View the manual for the Saba LVS13C45GZ17BK here, for free. This manual comes under the category dishwashers and has been rated by 1 people with an average of a 5.1. This manual is available in the following languages: English. Do you have a question about the Saba LVS13C45GZ17BK or do you need help? Ask your question here
Below you will find the product specifications and the manual specifications of the Saba LVS13C45GZ17BK.
| Brand | Saba |
| Model | LVS13C45GZ17BK |
| Product | dishwasher |
| Language | English |
| Filetype | User manual (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Saba LVS13C45GZ17BK below.
In the case of a smelly dishwasher, you can take the following steps: - Clean the filters - Clean the spray arms - Clean the door rubbers - Run a hot wash program - Run an empty machine with a dishwasher cleaner
It is not recommended to rinse dirty dishes before placing them in the dishwasher. For the life cycle of the machine, it is better to put everything dirty in the dishwasher. The grease on the dirty dishes is the lubrication for the pump in the machine.
The average amount used is about 25 grams of dishwashing detergent. It is recommended to follow the advice on the packaging.
Each dishwasher has a separate compartment for softening salt. It opens when you turn the knob on the compartment. The softening salt can then be poured into the compartment by means of a funnel.
Error code E1 on the Saba LVS13C45GZ17BK dishwasher indicates that the door is not closed properly. To resolve this issue, follow these steps: 1. Check the dishwasher door: Make sure that the door is fully closed and latched. Inspect for any obstructions or debris that may be preventing the door from closing properly. 2. Reset the dishwasher: If the door is closed correctly but the error code persists, try resetting the dishwasher. Turn off the dishwasher by pressing the power button or unplugging it from the power source. Wait for a few minutes, then turn it back on. 3. Check the door latch: Inspect the door latch mechanism for any damage or misalignment. If necessary, adjust or replace the door latch to ensure proper closure. 4. Contact customer support: If the error code continues to appear after following the above steps, it is recommended to contact Saba customer support for further assistance. They will be able to provide specific troubleshooting steps or arrange for a technician to inspect and repair the dishwasher if needed. Remember to always refer to the user manual for detailed instructions and safety precautions when troubleshooting errors on your dishwasher.
To view the product fiche for the Saba LVS13C45GZ17BK dishwasher, follow these steps: 1. Open the user manual: Locate the user manual that came with your dishwasher. It contains important information about the appliance's features, specifications, and usage guidelines. 2. Navigate to the product fiche section: In the user manual, look for the section titled "Technical Information" or "Product Fiche." This section provides detailed information about the dishwasher's dimensions, water pressure, power supply, capacity, and other technical specifications. 3. Read the product fiche: Once you have found the product fiche section, carefully read through the information provided. Pay attention to the dishwasher's height, width, depth, water pressure requirements, power supply details, and capacity in terms of place settings. By following these steps, you will be able to access and review the product fiche for the Saba LVS13C45GZ17BK dishwasher. The product fiche contains essential technical information that can help you understand the dishwasher's specifications and ensure its proper usage.
To start a washing program on the Saba LVS13C45GZ17BK dishwasher, follow these steps: 1. Ensure the dishwasher is properly connected to the power supply and the water tap is turned on. 2. Load the dishes into the dishwasher, making sure not to block the spray arms. 3. Add the required amount of detergent into the dispenser according to the recommended quantity mentioned in the washing program chart. 4. Close the dishwasher door securely. 5. Press the power button to turn on the dishwasher. 6. Select the desired washing program by repeatedly pressing the program selection button. The corresponding program indicator light will flash. 7. If you want to delay the start of the washing program, press the delay start button and select the desired delay time using the corresponding button. Once set, the delay time will stop flashing. 8. If you are using a 3-in-1 tablet, press the 3-in-1 button to activate the appropriate program for the tablet. 9. Press the start button to begin the washing program. The dishwasher will start and progress through the selected program. 10. At the end of the program, the dishwasher will emit a buzz and automatically stop. 11. Wait for about 15 minutes before opening the dishwasher door to avoid burns. 12. Unload the clean dishes from the dishwasher. By following these steps, you will be able to start a washing program on the Saba LVS13C45GZ17BK dishwasher.
