Pairing the Blood Pressure Monitor with your Smart-phone To begin using Bluetooth® for the rst time, please visit the website at http://www.rossmax.com for the initial set-up instructions. 1. Download and install the applicable APP onto your smartphone.2. To bind this device with your smartphone, turn on the device, Bluetooth® and the App of smartphone, and fol-low set-up and binding instructions.3. If the binding is successful, the Bluetooth® symbol ( ) will appear on the display and keep ashing during data transfer. The current measured value will automatically be transferred to the App when the measurement is completed.4. If the binding has failed, the Bluetooth® symbol ( ) will not appear on the display and the current measured value will not automatically be transferred to the App. In this case, the value is saved in the selected user memory zone. Please re-bind this device with your smartphone and follow App instructions for Bluetooth® transfer.
APP
APPAPP
APP
120mmHg120mmHg
USB
PC
BP Manager
APPAPPAPPAPP120mmHg120mmHg
USB
PC
BP Manager1. The monitor has two memory zones (1 and 2). Each zone can store up to 60 measure-ments.2. To read memory values from a selected memory zone, use the User-Switching key to select a memory zone (1 or 2) from which you want to recall values. Press the Memory key. The rst reading displayed is the average of all morning readings from the last 7 days.3. Continue to press the Memory key to view the average of all nighttime readings from the last 7 days.4. Press the Memory key again to view the average of the last 3 measurements stored in memory, and the last previously stored measurement. Every measurement comes with an assigned memory sequence number.5. All readings currently saved on the device can be transferred to the App using Blue-tooth® after successful completion of the binding process. Select the desired user memory zone and follow App instructions, the Bluetooth® transfer starts automatically. Data transfer will be halted while performing a measurement or operating the device.Note: The memory bank can store up to 60 readings per memory zone. When the num-ber of readings exceeds 60, the oldest data will be replaced with the new record. Note: AM is dened as 4:00 AM – 11:59 AMNote: PM is dened as 6:00 PM – 2:00 AM1. Press the User-Switching key to select memory zone 1 or memory zone 2.2. Press and hold the Memory key for approximately 5 seconds, then the data in the mem-ory zone can be erased automatically.1. Adjust the date/time/Bluetooth® in the monitor by installing or replacing batteries or holding down the ON/OFF/START key for approximately 5 seconds under power o mode. The display will show a blinking number showing the year.2. Change the year by pressing the Memory key, each press will increase the number. Press the ON/OFF/START key to conrm the entry and the screen will show a blinking number representing the date.3. Change the date, the hour and the minute as described in Step 2 above, using the Memory key to change and the ON/OFF/START key to conrm the entries.4. After adjusting the date/time, the Bluetooth® symbol ( ) and the blinking icon “ ” will be shown on the display simultaneously. Use the Memory key to choose whether automatic Bluetooth® data transfer is activated (Bluetooth® symbol ( )+ ) or de-activated (Bluetooth® symbol ( )+ ) and conrm with the ON/OFF/START key.5. Press the ON/OFF/START key again, “0” will reappear as the Blood Pressure Monitor is ready for measurement.Rossmax provides a free, integrated and user-friendly blood pressure management soft-ware which can be downloaded and installed on your computer. You may purchase a spe-cial designed USB cable in order to connect Rossmax’s blood pressure monitor and your PC. Please visit the website at http://www.rossmax.com for proceeding the downloading and installation process.If any abnormality will arise during use, please check the following points. Symptoms Check Points CorrectionNo display when the ON/OFF/START key is pressedHave the batteries run down? Replace them with four new batteries.Have the batteries' polarities been positioned incorrectly?Re-insert the batteries in the correct positions.EE mark shown on display or the blood pressure value is displayed excessively low (high)Is the cuff placed correctly?Wrap the cuff properly so that it is positioned correctly.Did you talk or move during measurement?Measure again. Keep arm steady dur-ing measurement.Did you vigorously shake the cuff during measurement?Note: If the unit still does not work, return it to your dealer. Under no circumstance should you disassemble and repair the unit by yourself.
1. The unit contains high-precision assemblies. Therefore, avoid extreme temperatures, hu-
midity, and direct sunlight. Avoid dropping or strongly shocking the main unit, and pro-tect it from dust.2. Clean the blood pressure monitor body and the cu carefully with a slightly damp, soft cloth. Do not press. Do not wash the cu or use chemical cleaner on it. Never use thinner, alcohol or petrol (gasoline) as cleaner.3. Leaky batteries can damage the unit. Remove the batteries when the unit is not used for a long time.4. The unit should not be operated by children so to avoid hazardous situations.5. If the unit is stored near freezing, allow it to acclimate at room temperature before use.6. This unit is not eld serviceable. You should not use any tool to open the device nor should you attempt to adjust anything inside the device. If you have any problems, please contact the store or the doctor from whom you purchased this unit or please contact Rossmax International Ltd.7. As a common issue for all blood pressure monitors using the oscillometric measurement function, the device may have diculty in determining the proper blood pressure for us-ers diagnosed with diabetes, poor circulation of blood, kidney problems, or for users suf-fered from stroke, or for unconscious users.8. This unit is able to detect common arrhythmia (atrial or ventricular premature beats or atrial brillation). The ARR, AFib and PC icons are displayed after the measurement if Atrial Fibrillation and Premature Contraction was detected during the measurement. If ARR, AFib or PC icons are displayed, you are advised to wait for a while and take another meas-urement. It is strongly recommended that you consult your physician if the ARR, AFib or PC icons appear often.9. While the given device is able to detect specic pulse arrhythmia, the measurement ac-curacy of the blood pressure meter may be impaired with the occurrence of pulse ar-rhythmia. 10. To stop operation at any time, press the ON/OFF/START key, and the air in the cu will be rapidly exhausted.
