Rossmax SA310 manual

Rossmax SA310
8.2 · 1
PDF manual
 · 2 pages
English
manualRossmax SA310
SpO2
Measuring range 35% – 100% (the resolution is 1%)Accuracy 70% - 100%: ±2 %, 35% - 69%: unspeciedPulse Rate Measuring range 30 – 250 bpm (the resolution is 1 bpm)Accuracy 30 – 250 ± 3 digitsProbe TypeProbe model Rossmax PA100, PB100, PC100, PD100(Single Use), PF100 Extension cord Rossmax PE100Optical Sensor The wavelength of red LED is 660nm and Infrared LED is 905/880nm with maximum optical output power of 4mW.Electrical SpecicationBattery AA * 4 (Alkaline)Battery Life Continually for 15 hours with 4 alkaline batteriesAC Adaptor Model: HK-X205-A06, HK-XW05-A06, (W=1,2,3,4), HKKS-13116, HKKS-13117Input: AC100-240V, 50/60Hz, 0.2A max; Output: DC 6V, 0.8AEnvironmental conditionsOperation Condition Temperature: 5°C – 40°C (41°F – 104°F), Relative Humidity:15% – 95%(non condensing), Atmospheric pressure: 700hPa ~ 1060hPaStorage /Transport ConditionTemperature: -25°C – 70°C (-13°F – 158°F), Relative Humidity:15% – 90%(non condensing), Atmospheric pressure: 700hPa ~ 1060hPaNote: The condition of -25°C or 70°C back to use should stand for 3 hours at room temperature.Dimension Size: 14.5(L) x 7.25(W) x 2.25cm(H)Weight About 150g (without the batteries)Standard IEC/EN60601-1, IEC/EN60601-1-2, IEC/EN60601-1-11, ISO80601-2-61Symbol DescriptorsManufacturerSerial numberEU representativeType BF (Body FloatingIP Classication IP22: Protected against foreign objects and moistureCE MarkWarning: the symbol on this product means that it’s an electronic product and following the European directive 2012/19/EU the electronic products have to be dispose on your local recycling centre for safe treatment. Symptoms Check points CorrectionsSpO2 or Pulse rate cannot displayed
15:36
09 / 14 / 2018
98988686
% SpO
2
BPM
999
M
Low
High
15:36
09 / 14 / 2018
15:36
09 / 14 / 2018
15:36
09 / 14 / 2018
15:36
09 / 14 / 2018
98988686
BPM
999
M
% SpO
2
15:36
09 / 14 / 2018
98988686
BPM
999
M
% SpO
2
15:36
09 / 14 / 2018
98988686
BPM
999
M
% SpO
2
15:36
09 / 14 / 2018
BPM
- -
- -
% SpO
2
15:36
09 / 14 / 2018
0000
BPM
999
M
% SpO
2
15:36
09 / 14 / 2018
0000
BPM
% SpO
2
The icon “- -“ shows on the screenPlace the nger properly and try again.
ACT PPG
This icon means probe connect failure.Be sure ”Rossmax” probe is connected to the device correctly.
ACT PPG
This icon means probe dysfunctionReplace with new probe.Applied nger improperlyPlace the nger properly and try againSpO2 or Pulse rate are not displayed stablyFinger is shaking or body is moving Keep body steadyApplied nger improperlyPlace the nger properly and try againNo display when the bottom is pressedBatteries run down Replace with new batteriesBatteries inserted incorrectly Re-insert batteries Note: After clearing data, the icon will show 0 data.Caution: The deleted data could not be restored.WarningCleaningMaintenanceMemories mode- Save CycleMemories mode- Clear DataSpecification Troubleshooting Audio Signals
This device is not intended for use by people (including children) with restricted physical, sensory or
mental skills or a lack of experience and/or a lack of knowledge, unless they are supervised by a per- son who has responsibility for their safety or they receive instructions from this person on how to use the device. Children should be supervised around the device to ensure they do not play with it.• This device only for spot-checking, but not medical result evaluation.
This device is designed to determine the percentage of arterial oxygen saturation of functional
hemoglobin. Factors that may degrade pulse oximeter performance or affect the accuracy of the measurement include the following:
- Do not apply the pulse oximeter on the same arm as a blood pressure cuff, arterial catheter or
infusion line (s) - Excessive light, such as sunlight or direct home lighting. - Not steady at the site of application (e.g. trembling) - Moisture in the device - Improperly applied device - Finger is too large or too small to fit into the device - Poor pulse quality - Venous pulsations - Anemia or low hemoglobin concentrations - Cardio green and other intravascular dyes - Carboxyhemoglobin - Methemoglobin - Dysfunctional hemoglobin - Artificial nail or fingernail polish - On fingers with anatomical changes, oedemas, scars or burns.
- The conditional of probe. Use only the Rossmax approved pulse oximeter sensor, cable and
accessories. These parts are not reprocessed. Use of other sensors, cable and accessories can result in inaccurate readings.
Using the device for long periods may cause pain for people with circulatory disorders. Reposition
the device (probe) at least once every 4 hours to allow the patient’s skin to breath and to check patient’s condition regularly. • Do not use the device near flammable or explosive gas mixtures.• Do not use the device during an MRI or CT scan.• The device will be affected by electromagnetic interference during operation.• A warning that other cables and accessories may negatively affect EMC performance.
The device may not work when circulation is reduced. Warm or rub the finger, or re-position the
device.
This device is a precision electronic instrument and must be repaired by qualified technical
professionals. Field repair of the device is not possible. Do not attempt to open the case or repair the electronics. Opening the case may damage the device and void the warranty.• Do not overextend the device’s spring.• A functional tester cannot be used to access the accuracy of a pulse oximeter monitor.
Do not self-diagnose or self-medicate on the basis of the measurements without consulting your
doctor. In particular, do not start taking any new medication or change the type and/or dosage of any existing medication without prior approval.
Do not look directly inside the housing during the measurement. The red light and the invisible