To activate the delayed start function on the Saba LVS13C45GZ17BK dishwasher, follow these steps: 1. Ensure the dishwasher is properly connected to the power supply and the water tap is turned on. 2. Load the dishes into the dishwasher, making sure not to block the spray arms. 3. Add the required amount of detergent into the dispenser according to the recommended quantity mentioned in the washing program chart. 4. Close the dishwasher door securely. 5. Press the power button to turn on the dishwasher. 6. Select the desired washing program by repeatedly pressing the program selection button. The corresponding program indicator light will flash. 7. Press the delay start button to activate the delayed start function. The delay start indicator light will start flashing. 8. Use the corresponding button to set the desired delay time. Each press of the button will increase the delay time by a specific interval. 9. Once the desired delay time is set, wait for a few seconds until the delay time stops flashing and remains steady. 10. Press the start button to begin the delayed start. The dishwasher will start the selected washing program after the set delay time has elapsed. By following these steps, you will be able to activate the delayed start function on the Saba LVS13C45GZ17BK dishwasher.
To lock the control panel and prevent accidental button presses on the Saba LVS13C45GZ17BK dishwasher, follow these steps: 1. Ensure the dishwasher is turned on and in standby mode. 2. Locate the control panel on the front of the dishwasher. 3. Look for the "Child Lock" button on the control panel. It is usually labeled with a lock symbol. 4. Press and hold the "Child Lock" button for a few seconds until the indicator light for the child lock function turns on. 5. Once the child lock is activated, the control panel buttons will be disabled, and the dishwasher settings cannot be changed. 6. To unlock the control panel, press and hold the "Child Lock" button again for a few seconds until the indicator light turns off. 7. After unlocking the control panel, you can now use the buttons to select washing programs, adjust settings, and start the dishwasher. By following these steps, you will be able to lock the control panel of the Saba LVS13C45GZ17BK dishwasher to prevent accidental button presses. This feature is especially useful to avoid interruptions or changes to the dishwasher settings during a wash cycle.
The installation requirements for the Saba LVS13C45GZ17BK dishwasher are as follows: 1. Grounding: Ensure that the dishwasher is properly grounded. This is important for safety reasons and to prevent damages. 2. Voltage: Check that the voltage stated on the rating label of the dishwasher matches the voltage in your home. 3. Location: The dishwasher can be installed in various locations in your kitchen as long as there is enough space and accessibility to connect it to the water supply, drainage, and electrical supply. 4. Extension Leads: Avoid connecting the dishwasher to an extension lead to prevent potential safety hazards. 5. Water Supply: Connect the dishwasher's water inlet hose to the mains water supply using a 3/4" female connector. Make sure there is a stopcock close by in the pipe. 6. Ventilation: Ensure that the ventilation openings of the dishwasher are not obstructed by a carpet or any other objects. 7. Maximum Capacity: The dishwasher can wash a maximum of 13 place settings. These installation requirements are important to follow to ensure the proper functioning and safety of the Saba LVS13C45GZ17BK dishwasher.
To connect the water inlet hose of the Saba LVS13C45GZ17BK dishwasher to the mains water supply, follow these steps: 1. Ensure that the dishwasher is placed on an even and stable surface. 2. Locate the straight connector of the inlet hose and the water supply. 3. Securely connect the straight connector of the inlet hose to the water supply. Make sure that the washers are securely in place at both ends of the hose. 4. Insert the drain hose into a drainage pipe. Attach the drain hose to the wall using the supplied U-bend fitting. 5. The end of the drain hose should be dropped into a drainage pipe. The height of the drainage pipe should be between 500mm and 1100mm above the base of the dishwasher. 6. Ensure that there is an air gap around the end of the drain hose. The diameter of the drainage pipe should be at least 40mm. 7. Check for any leaks. If leaks are detected, immediately shut off the water supply and check the hose connections. Re-tighten the connections if necessary. By following these steps, you will be able to properly connect the water inlet hose of the Saba LVS13C45GZ17BK dishwasher to the mains water supply.
Yes, the manual of the Saba LVS13C45GZ17BK is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Saba and is the answer not in the manual?
Question and answer
Number of questions: 0