the card or key tag to be registered on the card reader of the outer body. You will know the card or key tag has been registered when “DING DONG DENG” sounds.Place the registered card or key tag to the card reader on the outer body.
3. Placing the Card or Key Tag on the
Card Reader (from the outside)
DING DONG
DENG
4. Confirming Card or Key Tag
Registration (from the outside)
[Card and Key Tag Registration Without ID number]

Closing the Door from the Inside

Initialization (Password, Card, Key Tag)

All registered data (password, card, key tag) are deleted. After
initialization, the password is set to ‘1234’, and the registered card, key
tag data are erased. Please register a new password after initialization.
1. Pressing the [Register]
Button (from the inside)
2. Entering the Numbers for
Initialization (from the outside)
When the number pad is lighted, enter ‘4560852580’ and then press the [] button.Press and hold the [Register] button for 5 seconds.
DING DONG
DING DING
DING DING
DING DING

Intrusion Detection Function

This function generates the alarm sound when an attempt is made to forcefully open the door from the inside or the outside.(This is a basic function of the lock, and cannot be separately set or released.)If the door is forcefully opened while locked, the door opening sensor detects it and generates the alarm sound.
This function generates the alarm sound when fire is detected so that
the residence can quickly respond. The built-in fire detection function
is a basic function of the lock, and cannot be released by the user.
Fire detection function is operational at about 75 ± 10 ; this can
vary depending on the installation environment.
When fire occurs, the temperature sensor detects it and flashes the [Close] button while generating the alarm sound. The door is automatically opened after the alarm sound has stopped. (The lock resumes normal operation if the inside temperature returns to a normal level.) The built-in fire detection
function is activated when the temperature rises around 60°C, which may
differ depending on the installation environment.

Built-in Fire Detection Function

Outside
Get a registered card authorized or enter the password and then press the [] button.Press the [Register] button.
Inside
Releasing the Alarm
The contents of this user guide are subject to change without prior notice to the user in order to enhance performance of the product.
Item
Specifications
Voltage AA Alkaline 1.5 Batteries (LR6) 4EA or 8EA (6V)
Emergency Power
Source
9V Battery (6LF22) (Separately sold)
Operation Method
Electronic Control Method (Password entry or card or key tag
reading)
Weight
2.6Kg (including both inner and outer bodies)
Product
Dimensions
Outer Body
(including the handle)
81.9 mm(W) x 302.4 mm(H) x 66.1 mm(D)
Inner Body
(including the handle)
79.0 mm(W) × 290.0 mm(H) × 80.3 mm(D)

Product Specifications

Manage your password with care so that unauthorized people will not have
access to it. Regularly changing your password can reduce the risk of it
being leaked.
Warning

Card and Key Tag Registration

Open the battery cover of the inner body and briefly press the [Register] button.
DINGDONG
1. Pressing the [Register]
Button (from the inside)
Enter the current password (‘1234’ after initialization) when the number pad is lighted, and press the [] button.
2. Entering the Current Password
(from the outside)
DING DONG
DENG, DING DING
Up to 30 cards, including the key tag and user password, can be registered.
- If the security mode is changed as ‘common mode’, second step will be skipped.
- Success: DING DONG DENG
- Fail: DING DONG DING DONG

Menu Table

Outer Body Inner Body
Key Tag
Key tail
User Manual
AABatteries (LR6)
Emergency Key(5EA)
Handle Shaft
Handle Shaft Spring
Support Panel and Inner
Body Fastening Bolts
Support Panel and Outer
Body Fastening Bolts
Strike
box
Mortise
(SHS-AML220)
Strike
Mortise
(SHS-AML320)
Strike
Or
Inner Fastening Bolts
Strike Fastening Bolts
Number Pad UnlightedNumber Pad LightedNumber PadCard ReaderReset SwitchOuter Body HandleLED IndicatorExternal Power Port