11. Once the ination reaches 300 mmHg, the unit will start deating rapidly for safety rea-
sons.12. Please note that this unit can be a home healthcare product, but it is not intended to serve as a substitute for the advice of a physician or medical professional.
13. Do not use this device for diagnosis or treatment of any health problem or disease. Meas-
urement results are for reference only. Consult a healthcare professional for interpreta-tion of pressure measurements. Contact your physician if you have or suspect any medi-cal problem. Do not change your medications without the advice of your physician or healthcare professional.14. Electromagnetic interference: Avoid strong electrical or electromagnetic elds in the direct vicinity of the device (e.g.mobile telephones, microwave ovens) or less than 1,5 km from AM, FM or TV broadcast antennas. These may lead to temporary impairment of measurement accuracy.15. Dispose of device, batteries, components and accessories according to local regulations.16. This monitor may not meet its performance specication if stored or used outside tem-perature and humidity ranges specied in Specications.Measurement Method OscillometricMeasurement Range Pressure: 30~260 mmHg; Pulse: 40~199 beats/ minutePressure SensorSemi conductor
Accuracy Pressure: ± 3mmHg; Pulse: ± 5% of reading
InflationPump DrivenDeflationAutomatic Air Release ValveMemory capacity60 memories for each zone x 2 zonesAuto-shut-off1 minute after last key operationPermissible Operating Temperature and Humidity10°C~40°C (50°F~104°F); 15%~85% RH; 700~1060
hPa
Permissible Transport and Storage Temperature and Humidity-10°C~60°C (14°F~140°F); 10%~90% RH; 700~1060
hPa
DC Power SourceDC 6V four AAA Batteries
AC Power Source DC 6V, ≥600mA (Plug size: outer(-) is Ø4.0, in-
Type BF: Device and cuff are designed to provide special protection against electrical shocks.IP ClassificationIP21: Protection against harmful ingress of water and particulate matter*Specifications are subject to change without notice.Recalling Values from MemoryClearing Values from MemoryTime and Bluetooth® AdjustmentData Transfer via Bluetooth®Data Transfer to PCTroubleshootingCautionary NotesSpecications
6. If Bluetooth® has been activated, the data is automatically transferred to the App after suc-
cessful completion of the binding process, please see Data Transfer via Bluetooth®.
This blood pressure monitor will re-inate automatically to higher pressure if the system detects that more pressure is needed to take a blood pressure measurement.Note: 1. This monitor automatically switches o approximately 1 minute after last key op-eration.2. To interrupt the measurement, simply press the ON/OFF/START key; the cu will deate immediately.17. Please note that when inating, the functions of the limb in question may be impaired.18. During the blood pressure measurement, blood circulation must not be stopped for an unnecessarily long time. If the device malfunctions, remove the cu from the arm.19. Avoid any mechanical restriction, compression or bending of the cu line.20. Do not allow sustained pressure in the cu or frequent measurements. The resulting re-striction of the blood ow may cause injury.21. Ensure that the cu is not placed on an arm in which the arteries or veins are undergoing medical treatment, e.g. intravascular access or therapy, or an arteriovenous (AV) shunt.
22. Do not apply the cu on the side, where a mastectomy has been performed in your
patient history.23. Do not place the cu over wounds as this may cause further injury.24. Only ever use the cus provided with the monitor or original replacement cus. Other-wise erroneous results will be recorded.25. Batteries can be fatal if swallowed. You should therefore store the batteries and products where they are inaccessible to small children. If a battery has been swallowed, call a doc-tor immediately.26. Do not use the tubing and/or AC adaptor for any other purpose than those specied, as they can cause risk of strangulation.27. Do not service or maintain device and cu while in use. 28. This device should not be used adjacent to or stacked with other equipment.29. Please do not use any other cables or accessories not approved by the manufacturer in this manual to avoid negative inuence on electromagnetic compatibility.
