Ruckus Wireless ZoneFlex 7982 manual

Ruckus Wireless ZoneFlex 7982
7.5 · 1
PDF manual
 · 4 pages
manualRuckus Wireless ZoneFlex 7982
Copyright © 2012 Ruckus Wireless, Inc.
Published September 2012, Part Number 800-70362-001 Rev E

ZoneFlex 7982 Dual Band

802.11n Multimedia Wi-Fi

Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions
on how to set up your Ruckus Wireless ZoneFlex Access
Point. After completing the steps described in this Guide,
you will be able to place the Access Point (AP) at your site
and provide wireless network access to users.
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
User Guides and Release Notes are available at
Software Upgrades are available at
Open Source information is available at
Software License and Limited Warranty are available at


ZoneFlex 7982 Access Point
Mounting screws and anchors (2)
T-Bar clips and alignment spacer
Security screw
Regulatory flyer
•This Quick Setup Guide


A computer running Windows 7 (procedures for other OS’s
are similar)
One or more of the following:
A modem (DSL or cable), broadband router, or other
device provided by your Internet Service Provider
that brings Internet access to your site.
A network switch or a DSL/Internet gateway device.
Two Cat 5e Ethernet cables
An AC power adapter (sold separately), or
An 802.3af or 802.3at -compliant Power over Ethernet (PoE)
switch or PoE injector
1 After removing your Ruckus Wireless AP from its pack-
age, place it next to your computer.
2 Using an Ethernet cable, connect your computer’s net-
work port to one of the two ports on the AP.
3 Using an AC adapter (sold separately), connect the AP to
a convenient (and protected) power source.
Alternatively, connect the 10/100/1000 POE port to a
PoE injector or switch for both power and network
4 Verify that the Power LED on the external enclosure is a
steady green.
1 On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as fol-
Start > Control Panel > Network and Sharing Cen-
ter > Change Adapter Settings
2 Edit the TCP/IPv4 address settings as follows:
Local Area Connection > Properties > Internet
Protocol Version 4 (TCP/IPv4) > Properties
The TCP/IPv4 Properties dialog box appears.
3 Select Use the following IP address (if it is not already
selected) and then make the following entries:
IP address: (or any address in the
192.168.0.x network)
Subnet mask:
Default gateway:
Leave the DNS server fields empty.
4 Click OK to save your changes.
Your changes are put into effect immediately.
As specified earlier, the AP should be directly connected to
your computer (through one of the Ethernet ports) and
powered on, ready for setup.
1 On your computer, open a Web browser window.
2 In the browser, type this URL to connect to the AP:

3 Press <Enter> to initiate the connection. When a security
alert dialog box appears, click OK/Yes to proceed.
4 When the Ruckus Wireless Admin login page appears,
enter the following:
Username: super
Password: sp-admin
5 Click Login.
If the AP is deployed with a ZoneDirector, follow the
ZoneDirector Quick Setup Guide and connect the AP to
your local network.
PoE In
DC input
The following procedures assume Windows 7 as the oper-
ating system. Procedures for other OS’s are similar.
Write down all of the currently active settings so you can
restore your computer to its current configuration later
(when this process is complete).


View the manual for the Ruckus Wireless ZoneFlex 7982 here, for free. This manual comes under the category Access points and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Ruckus Wireless ZoneFlex 7982 or do you need help? Ask your question here

Need help?

Do you have a question about the Ruckus Wireless ZoneFlex 7982 and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Ruckus Wireless ZoneFlex 7982 owners to provide you with a good answer.

Number of questions: 0

Ruckus Wireless ZoneFlex 7982 specifications

Below you will find the product specifications and the manual specifications of the Ruckus Wireless ZoneFlex 7982.

Brand Ruckus Wireless
Model ZoneFlex 7982 | 901-7982-US00
Product Access Point
EAN 5054991127265
Language English
Filetype Usermanual (PDF)
Maximum data transfer rate 1000 Mbit/s
Ethernet LAN data rates 10,100,1000 Mbit/s
Wi-Fi data rate (max) 450 Mbit/s
Frequency band 2.4 - 5 GHz
Number of users 500 user(s)
Modulation -
Channels quantity 11 channels
Networking standards IEEE 802.11a,IEEE 802.11b,IEEE 802.11e,IEEE 802.11g,IEEE 802.11i,IEEE 802.11n,IEEE 802.1Q,IEEE 802.1x,IEEE 802.3,IEEE 802.3ab,IEEE 802.3af,IEEE 802.3at,IEEE 802.3u
2.4 GHz
5 GHz
Management protocols SNMP v1, 2, 3
Supported network protocols IPv4, IPv6, L2TP, PPPoE, HTTP/S, Telnet/SSH, FTP, TFTP
Ports & interfaces
DC-in jack
Ethernet LAN (RJ-45) ports 2
Security algorithms 802.1x RADIUS,WEP,WPA-PSK,WPA-TKIP,WPA2-AES
Antenna gain level (max) 3 dBi
Antennas quantity 2
Antenna features Integrated antenna
Power consumption (typical) 7 W
AC input voltage 12 V
Input current 1.5 A
Power over Ethernet (PoE)
Cable lock slot
Product colour White
Cable lock slot type Kensington
Operational conditions
Operating relative humidity (H-H) 0 - 95 %
Operating temperature (T-T) 0 - 50 °C
Weight & dimensions
Width 203 mm
Depth 203 mm
Height 50 mm
Weight 1000 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Ruckus Wireless ZoneFlex 7982 below.

Is your question not listed? Ask your question here

No results