infra-red light in the probe are harmful to your eyes. • Please be aware that user with susceptible skin.
As with all medical equipment, carefully route patient cabling to reduce the possibility of patient
entanglement or strangulation.• The maximum temperature might reach 42.4°C when operating for long time.
The oximeter is calibrated in the factory before sale, there is no need to calibrate it during its life
cycle.• Do not reuse or disinfect disposable SpO2 probe. (only for PD100)• The product is with a service life of 5 years is the course of regular use.
If any serious incident (e.g. death) has occurred in relation to the device should be reported to
the dealer, manufacturer, and the competent authority of Member State in which the user and/or patient is established.
1. Please clean the surface of the device before using. Wipe the device with medical alcohol
(70% (w/w) Ethanol) first, and then let it dry in air or clean it by dry clean fabric.
2. Using the medical alcohol to clean the product after use, prevent from cross infection for next
time use.
3. The best storage environment of the device is -25°C ~ 70°C ambient temperature and not higher
than 90% relative humidity.
Note: 1. Do not sterilize, autoclave or immerse this device in liquid. Do not pour or spray any liquids
onto the device.
2. Do not use caustic or abrasive cleaning agents, or any cleaning agent containing ammonium
chloride or isopropyl alcohol.
Recommends user to return this device to the manufacturer perform the following checks every 24
months.• Inspect the equipment for mechanical and functional damage or deterioration.• Ensure all user interface keys and accessories function normally.Note: Manufacturer use Index2 simulator to verify operation of the pulse oximeter device.Optional of memory interval: 60 / 30 / 10 seconds
Press the button and / button to highlight “Memory” option, and then press the
button to select the option.
Entry “Memory Mode”, press the / button to highlight “Save Cycle” option, and then press
the button to select the option.
Entry “Save Cycle”, press the / button to highlight option, and then press the button
to select the option.
Press the / button to change the value; press the button to save the desired value.
Press the / button and the button to select “Back/Exit” to return.
Press the button and / button to highlight “Clear Data” option, and then press the
button to select the option.
Entry “Clear Data”, press the / button to highlight “Sure” option, and then press the
button to select the option.
Press the / button and the button to select “Back/Exit” to return.
No. Name LCD Display Sound Control
1 Power on
V0.00
15:3609 / 14 / 2018
9898
8686
% SpO
2
BPM
999
M
Low
High
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
9898
8686
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
9898
8686
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
9898
8686
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
BPM
- -
- -
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
00
00
BPM
% SpO
2
Beep for 2 secondsPress buttonSoftware version
start measure
2
Pulse search The icon ickersX X
3
Max./ Min SpO2 and Pulse rate warningShow or in red icon.Reects upper or lower alarm limits.Beep-beep sounded repeatedlyDefaultMute for temporary, will Beep-beep sounded after two minutes. modeMute before power o modeBar Chart
Entry “Data History, press the / button to highlight “Bar Chart” option for viewing statistics
of SpO2, and then press the button to select the option.• Entry “SpO2 Memory Data”, press the button to go back to the monitoring screen. Memory Transfer to ROSSMAX Software
Entry into “Data History”, press the / button to highlight “Memory Transfer” option, and
then press the button to start data transmission for a few seconds.
Note: Before entering the data history mode, the icon should collect more than 1 data.
4
Probe failure alarm
15:3609 / 14 / 2018
98
98
86
86
% SpO
2
BPM
999
M
Low
High
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
BPM
- -
- -
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
% SpO
2
The icon shows on the screenBeep-beep sounded repeatedly
X
5
Probe connect failure alarm
15:3609 / 14 / 2018
98
98
86
86
% SpO
2
BPM
999
M
Low
High
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
BPM
- -
- -
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
% SpO
2
The icon shows on the screenBeep-beep sounded repeatedly
x
6
Low
battery alarm
15:3609 / 14 / 2018
98
98
86
86
% SpO
2
BPM
999
M
Low
High
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
BPM
- -
- -
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
% SpO
2
The icon shows on the screenBeep-beep sounded repeatedly for 1 minute and power o
x
7
Automatic
O
X
Beep-beep sounded and then power o After pulse is unde-tectable for around 1 minute.
8
Unable measure
15:3609 / 14 / 2018
98
98
86
86
% SpO
2
BPM
999
M
Low
High
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
98
98
86
86
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
BPM
- - - -
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
999
M
% SpO
2
15:3609 / 14 / 2018
0
0
0
0
BPM
% SpO
2
Blood saturation & pulse rate appears “ - - “Beep-beep sounded repeatedly.
x
9 AC Power icon
X
Remove or connect AC power cable to device.Note: Description of the effect on displayed and transmitted SpO2 and pulse rate:• Data averaging: 4 seconds for SpO2; 8 seconds for pulse rate.• Data update delay: Less than 2 seconds.• Alarm condition delay: Less than 8 seconds for SpO2; Less than 16 seconds for pulse rate.• Alarm signal generation delay: Less than 1 second for SpO2 and pulse rate.The display disappears suddenlyThe device will auto power o when it gets no signalNormalLow battery Replace with new batteries
Note: If the unit does not work, return it to your dealer. Under no circumstance should you
disassemble and repair the unit by yourself.
Model: SA310