APP
APP
APP
APP120mmHg120mmHg
USB
PC
BP Manager
Electromagnetic Compatibility Information1. This device needs to be installed and put into service in accordance with the information provided in the user manual.2. WARNING: Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the X5, including cables specied by the manufacturer. Otherwise, degradation of the performance of this device could result.If higher IMMUNITY TEST LEVELS than those specied in Table 9 are used, the minimum separation distance may be lowered. Lower minimum separation distances shall be calculated using the equation specied in 8.10.Manufacturer’s declaration-electromagnetic immunityThe X5 is intended for use in the electromagnetic environment specied below. The customer or the user of the X5 should assure that is used in such and environment.Immunity
test
IEC 60601 test levelCompliance levelElectromagnetic environment-guidance
Conducted RF IEC 61000-4-63 Vrms: 0,15 MHz – 80 MHz6 Vrms: in ISM and amateur radio bands between 0,15 MHz and 80 MHz 80 % AM at 1 kHz 3 Vrms: 0,15 MHz – 80 MHz6 Vrms: in ISM and amateur radio bands between 0,15 MHz and 80 MHz 80 % AM at 1 kHz Portable and mobile RF communications equipment should be used no closer to any part of the X5 including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.Recommended separation distance:d = 1,2 √P, d = 1,2 √P 80MHz to 800 MHz, d = 2,3 √P 800MHz to 2,7 GHz Where P is the maximum output power rating of the transmitter in watts (W) ac-cording to the transmitter manufacturer and d is the recommended separation distance in metres (m).Interference may occur in the vicinity of equipment marked with the following symbol: Radiated RF IEC 61000-
4-3
10 V/m80 MHz – 2,7 GHz 80 % AM at 1 kHz10 V/m80 MHz – 2,7 GHz 80 % AM at 1 kHzNOTE1: At 80 MHz and 800 MHz, the higher frequency range applies.NOTE2: These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and reection from structures, objects and people.More information on EMC compliance of the device can be obtained from Rossmax website: www.rossmax.comNotes: 1. Unbinding your device will not delete the data from the App. 2. If you re-bind your smartphone with your blood pressure monitor, all prior reading history stored on the phone App will be retained. 3. Bluetooth® data transfer will reduce the battery capacity.IN0X50000000000XXOBM_IB_X5(2)NA17BT_EN_SW_ver2021
WARNING: The symbol on this product means that it's an electronic product and
following the European directive 2012/19/EU the electronic products have to be dis-posed on your local recycling centre for safe treatment.Rossmax Swiss GmbH, Widnauerstrasse 1, CH-9435 Heerbrugg, Switzerland
Model: X5
www.rossmax.com
Warranty CardThis instrument is covered by a 5 year guarantee from the date of purchase. The guar-antee is valid only on presentation of the warranty card completed or stamped by the seller/dealer confirming date of purchase or the receipt. Batteries, cuff and accessories are not included. Opening or altering the instrument invalidates the guarantee. The guarantee does not cover damage, accidents or non-compliance with the instruction manual. Please contact your local seller/dealer or www.rossmax.com.Customer Name: ____________________________________________________Address: ___________________________________________________________Telephone: __________________________________________________________E-mail address: ______________________________________________________Product InformationDate of purchase: ___________________________________________________Store where purchased: ____________________________________________________________________
Blood Pressure Monitor
- The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Rossmax International Ltd. is under
license. Other trademarks and trade names are those of their respective owners.
- The blood pressure monitor uses Bluetooth®(Bluetooth® low energy technology)
- Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
- Google Play and the Google Play logo are trademarks of Google Inc.Data Transfer via Bluetooth®Please download and install the free Healthstyle APP onto your smartphoneHealthstyle APP
View the manual for the Rossmax X5 BT here, for free. This manual comes under the category sphygmomanometer and has been rated by 1 people with an average of a 9. This manual is available in the following languages: English. Do you have a question about the Rossmax X5 BT or do you need help? Ask your question here
Need help?
Do you have a question about the Rossmax and is the answer not in the manual?
Receive updates on solutions
Get answers to your question
Question and answer
Number of questions: 0
The Rossmax X5 BT sphygmomanometer is a medical device used for measuring blood pressure. It is equipped with Bluetooth technology for easy data transfer to mobile devices. The device features a large LCD display for clear readings and operates silently for user convenience. The Rossmax X5 BT sphygmomanometer has a cuff size range suitable for adult users. It also offers irregular heartbeat detection to alert users of any potential issues. This device runs on batteries for portability and ease of use. The Rossmax X5 BT sphygmomanometer is designed to meet quality and accuracy standards for blood pressure monitoring. It is a reliable tool for healthcare professionals and individuals monitoring their blood pressure at home.
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Rossmax X5 BT below.
What does systolic pressure mean?
Systolic pressure is the top number that the blood pressure monitor will indicate. Systolic pressure refers to the amount of pressure in your arteries during the contraction of your heart muscle.
What does diastolilc pressure mean?
Diastolic pressure is the lowest number that the blood pressure monitor will indicate. The bottom number refers to your blood pressure when your heart muscle is between beats.
What is a normal blood pressure?
A normal blood pressure is about 120/80.
Is the manual of the Rossmax X5 BT available in English?
Yes, the manual of the Rossmax X5 BT is available in English .
Need help?
Do you have a question about the Rossmax and is the answer not in the manual?
Question and answer
Number of questions: 0