Outer Body Parts

Emergency Keyhole

Inner Body Parts

Deadbolt
Latch bolt
Open-door sensor
SHS-AML320 SHS-AML220
Opening the Door Using an Emergency Battery
If the batteries are not replaced after their replacement time comes, they
will be completely discharged and the lock will not operate.
Purchase an emergency battery (9V) at the nearest store. - As the alkaline batteries offer longer life, they are recommended over the manganese batteries or rechargeable ones.Place the card or key tag on the card reader, or enter the password, while the 9V battery is connected to the external power port of the outer body.
Or

Using the Emergency Battery

The door can be opened from outside using a card or key tag.
Place the registered card or key tag on the card reader.
Place the card or key tag on the card reader. The door will be opened after 1 second.
CARD

Opening the Door from Outside with a Card or

Key Tag

Success: DING DONG DENG
Fail: DING DONG DING DONG
1. Touch [Number Pad] 2. Placing the Card or Key Tag on the
Card Reader
Touching [Number Pad] will light up the number pad.Battery CoverAuto/ManualLocking SwitchCLOSE ButtonManual Open-and closeLeverSound ControlSwitchInner bodyHandleRegistrationButton

Deleting Registered Cards

You can delete individual or all registered cards.
1. Pressing the [Register]
Button (from the inside)
Press the [Registration] button for 3 seconds.Enter the current password when the number pad is lighted, and press [] button.
2. Entering the Current Password
(from the outside)
DING DONG
DENG, DING DING
DING DONG
DING DING

Multi-leveled Security Code Entry Mode Setting

You can set the security mode suitable for your use when you open the door
using a password.
Briefly press the [Register] button on the inner body.Press the [] button after pressing the[7] or [9] button, and the security modewill be set.
[
7] Button : Multi-leveled
Security Code Entry
Mode
[9] Button : Common Mode
DING DONG
DING DONG
DENG

Sound Setting and Releasing

The sound that is generated when the number buttons are pressed, when the
door is locked or when the locked door is unlocked, can be set according to
the user’s preference. The product is set to generate all sounds at the factory.
[0] : Mute [1] : Normal [2] : Loud
WTXTY
Put the [Sound Control] switch on one of [0], [1], or [2], and close the battery cover.Open the battery cover on the innerbody.

Automatic/Manual Locking Setting

The Automatic Locking mode allows for automatic locking of the door when
it is closed.
Set the [Automatic/Manual Locking] toggle switch of the Inner Body to the ‘A’/‘M’ position.- Automatic: The door is automatically locked 2 seconds after being closed.- Manual: The door does not lock automatically, and [CLOSE] button must be pressed from the inside, touch [Number Pad] to close the door.
If the poles of the batteries are not placed properly, the lock will not operate
normally.
Liquid leaks from batteries can damage the product. Check the batteries
regularly (every 6 months).
After the battery replacement alarm has sounded, password/card information
cannot be registered, changed, deleted, initialized or configured until the
batteries are replaced.
The unit will stop operating suddenly if the batteries are not replaced.
WarningInside : The double locking sound is generated when the [Close] button is pressed.Outside : The double locking sound is generated, the double locking display LED is lighted, and the door cannot be openedwhen touch [number pad], or a card isapplied.
The double locking function prevents opening of a locked door from outside.
Activating Double Locking
Press the [Close] button for 2 seconds or longer from the inside while the door is locked.The double locking function is released when the inner body handle is rotateddownward, or the manual Open/Close lever is rotated to the right or left.
Setting Double Locking Releasing Double Locking
Peep,
Peep
DING DONG
DENG

Setting the Double Locking

Alarm Sound (Prank Prevention Function)

This function generates an alarm sound and deactivates lock operation
when it is improperly handled from the outside.
This alarm will sound if an attempt is made to open the door with an invalid card, or if a wrong password is entered five times in a row.The alarm sound is generated, and the lock is deactivated for 3 minutes. While the door is in this inactive mode, a single “DING” sound is generated every 10 seconds and seven consecutive “DINGS” will sound after 3 minutes. Following this, the lock is released from inactive mode.)