www.rossmax.com

Handheld Pulse Oximeter

SettingsDateTimeAlarm SpOAlarm PRMemory
Memory
Exit
2
Memory ModeBackClear DataSave Cycle
Save Cycle
Data HistoryMemory OffSave Cycle

60

SecBackSave Cycle

30

SecBackSave Cycle

10

SecBackSave Cycle

10

SecBack
Back
Settings
Date
Time
Alarm SpOAlarm PRMemory
Exit
2
SettingsDateTimeAlarm SpOAlarm PRMemory
Memory
Exit
2
Clear DataBackSure
Sure
Clear DataBack
Back
SureMemory ModeBackClear Data
Clear Data
Save CycleData HistoryMemory Off
Settings
Date
Time
Alarm SpOAlarm PRMemory
Exit
2
Settings
Date
Time
Alarm SpOAlarm PRMemory
Memory
Exit
2
Memory ModeBackClear Data
Save CycleSave Cycle
Data HistoryMemory OffSave Cycle

60

SecBackSave Cycle

30

SecBackSave Cycle

10

SecBackSave Cycle

10

Sec
BackBack
SettingsDateTimeAlarm SpOAlarm PRMemoryExit
2
Settings
Date
Time
Alarm SpOAlarm PRMemory
Memory
Exit
2
Clear DataBack
SureSure
Clear Data
BackBack
SureMemory ModeBack
Clear DataClear Data
Save CycleData HistoryMemory OffSettingsDateTimeAlarm SpOAlarm PRMemoryExit
2
SettingsDateTimeAlarm SpOAlarm PR
MemoryMemory
Exit
2
Memory Mode
Back
Clear DataSave Cycle
Save Cycle
Data HistoryMemory Off
Save Cycle

60

SecBackSave Cycle

30

SecBackSave Cycle

10

SecBackSave Cycle

10

Sec
BackBack
SettingsDateTimeAlarm SpOAlarm PRMemoryExit
2
SettingsDateTimeAlarm SpOAlarm PR
MemoryMemory
Exit
2
Clear DataBack
SureSure
Clear Data
BackBack
Sure
Memory Mode
Back
Clear Data
Clear Data
Save CycleData HistoryMemory Off
SettingsDateTimeAlarm SpOAlarm PRMemoryExit
2
SettingsDateTimeAlarm SpOAlarm PR
MemoryMemory
Exit
2
Memory ModeBackClear Data
Save CycleSave Cycle
Data HistoryMemory OffSave Cycle

60

SecBackSave Cycle

30

SecBack
Save Cycle
10
Sec
Back
Save Cycle

10

Sec
BackBack
SettingsDateTimeAlarm SpOAlarm PRMemoryExit
2
SettingsDateTimeAlarm SpOAlarm PR
MemoryMemory
Exit
2
Clear Data
Back
Sure
Sure
Clear Data
BackBack
SureMemory ModeBack
Clear DataClear Data
Save CycleData HistoryMemory OffSettingsDateTimeAlarm SpOAlarm PRMemoryExit
2
60/30/10 secondsElectromagnetic Compatibility Information1. This device needs to be installed and put into service in accordance with the information provided in the user manual.2. WARNING: Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the SA310, including cables specied by the manufacturer. Otherwise, degradation of the performance of this device could result.If higher IMMUNITY TEST LEVELS than those specied in Table are used, the minimum separation distance may be lowered. Lower minimum separation distances shall be calculated using the equation.IN0SA311000000031RI_IB_SA310_2Yr_EN_TP_ver2043Warranty CardThis instrument is covered by a 2 year guarantee from the date of purchase, batteries and accessories are not included. The guarantee is valid only on presentation of the guarantee card completed by the dealer confirming date of purchase or the receipt. Opening or altering the instrument invalidates the guarantee. The guarantee does not cover damage, accidents or non-compliance with the instruction manual. Please contact your local seller/dealer or www.rossmax.com.Customer Name: __________________________________________________________Address: _________________________________________________________________Telephone: _______________________________________________________________E-mail address: ____________________________________________________________Product Information: Date of purchase: __________________________________________________________Store where purchased: __________________________________________________________________________Rossmax InnoTek Corp.
12F., No. 189, Kang Chien Rd., Taipei, 114, Taiwan.
CMC Medical Devices & Drugs S.L.C/ Horacio Lengo N° 18, CP 29006, Málaga, SpainManufacturer’s declaration-electromagnetic immunityThe SA310 is intended for use in the electromagnetic environment specied below. The customer or the user of the SA310 should assure that is used in such and environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic environment-guidance
Conducted RF IEC 61000-4-63 Vrms: 0,15 MHz – 80 MHz6 Vrms: in ISM and amateur radio bands between 0,15 MHz and 80 MHz 80 % AM at 1 kHz 3 Vrms: 0,15 MHz – 80 MHz6 Vrms: in ISM and amateur radio bands between 0,15 MHz and 80 MHz 80 % AM at 1 kHz Portable and mobile RF communications equipment should be used no closer to any part of the SA310 including cables, than the recommended separation distance calcu-lated from the equation applicable to the fre-quency of the transmitter.Recommended separation distance:d = 1,2 √P, d = 1,2 √P 80MHz to 800 MHz, d = 2,3 √P 800MHz to 2,7 GHz Where P is the maximum output power rat-ing of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres
(m).
Interference may occur in the vicinity of equipment marked with the following sym-bol: Radiated RF IEC 61000-4-310 V/m80 MHz – 2,7 GHz 80 % AM at 1 kHz10 V/m80 MHz – 2,7 GHz 80 % AM at 1 kHzNOTE1: At 80 MHz and 800 MHz, the higher frequency range applies.NOTE2: These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorp-tion and reection from structures, objects and people.More information on EMC compliance of the device may be obtained from Rossmax using the contacts shown in this manual.The text is subject to change without further notice.

View the manual for the Rossmax SA310 here, for free. This manual comes under the category heart rate monitor and has been rated by 1 people with an average of a 8.2. This manual is available in the following languages: English. Do you have a question about the Rossmax SA310 or do you need help? Ask your question here

Need help?

Do you have a question about the Rossmax and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Rossmax SA310 is a heart rate monitor device which provides real-time monitoring of the user's heart rate. It features an easy-to-read LCD display that shows clear and accurate readings. The monitor is equipped with a chest strap that securely and comfortably fits around the user's chest, allowing for continuous heart rate tracking during various activities. The Rossmax SA310 is powered by a long-lasting battery, ensuring reliable performance over time. The device is designed for convenience, with a lightweight and compact build that makes it easy to wear and carry. The Rossmax SA310 is suitable for use during exercise, sports, or any other activities where heart rate monitoring is desired. The device is designed with precision and quality in mind, offering users a reliable and accurate way to monitor their heart rate.

General
BrandRossmax
ModelSA310
Productheart rate monitor
LanguageEnglish
FiletypeUser manual (PDF), Brochure (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Rossmax SA310 below.

How much should I exercise as an adult per week?

As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.

How high is an adult's heart rate at rest?

An adult's resting heart rate is between 60 and 100 beats per minute.

What is an adult's maximum heart rate?

As a rule of thumb for your maximum heart rate, you can use 220 minus your age.

Is the manual of the Rossmax SA310 available in English?

Yes, the manual of the Rossmax SA310 is available in English .

Is your question not listed? Ask your question here

No results