Setting the Security Function

1. When the door is closed [ ] of the outside body’s number pad will light up. 2. Press and hold the [ ] button on the outer body for 3 seconds while the door is locked.After touching the Number Pad, contact a registered card, or enter the password and then press the [] button.
DING DONG
DENG
Or
Setting the Security Function Releasing the Security Function
CARD
The security function is automatically released when the locked door is
opened from outside by entering the registered password or applying the card
or key tag to the card reader.
Note
3. Entering a New Password
(from the outside)
DING DONG
DENG
Enter the new password (4 to 12 digits) and press the [] button.To make sure the password has been properly registered, check the new password and close the door.

Password Change

The password can be 4~12 digits number. Only one password can be
registered.
DING DONG
1. Pressing the [Register] Button
(from the inside)
Press the [Register] button briefly.Enter the current password when the number pad is lighted, and press the [] button.
2. Entering the Current Password
(from the outside)
DING DONG
DENG, DING DING
4. Checking New Password
Operation (from the outside)

Opening the Door from the Inside

Pulling down the Door Lock
Handle
Rotate the manual Open/Close lever to the right or left to lock the door or release the locking.
Rotating the Manual Open/
Close Lever to the Right or Left
Rotate the door lock handle of the inner body downward.
DING DONG
DENG
Closing the Door from the Inside In the Manual Locking Mode
The door is automatically locked 2 seconds after the door is closed.The door is locked when the [Close] button is pressed, or the manual Open/Close lever is rotated.
SHS-AML320 SHS-AML220
User password is only for the user, so other functions such as registering
cards are not available with this password.
One ID has only one password or card. WarningPlace the card or key tag to be registered on the card reader of the outer body. You will know the card or key tag has been registered when “DING DONG DENG” sounds.Place the registered card or key tag to the card reader on the outer body.
4. Placing the Card or Key Tag
on the Card Reader (from the
outside)
DING DONG
DENG
5. Confirming Card or Key Tag
Registration (from the outside)
[Card and user password registration with ID number]
3. Enter 2 digits ID number 4. Enter new user password
DING DING
DING DONG
DENG
Input ID between 01 and 30, and press [].Enter new user password(4 to 12 digits) and press [].
Or
[Deleting Cards]
3. Reading the card to be deleted
If you want to delete all cards data, press [88] + [] after step 2.
DING DONG
DENG
[Deleting ID information]
3. Enter ID number to delete
Enter 2 digits ID number, then the card or user password of it will be deleted.
DING DONG
DENG

Double Authorization Mode Setting

Double authorization mode requires both card and password to open
the door, ensuring more security.
Briefly press the [Register] button on the inner body.Press the [] button after pressing the[4] or [6] button, and the authorizationmode will be set.
[4] Button : Double
authorization mode on
[6] Button : Double
authorization mode off
DING DONG
DING DONG
DENG
The setup of double authorization mode only works when the door is open.
When purchased, the product is not set to double authorization mode initially.
To setup the double authorization mode, more than 1 card must be
registered.
Double authorization mode will automatically be turned off when all cards are
deleted.
Note
Samsung SHS-H505

Need help?

Number of questions: 3

Do you have a question about the Samsung SHS-H505 or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Samsung SHS-H505 owners to properly answer your question.

Andrea • 28-9-2021 No comments

i just changed the batteries of the door this afternoon, but now the LED does not work at all, i cannot see the LED lighting up from outside, and only can open the door via my key card. how do i resolve this issue?

Answer this question
RATHAPHON • 9-5-2021 No comments

The LED indicator of number pad was disappeared. How should I do ?

Answer this question
Fauzi • 13-10-2020 No comments

Why i cannot access my tag/card to open my door? Before this it functioning smoothly.. Suddenly this problem happen.. Please advice, how to solve this problem .. Thanks..

Answer this question

View the manual for the Samsung SHS-H505 here, for free. This manual comes under the category Not categorized and has been rated by 3 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the Samsung SHS-H505 or do you need help? Ask your question here

Samsung SHS-H505 specifications

General
Brand Samsung
Model SHS-H505
Product Not categorized
Language English
Filetype PDF

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Samsung SHS-H505.

Is your question not listed? Ask your question here